Waveshare · ESP32-P4 · 4.3" · 480×800
Waveshare ESP32-P4-WIFI6-Touch-LCD-4.3 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-P4-WIFI6-Touch-LCD-4.3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
480×800 on 4.3 inches, in portrait by default, over a 2-lane MIPI-DSI link to an ST7701. Waveshare's 4.3-inch P4 board shows what the P4 does differently from an ESP32-S3: the display needs only a reset pin (GPIO 27) and a backlight pin (GPIO 26), and the 16 data lines of an RGB panel are gone.
Those freed pins end up on a 40-pin header that Waveshare says works with selected Raspberry Pi HATs through an adapter. There's also a 2-lane MIPI-CSI camera connector for an optional OV5647, a 4-bit microSD slot and a USB 2.0 High-Speed OTG port next to the USB-UART one.
Touch is a GT911 with up to five points. Audio pairs an ES8311 codec with an ES7210 front end, two microphones and a speaker connector. Memory is 32 MB of in-package PSRAM and 32 MB of flash, and an ESP32-C6-MINI-1 provides Wi-Fi 6 and Bluetooth 5. On all Waveshare P4 boards the shared pins are the same: I2C on GPIO 7 (SDA) and 8 (SCL), I2S audio on GPIO 9 to 13, the 4-bit microSD on GPIO 39 to 44 and the speaker amplifier enable on GPIO 53.

- Screen
- 4.3" · 480×800
- Chip
- ESP32-P4
- Memory
- 32 MB flash, 32 MB PSRAM (OPI/HPI)
- Input
- capacitive touch
Key features
- 4.3-inch IPS, 480×800, ST7701
- 2-lane MIPI-DSI
- GT911 touch, 5 points
- ESP32-P4: 32 MB PSRAM, 32 MB flash
- ES8311 + ES7210 audio
- 40-pin header, camera connector
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 4.3" |
| Resolution | 480×800 px |
| Colour depth | 16-bit |
| Display controller | ST7701 (MIPI-DSI, 2 lanes) |
| Display interface | MIPI-DSI |
| Touch | GT911 (capacitive, I2C, 5 points) |
| Microcontroller | ESP32-P4 |
| Module | ESP32-P4NRW32 + ESP32-C6-MINI-1 (Wi-Fi 6 / Bluetooth 5 over SDIO) |
| CPU clock | 400 MHz |
| Internal SRAM | 768 KB |
| PSRAM | 32 MB (OPI/HPI) |
| Flash | 32 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | ES8311 codec, ES7210 front end with two microphones, speaker connector, 2-lane MIPI-CSI camera connector (OV5647 optional), 4-bit microSD, USB 2.0 HS OTG, 40-pin header compatible with selected Raspberry Pi HATs via an adapter. |
| Display | 480×800, ST7701, MIPI-DSI 2 lanes, RST 27, backlight 26 |
| Touch | GT911 on I2C SDA 7 / SCL 8 |
| Camera | 2-lane MIPI-CSI, OV5647 optional |
| Storage | microSD, 4-bit SDIO 3.0 |
| Expansion | 40-pin header (selected Raspberry Pi HATs via adapter) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | Header GPIO |
| GPIO 5 | Header GPIO |
| GPIO 7 | I2C SDA (touch, codecs) |
| GPIO 8 | I2C SCL (touch, codecs) |
| GPIO 9 | I2S data out (ES8311) |
| GPIO 10 | I2S LRCLK |
| GPIO 11 | I2S data in (ES7210) |
| GPIO 12 | I2S SCLK |
| GPIO 13 | I2S MCLK |
| GPIO 21 | Header GPIO |
| GPIO 22 | Header GPIO |
| GPIO 24 | Header GPIO |
| GPIO 25 | Header GPIO |
| GPIO 26 | Backlight |
| GPIO 27 | LCD reset |
| GPIO 28 | Header GPIO |
| GPIO 29 | Header GPIO |
| GPIO 30 | Header GPIO |
| GPIO 31 | Header GPIO |
| GPIO 32 | Header GPIO |
| GPIO 34 | Header GPIO |
| GPIO 35 | Header GPIO (strapping pin) |
| GPIO 37 | UART0 TX (header) |
| GPIO 38 | UART0 RX (header) |
| GPIO 39 | microSD D0 |
| GPIO 40 | microSD D1 |
