Waveshare · ESP32-P4 · 7.0" · 1024×600
Waveshare ESP32-P4-WIFI6-Touch-LCD-7B specifications
This page collects the pinout and hardware details of the ESP32-P4-WIFI6-Touch-LCD-7B. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Industrial buses on a 7-inch touch panel. The 7B version of Waveshare's P4 display adds CAN (TWAI) and RS485 to the usual set, which makes it a candidate for machine HMIs and building automation, where a 1024×600 screen is a common size.
The display runs over two MIPI-DSI lanes at 1024×600. Note the pins: on this board the backlight is GPIO 32 and the LCD reset GPIO 33, not 26 and 27 like on the 4.3 and 5-inch boards. Touch is a GT911 with five points on the shared I2C bus.
Inside are 32 MB of PSRAM and 32 MB of flash, an ESP32-C6-MINI-1 for Wi-Fi 6 and Bluetooth 5, an ES8311 codec, an ES7210 with two microphones and a speaker header. Waveshare's managed component is waveshare/esp32_p4_wifi6_touch_lcd_7b. On all Waveshare P4 boards the shared pins are the same: I2C on GPIO 7 (SDA) and 8 (SCL), I2S audio on GPIO 9 to 13, the 4-bit microSD on GPIO 39 to 44 and the speaker amplifier enable on GPIO 53.

- Screen
- 7.0" · 1024×600
- Chip
- ESP32-P4
- Memory
- 32 MB flash, 32 MB PSRAM (OPI/HPI)
- Input
- capacitive touch
Key features
- 7-inch IPS, 1024×600, MIPI-DSI
- GT911 touch, 5 points
- CAN (TWAI) and RS485
- ESP32-P4: 32 MB PSRAM, 32 MB flash
- ES8311 + ES7210 audio
- Wi-Fi 6 via ESP32-C6
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 7.0" |
| Resolution | 1024×600 px |
| Colour depth | 16-bit |
| Display controller | MIPI-DSI panel (2 lanes) |
| Display interface | MIPI-DSI |
| Touch | GT911 (capacitive, I2C, 5 points) |
| Microcontroller | ESP32-P4 |
| Module | ESP32-P4NRW32 + ESP32-C6-MINI-1 (Wi-Fi 6 / Bluetooth 5 over SDIO) |
| CPU clock | 400 MHz |
| Internal SRAM | 768 KB |
| PSRAM | 32 MB (OPI/HPI) |
| Flash | 32 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | ES8311 codec, ES7210 ADC with two microphones, speaker header, microSD, USB 2.0 HS OTG, CAN (TWAI), RS485, I2C, UART and GPIO. |
| Display | 1024×600 IPS, MIPI-DSI 2 lanes, backlight 32, RST 33 |
| Touch | GT911, I2C SDA 7 / SCL 8 |
| Buses | CAN (TWAI), RS485, I2C, UART, GPIO |
| Audio | ES8311, ES7210, two mics, speaker header |
| Storage | microSD, 4-bit |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 7 | I2C SDA (touch, codecs) |
| GPIO 8 | I2C SCL (touch, codecs) |
| GPIO 9 | I2S data out (ES8311) |
| GPIO 10 | I2S LRCLK |
| GPIO 11 | I2S data in (ES7210) |
| GPIO 12 | I2S SCLK |
| GPIO 13 | I2S MCLK |
| GPIO 32 | Backlight |
| GPIO 33 | LCD reset |
| GPIO 39 | microSD D0 |
| GPIO 40 | microSD D1 |
| GPIO 41 | microSD D2 |
| GPIO 42 | microSD D3 |
| GPIO 43 | microSD CLK |
| GPIO 44 | microSD CMD |
| GPIO 53 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- The LCD Ultra Pro editor doesn't support it yet (it does support Waveshare's ESP32-S3 7B).
- Backlight and reset pins differ from the other P4 boards.
- CAN and RS485 need their own transceiver drivers in your firmware.
What it is good for
- •Machine and process HMIs
- •Building automation panels
- •Modbus / CAN dashboards
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32P4 Dev Module |
|---|---|
| Chip Variant | v3.00 or newer for rev3.x chips (the default); Before v3.00 only for confirmed rev1.x chips |
| PSRAM | Enabled |
| Flash Size | 32 MB |
| Flash Mode | QIO |
| Flash Frequency | 80 MHz |
| Partition Scheme | 13M APP / 7M data (32 MB) |
Board package: esp32 by Espressif Systems 3.3.11 (or newer 3.x)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Is this the same as the Waveshare ESP32-S3-Touch-LCD-7B?
No. Same panel size and resolution, but this one has an ESP32-P4 with MIPI-DSI and an ESP32-C6 for Wi-Fi 6.
Does it have CAN?
Yes, CAN (TWAI) and RS485 are on board.
Which pins drive the backlight and reset?
Backlight GPIO 32, LCD reset GPIO 33.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare ESP32-P4 family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.