LilyGO · ESP32-C5 · 1.9" · 170×320

LilyGO T-Display-C5 specifications

This page collects the pinout, free GPIOs and hardware details of the LilyGO T-Display-C5. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.

5 GHz Wi-Fi on an ESP32 with a screen. The T-Display-C5 is built around the ESP32-C5, Espressif's first chip with dual-band Wi-Fi 6, and it keeps the familiar T-Display shape: a 1.9-inch 170×320 ST7789 on SPI.

LilyGO's pin table is complete and short. The LCD uses SCK 7, MOSI 9, DC 8, CS 26, reset 23 and a PWM backlight on GPIO 25. I2C sits on GPIO 2 (SDA) and 3 (SCL), shared by the optional CST816S touch (interrupt 27, reset 24) and an AXP2602 battery gauge with its interrupt on GPIO 10. GPIO 0 is a user button and GPIO 28 the BOOT button.

Memory is 16 MB of flash and 8 MB of quad PSRAM. You'll need ESP-IDF 5.3 or later, or an Arduino core built on it, since older versions don't know the C5. For deep sleep, only GPIO 0 to 6 can wake the chip.

LilyGO T-Display-C5 board diagram with an example screen: 1.9" 170×320, ESP32-C5
Annotated diagram of the LilyGO T-Display-C5, drawn by LCD Ultra Pro™.
Screen
1.9" · 170×320
Chip
ESP32-C5
Memory
16 MB flash, 8 MB PSRAM (QSPI)
Input
capacitive touch

Key features

  • 1.9-inch, 170×320, ST7789 (SPI)
  • ESP32-C5: dual-band (2.4 / 5 GHz) Wi-Fi 6
  • 16 MB flash, 8 MB PSRAM
  • Optional CST816S touch
  • AXP2602 battery gauge
  • USB-C (USB-Serial-JTAG)

Specifications

LilyGO T-Display-C5 technical specifications
ManufacturerLilyGO
Screen size1.9"
Resolution170×320 px
Colour depth16-bit
Display controllerST7789 (SPI)
Display interfaceSPI
TouchCST816S (capacitive, I2C, optional)
MicrocontrollerESP32-C5
ModuleESP32-C5-WROOM-1
CPU clock240 MHz
Internal SRAM384 KB
PSRAM8 MB (QSPI)
Flash16 MB
Wi-FiYes
BluetoothYes
Hardware variantESP32-C5 with dual-band (2.4 / 5 GHz) Wi-Fi 6. AXP2602 battery gauge, optional CST816S touch, USB-C (USB-Serial-JTAG). Needs ESP-IDF 5.3 or later.
Display170×320, ST7789: SCK 7, MOSI 9, DC 8, CS 26, RST 23, backlight 25
TouchCST816S (optional), INT 27, RST 24
I2CSDA 2, SCL 3
ButtonsUser GPIO 0, BOOT GPIO 28
SoftwareESP-IDF 5.3 or later

GPIO pinout

The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.

LilyGO T-Display-C5 GPIO pinout
GPIOFunction
GPIO 0User button
GPIO 2I2C SDA (touch, AXP2602)
GPIO 3I2C SCL (touch, AXP2602)
GPIO 4Header GPIO
GPIO 5Header GPIO
GPIO 6Header GPIO
GPIO 7LCD SCK
GPIO 8LCD DC
GPIO 9LCD MOSI
GPIO 10AXP2602 interrupt
GPIO 23LCD reset
GPIO 24Touch reset
GPIO 25Backlight (PWM)
GPIO 26LCD CS
GPIO 27Touch interrupt
GPIO 28BOOT button

Source: github.com, github.com, github.com. Always check against your board revision before wiring.

Free GPIOs and connectors

These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.

Free GPIO pins of the LilyGO T-Display-C5
PinCapabilitiesNote
GPIO 4GPIO, PWM, ADCOn the expansion header
GPIO 5GPIO, PWM, ADCOn the expansion header
GPIO 6GPIO, PWM, ADCOn the expansion header
  • Expansion header — GPIO 4, 5, 6, 10, 23 · pin header

    Also UART TX0 / RX0 and 3.3 V; GPIO 10 (AXP2602 interrupt) and 23 (LCD reset) are in use

  • I2C / UART connector — GPIO 2, 3 (SDA, SCL) · 4-pin connector

    Also TX0 / RX0; I2C is the bus shared with touch and the AXP2602

Good to know before you start

  • Not in the LCD Ultra Pro editor yet.
  • Needs ESP-IDF 5.3+ for ESP32-C5 support.
  • Touch is optional; check which version you ordered.

What it is good for

  • •5 GHz Wi-Fi tools and monitors
  • •Battery-powered status displays
  • •Trying out the ESP32-C5

LVGL support in LCD Ultra Pro™

This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.

Arduino IDE settings

From the manufacturer's documentation (not tested by us yet)

BoardESP32C5 (the manufacturer writes “ESP32C5 (or Generic ESP32C5)”)
Flash Size16MB
PSRAMEnabled (Quad QIO)

Board package: esp32 by Espressif Systems 3.x

Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source

Frequently asked questions

What is special about the ESP32-C5?

It supports dual-band Wi-Fi 6 on 2.4 and 5 GHz, which earlier ESP32 chips do not.

Does the T-Display-C5 have touch?

Optionally: a CST816S capacitive touch version is available.

Which pin controls the backlight?

GPIO 25, with PWM.

Sources

Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):

More in the LilyGO T-Display family

Tools for this board

All free tools →

Connect sensors and parts

All sensors and parts →

Last updated:

Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.

Something wrong on this page?

Tell me what you found. I check every report and fix the page.