LilyGO · ESP32-S3 · 1.64" · 280×456
LilyGO T-Display-S3 AMOLED 1.64" specifications
This page collects the pinout, free GPIOs and hardware details of the LilyGO T-Display-S3 AMOLED 1.64". The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
280×456 is a tall, narrow AMOLED, close to the shape of a fitness band screen, and LilyGO's T-Display-S3 AMOLED 1.64 puts it on a compact ESP32-S3R8 board with an FT3168 touch layer. LilyGO names the panel driver as ICNA3311, also sold as CO5300.
The QSPI wiring is straightforward: CS on GPIO 10, clock on 12, data on 11, 13, 14 and 15, reset on 17 and a display power enable on 16. Touch and the SY6970 charger share an I2C bus on GPIO 7 (SDA) and 6 (SCL), with touch reset on 8 and interrupt on 9. Battery voltage reads on GPIO 4.
One quirk is worth knowing before you power it. LilyGO warns that the SY6970's output is unstable when the board runs from 5 V with no battery attached, and suggests a fix in its README. If the screen flickers on USB power alone, that's the first thing I'd check.

- Screen
- 1.64" · 280×456
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.64-inch AMOLED, 280×456, QSPI
- ICNA3311 / CO5300 panel driver
- FT3168 capacitive touch
- ESP32-S3R8, 16 MB flash, 8 MB octal PSRAM
- SY6970 battery charger
Specifications
| Manufacturer | LilyGO |
|---|---|
| Screen size | 1.64" |
| Resolution | 280×456 px |
| Colour depth | 16-bit |
| Display controller | ICNA3311 / CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | FT3168 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | V1.0 (2024-04-08). SY6970 charger on the I2C bus; LilyGO notes its output is unstable on 5 V without a battery connected. |
| Display | 280×456 AMOLED, QSPI: CS 10, CLK 12, D0 11, D1 13, D2 14, D3 15, RST 17, power enable 16 |
| Touch | FT3168, INT 9, RST 8 |
| I2C | SDA 7, SCL 6 (touch, charger) |
| Battery | SY6970 charger, voltage on GPIO 4 |
| Hardware version | V1.0 (2024-04-08) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | Header GPIO |
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | Battery voltage (ADC) |
| GPIO 5 | Header GPIO |
| GPIO 6 | I2C SCL (touch, charger) |
| GPIO 7 | I2C SDA (touch, charger) |
| GPIO 8 | Touch reset |
| GPIO 9 | Touch interrupt |
| GPIO 10 | LCD CS |
| GPIO 11 | LCD data 0 |
| GPIO 12 | LCD QSPI clock |
| GPIO 13 | LCD data 1 |
| GPIO 14 | LCD data 2 |
| GPIO 15 | LCD data 3 |
| GPIO 16 | Display power enable |
| GPIO 17 | LCD reset |
| GPIO 18 | Header GPIO |
| GPIO 21 | Header GPIO |
| GPIO 38 | Header GPIO |
| GPIO 39 | Header GPIO |
| GPIO 40 | Header GPIO |
| GPIO 41 | Header GPIO |
| GPIO 42 | Header GPIO |
| GPIO 43 | UART0 TX (header, UART connector) |
| GPIO 44 | UART0 RX (header, UART connector) |
| GPIO 45 | Header GPIO |
| GPIO 46 | Header GPIO |
| GPIO 47 | Header GPIO |
| GPIO 48 | Header GPIO |
Source: github.com, wiki.lilygo.cc, github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 1 | GPIO, PWM, ADC | On the side pin header (P6) |
| GPIO 2 | GPIO, PWM, ADC | On the side pin header (P6) |
| GPIO 3 | GPIO, PWM, ADC | On the side pin header (P6) |
| GPIO 5 | GPIO, PWM, ADC | On the side pin header (P6) |
| GPIO 21 | GPIO, PWM | On the side pin header (P6) |
| GPIO 38 | GPIO, PWM | On the side pin header (P6) |
| GPIO 39 | GPIO, PWM | On the side pin header (P6) |
| GPIO 40 | GPIO, PWM | On the side pin header (P6) |
| GPIO 41 | GPIO, PWM | On the side pin header (P6) |
| GPIO 42 | GPIO, PWM | On the side pin header (P6) |
| GPIO 45 | GPIO, PWM | On the side pin header (P6) |
| GPIO 46 | GPIO, PWM | On the side pin header (P6) |
| GPIO 47 | GPIO, PWM | On the side pin header (P6) |
| GPIO 48 | GPIO, PWM | On the side pin header (P6) |
| GPIO 18 | GPIO, PWM, ADC | On the side pin header (P6) |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the header and UART connector |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the header and UART connector |
- Pin header (P6) — GPIO 1, 2, 3, 5, 21, 38, 39, 40, 41, 42, 45, 46, 47, 48, 18, 43, 44, 6, 7 · 2.54 mm pin header
GPIO 6 / 7 are the I2C bus shared with touch and the charger; also VBUS
- I2C / UART connectors — GPIO 7, 6, 43, 44 (SDA, SCL, TX, RX) · 4-pin connectors
3.3 V supply
Good to know before you start
- It's not in the LCD Ultra Pro editor yet, so there's no export for it.
- Without a battery, the charger output can be unstable on 5 V. See the README note.
- The examples target Arduino-ESP32 2.0.14 and PlatformIO espressif32 6.5.0.
What it is good for
- •Band-style wearables
- •Narrow status displays
- •AMOLED UI experiments
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB Mode | Hardware CDC and JTAG |
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display driver does the T-Display-S3 AMOLED 1.64 use?
LilyGO lists the ICNA3311, also known as CO5300, driven over QSPI.
What touch controller does it have?
An FT3168 on I2C (GPIO 7/6), interrupt on GPIO 9 and reset on GPIO 8.
Is it the same as the T-Display-S3 AMOLED 1.91?
No. The 1.64 has a different panel (280×456), a different driver and touch as standard.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Xinyuan-LilyGO/T-Display-S3-AMOLED-1.64
- https://wiki.lilygo.cc/products/t-display-series/t-display-s3-amoled-1.64/
- https://github.com/Xinyuan-LilyGO/T-Display-S3-AMOLED-1.64/blob/main/project/T-Display-AMOLED-1.64_V1.0.pdf
- https://github.com/Xinyuan-LilyGO/T-Display-S3-AMOLED-1.64#readme
More in the LilyGO T-Display family
Tools for this board
- LilyGO T-Display-S3 AMOLED 1.64" Arduino IDE settings
- LilyGO T-Display-S3 AMOLED 1.64" pin planner
- LilyGO T-Display-S3 AMOLED 1.64" side-by-side comparison
- LilyGO T-Display-S3 AMOLED 1.64" LVGL memory estimate
- LilyGO T-Display-S3 AMOLED 1.64" I2C address check
- Other ESP32 boards with the ICNA3311
- Other ESP32 boards with the CO5300
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.