Makerfabs · ESP32-S3 · 2.8" · 240×320
MaTouch ESP32-S3 Parallel TFT with Touch 2.8" specifications
This page collects the pinout and hardware details of the MaTouch ESP32-S3 Parallel TFT 2.8". The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Sixteen data lines for a 240×320 screen is more bandwidth than the panel strictly needs, and that's the point of this board. The ST7789 on the MaTouch Parallel 2.8 is wired as a 16-bit 8080 bus, so LVGL can push whole frames quickly without the SPI bottleneck.
Makerfabs' LovyanGFX config gives the full map. D0 to D15 sit on GPIO 47, 21, 14, 13, 12, 11, 10, 9, 3, 8, 16, 15, 7, 6, 5 and 4. WR is GPIO 18, RD 48, RS (DC) 17 and CS 46, while the LCD reset is tied to the board's reset line. Backlight is GPIO 45.
Touch is capacitive on I2C at GPIO 39/38, with interrupt 40 and reset 1. The microSD slot runs in 1-bit SDMMC mode on GPIO 2, 41 and 42. What the repo doesn't tell you is the touch chip model or the memory size. The examples use PSRAM, so there is some.

- Screen
- 2.8" · 240×320
- Chip
- ESP32-S3
- Memory
- Input
- capacitive touch
Key features
- 2.8-inch, 240×320, ST7789
- 16-bit 8080 parallel bus
- Capacitive touch
- microSD over SDMMC
- ESP32-S3 with PSRAM
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 2.8" |
| Resolution | 240×320 px |
| Colour depth | 16-bit |
| Display controller | ST7789 (16-bit 8080 parallel) |
| Display interface | 16-bit 8080 parallel |
| Touch | Capacitive (I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | Yes |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Pins from Makerfabs' LovyanGFX example config (Bus_Parallel16). The LCD reset is tied to the board reset. Makerfabs does not publish flash, PSRAM or the touch chip model in the README. |
| Display | ST7789, 16-bit: WR 18, RD 48, RS 17, CS 46, backlight 45 |
| Data bus | D0 47, D1 21, D2 14, D3 13, D4 12, D5 11, D6 10, D7 9, D8 3, D9 8, D10 16, D11 15, D12 7, D13 6, D14 5, D15 4 |
| Touch | I2C SDA 39, SCL 38, INT 40, RST 1 |
| microSD | CMD 2, CLK 42, D0 41 |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | Touch reset |
| GPIO 2 | microSD CMD |
| GPIO 3 | LCD D8 |
| GPIO 4 | LCD D15 |
| GPIO 5 | LCD D14 |
| GPIO 6 | LCD D13 |
| GPIO 7 | LCD D12 |
| GPIO 8 | LCD D9 |
| GPIO 9 | LCD D7 |
| GPIO 10 | LCD D6 |
| GPIO 11 | LCD D5 |
| GPIO 12 | LCD D4 |
| GPIO 13 | LCD D3 |
| GPIO 14 | LCD D2 |
| GPIO 15 | LCD D11 |
| GPIO 16 | LCD D10 |
| GPIO 17 | LCD RS (DC) |
| GPIO 18 | LCD WR |
| GPIO 21 | LCD D1 |
| GPIO 38 | I2C SCL (touch) |
| GPIO 39 | I2C SDA (touch) |
| GPIO 40 | Touch interrupt |
| GPIO 41 | microSD D0 |
| GPIO 42 | microSD CLK |
| GPIO 45 | Backlight |
| GPIO 46 | LCD CS |
| GPIO 47 | LCD D0 |
| GPIO 48 | LCD RD |
Source: github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- The LCD Ultra Pro editor does not support this board yet.
- Touch chip and memory sizes are not documented by Makerfabs.
- The parallel bus takes most GPIOs. Few are left for your own wiring.
What it is good for
- •Snappy small touch UIs
- •Weather and status displays
- •LVGL demos and learning
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
How wide is the display bus on the MaTouch Parallel 2.8"?
16 bits, in 8080 mode, with WR on GPIO 18 and RD on GPIO 48.
Is there an LCD reset GPIO?
No. The LCD reset is connected to the board reset.
Which pins does the SD card use?
SDMMC 1-bit: CMD GPIO 2, CLK GPIO 42, D0 GPIO 41.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the MaTouch parallel TFT family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.