Makerfabs · ESP32-S3 · 1.9" · 170×320
MaTouch ESP32-S3 Parallel TFT with Touch 1.9" specifications
This page collects the pinout and hardware details of the MaTouch ESP32-S3 Parallel TFT 1.9". The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Most 1.9-inch ESP32 boards drive their ST7789 over SPI. Makerfabs went with an 8-bit 8080 parallel bus instead: data on GPIO 9 to 16, WR 38, RD 39, DC 47, CS 46 and reset 48. That costs pins but lets full-screen redraws go noticeably faster than SPI at the same clock.
Touch is a CST816D on its own I2C pair (SDA 7, SCL 8) with the interrupt on GPIO 40, and the backlight sits on GPIO 45. A microSD slot uses SPI on GPIO 1, 2, 41 and 42, and the battery voltage can be read on GPIO 3. There's a LiPo connector with an onboard charger and native USB on the USB-C port.
Makerfabs doesn't publish the flash or PSRAM size for this board, but its README tells you to select OPI PSRAM in the Arduino settings, and the examples allocate buffers in PSRAM. Two small connectors marked UART and ADC are the expansion route; their GPIO numbers are only shown in pictures.

- Screen
- 1.9" · 170×320
- Chip
- ESP32-S3
- Memory
- 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.9-inch, 170×320, ST7789V2
- 8-bit 8080 parallel bus
- CST816D capacitive touch
- ESP32-S3 with octal PSRAM
- microSD slot
- LiPo charging, native USB-C
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 1.9" |
| Resolution | 170×320 px |
| Colour depth | 16-bit |
| Display controller | ST7789V2 (8-bit 8080 parallel) |
| Display interface | 8-bit 8080 parallel |
| Touch | CST816D (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Two expansion connectors (UART / ADC) whose GPIOs Makerfabs does not list in text. 3.7 V LiPo connector, native USB on USB-C. The README asks for OPI PSRAM in the Arduino settings but does not state flash and PSRAM sizes. |
| Display | 170×320, ST7789V2: D0-D7 GPIO 9 to 16, WR 38, RD 39, DC 47, CS 46, RST 48, backlight 45 |
| Touch | CST816D, SDA 7, SCL 8, INT 40 |
| microSD | CS 1, MOSI 2, MISO 41, SCK 42 |
| Battery | 3.7 V LiPo with charger, voltage on GPIO 3 |
| Ports | Two expansion connectors (UART / ADC) |
Board layout and connectors
Where each connector, button and LED sits on the MaTouch ESP32-S3 Parallel TFT with Touch 1.9-inch, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | microSD CS |
| GPIO 2 | microSD MOSI |
| GPIO 3 | Battery voltage (ADC) |
| GPIO 7 | I2C SDA (touch) |
| GPIO 8 | I2C SCL (touch) |
| GPIO 9 | LCD D0 |
| GPIO 10 | LCD D1 |
| GPIO 11 | LCD D2 |
| GPIO 12 | LCD D3 |
| GPIO 13 | LCD D4 |
| GPIO 14 | LCD D5 |
| GPIO 15 | LCD D6 |
| GPIO 16 | LCD D7 |
| GPIO 38 | LCD WR |
| GPIO 39 | LCD RD |
| GPIO 40 | Touch interrupt |
| GPIO 41 | microSD MISO |
| GPIO 42 | microSD SCK |
| GPIO 45 | Backlight |
| GPIO 46 | LCD CS |
| GPIO 47 | LCD DC |
| GPIO 48 | LCD reset |
Source: github.com, www.makerfabs.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- It isn't in the LCD Ultra Pro editor yet.
- Select OPI PSRAM in the Arduino board settings, as Makerfabs asks.
- Flash and PSRAM sizes are not published. Check your module.
What it is good for
- •Fast small dashboards
- •Battery-powered handhelds
- •Data loggers with a screen
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Is the MaTouch 1.9" display SPI or parallel?
Parallel: an 8-bit 8080 bus on GPIO 9 to 16 with WR 38, RD 39 and DC 47.
Which touch controller does it use?
A CST816D on I2C (GPIO 7/8), interrupt on GPIO 40.
Can it run from a battery?
Yes. There is a 3.7 V LiPo input with an onboard charger, and GPIO 3 reads the battery voltage.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the MaTouch parallel TFT family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.