| GPIO 41 | microSD D2 |
| GPIO 42 | microSD D3 |
| GPIO 43 | microSD CLK |
| GPIO 44 | microSD CMD |
| GPIO 46 | Header GPIO |
| GPIO 47 | Header GPIO |
| GPIO 48 | Header GPIO |
| GPIO 49 | Header GPIO |
| GPIO 50 | Header GPIO |
| GPIO 51 | Header GPIO |
| GPIO 52 | Header GPIO |
| GPIO 53 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 2 | GPIO, PWM | On the 40-pin header |
| GPIO 3 | GPIO, PWM | On the 40-pin header |
| GPIO 4 | GPIO, PWM | On the 40-pin header |
| GPIO 5 | GPIO, PWM | On the 40-pin header |
| GPIO 21 | GPIO, PWM, ADC | On the 40-pin header |
| GPIO 22 | GPIO, PWM, ADC | On the 40-pin header |
| GPIO 24 | GPIO, PWM | On the 40-pin header |
| GPIO 25 | GPIO, PWM | On the 40-pin header |
| GPIO 28 | GPIO, PWM | On the 40-pin header |
| GPIO 29 | GPIO, PWM | On the 40-pin header |
| GPIO 30 | GPIO, PWM | On the 40-pin header |
| GPIO 31 | GPIO, PWM | On the 40-pin header |
| GPIO 32 | GPIO, PWM | On the 40-pin header |
| GPIO 34 | GPIO, PWM | On the 40-pin header |
| GPIO 35 | GPIO, PWM | On the 40-pin header; strapping pin, keep it free at boot |
| GPIO 46 | GPIO, PWM | On the 40-pin header |
| GPIO 47 | GPIO, PWM | On the 40-pin header |
| GPIO 48 | GPIO, PWM | On the 40-pin header |
| GPIO 49 | GPIO, PWM, ADC | On the 40-pin header |
| GPIO 50 | GPIO, PWM, ADC | On the 40-pin header |
| GPIO 51 | GPIO, PWM, ADC | On the 40-pin header |
| GPIO 52 | GPIO, PWM, ADC | On the 40-pin header |
| GPIO 37 | GPIO, UART_TX | UART0 TX on the 40-pin header |
| GPIO 38 | GPIO, UART_RX | UART0 RX on the 40-pin header |
- 40-pin header — GPIO 2, 3, 4, 5, 21, 22, 24, 25, 28, 29, 30, 31, 32, 34, 35, 46, 47, 48, 49, 50, 51, 52, 37, 38, 7, 8 · 2 x 20 pin header, Raspberry Pi style
SDA / SCL are GPIO 7 / 8 (the on-board I2C bus); also USB DP / DM, 3.3 V, 5 V and GND. Selected Raspberry Pi HATs fit through an adapter
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- Default orientation is portrait (480 wide, 800 tall).
- Wi-Fi goes through the ESP32-C6 co-processor.
What it is good for
- •Smooth LVGL interfaces
- •Camera viewers
- •Home Assistant panels with Wi-Fi 6
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32P4 Dev Module |
|---|---|
| Chip Variant | v3.00 or newer for rev3.x chips (the default); Before v3.00 only for confirmed rev1.x chips |
| PSRAM | Enabled |
| Flash Size | 32 MB |
| Flash Mode | QIO 80 MHz |
| Partition Scheme | 13 MB application / 7 MB data |
Board package: esp32 by Espressif Systems 3.3.11
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display driver does the 4.3-inch P4 board use?
An ST7701 on a 2-lane MIPI-DSI link, 480×800.
Can I use Raspberry Pi HATs?
Waveshare says selected HATs work on the 40-pin header through an adapter.
Which pins drive the display?
Only reset (GPIO 27) and backlight (GPIO 26); the image goes over the dedicated MIPI-DSI lanes.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-P4 family
Tools for this board
- ESP32-P4-WIFI6-Touch-LCD-4.3 Arduino IDE settings
- ESP32-P4-WIFI6-Touch-LCD-4.3 pin planner
- ESP32-P4-WIFI6-Touch-LCD-4.3 side-by-side comparison
- ESP32-P4-WIFI6-Touch-LCD-4.3 LVGL memory estimate
- ESP32-P4-WIFI6-Touch-LCD-4.3 I2C address check
- Other ESP32 boards with the ST7701
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.