Waveshare · ESP32-C6 · 1.64" · 280×456
Waveshare ESP32-C6-Touch-AMOLED-1.64 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-C6-Touch-AMOLED-1.64. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Tall and narrow, 280×456 on 1.64 inches, the AMOLED on this board has the shape of a fitness band. Waveshare drives it with a CO5300 over QSPI and puts an FT6146 touch controller on top, all on an ESP32-C6 with Wi-Fi 6, Bluetooth 5 and Zigbee / Thread.
The board keeps things simple: a QMI8658 IMU for motion, a 3.7 V battery connector with charging, a microSD slot, and PWR and BOOT buttons on the side, where BOOT can be used by your code. There are two SKUs. The plain one ships without headers, the -M version has them soldered.
Brightness is a modest 350 cd/m². I'd also keep expectations realistic on graphics: the C6 has no PSRAM, so full-screen images and long animations are hard work. The pin table below comes from Waveshare's schematic; the example files in the repository disagree with each other, so I wouldn't take pin numbers from them.

- Screen
- 1.64" · 280×456
- Chip
- ESP32-C6
- Memory
- 16 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 1.64-inch AMOLED, 280×456
- CO5300 QSPI, FT6146 touch
- ESP32-C6: Wi-Fi 6, Zigbee, Thread
- QMI8658 IMU
- Battery charging, microSD
- Header and header-less versions
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.64" |
| Resolution | 280×456 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | FT6146 (capacitive, I2C) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | QMI8658 IMU, battery charging, microSD, PWR and BOOT buttons; the -M version (SKU 34056) has a soldered header. The display shares three QSPI lines with the microSD slot. |
| Display | 280×456 AMOLED, CO5300 (QSPI), 350 cd/m² |
| Touch | FT6146 (I2C) |
| Sensors | QMI8658 six-axis IMU |
| Memory | 16 MB flash, no PSRAM |
| Versions | SKU 34055 (no header), 34056 (-M, header soldered) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Header GPIO |
| GPIO 1 | Touch interrupt |
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | LCD data 0 / microSD MOSI |
| GPIO 5 | LCD data 1 / microSD MISO |
| GPIO 6 | Header GPIO |
| GPIO 7 | LCD data 2 |
| GPIO 8 | I2C SCL (touch, IMU, header) |
| GPIO 9 | BOOT button (header) |
| GPIO 10 | LCD CS |
| GPIO 11 | LCD QSPI clock / microSD SCK |
| GPIO 12 | USB D- (header) |
| GPIO 13 | USB D+ (header) |
| GPIO 15 | microSD CS |
| GPIO 16 | UART0 TX (header) |
| GPIO 17 | UART0 RX (header) |
| GPIO 18 | I2C SDA (touch, IMU, header) |
| GPIO 19 | LCD data 3 |
| GPIO 20 | LCD reset |
| GPIO 21 | IMU interrupt |
| GPIO 22 | Display power enable |
| GPIO 23 | LCD tearing effect (TE, also on the header) |
Source: github.com, docs.waveshare.com, github.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 0 | GPIO, PWM, ADC | On the pin header |
| GPIO 2 | GPIO, PWM, ADC | On the pin header |
| GPIO 3 | GPIO, PWM, ADC | On the pin header |
| GPIO 6 | GPIO, PWM, ADC | On the pin header |
| GPIO 16 | GPIO, UART_TX | UART0 TX on the pin header |
| GPIO 17 | GPIO, UART_RX | UART0 RX on the pin header |
- Pin header (-M version) — GPIO 0, 2, 3, 6, 9, 23, 8, 18, 12, 13, 16, 17 · pin header
GPIO 8 / 18 are the on-board I2C bus; GPIO 23 carries the display TE signal
Good to know before you start
- It's not in the LCD Ultra Pro editor yet.
- The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
- GPIO 0, 2, 3 and 6 are free on the header of the -M version.
What it is good for
- •Band-style wearables
- •Zigbee remotes
- •Narrow status displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the resolution?
280×456 pixels on a 1.64-inch AMOLED.
Which touch controller is used?
An FT6146 on I2C.
What does -M mean?
The -M version comes with soldered pin headers.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/waveshareteam/ESP32-C6-Touch-AMOLED-1.64
- https://docs.waveshare.com/ESP32-C6-Touch-AMOLED-1.64
- https://www.waveshare.com/esp32-c6-touch-amoled-1.64.htm
- https://github.com/waveshareteam/ESP32-C6-Touch-AMOLED-1.64/blob/main/hardware/schematics/ESP32-C6-Touch-AMOLED-1.64-schematic.pdf
- https://docs.waveshare.com/ESP32-C6-Touch-AMOLED-1.64/Arduino
More in the Waveshare AMOLED family
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-Touch-AMOLED-1.8
- Waveshare ESP32-S3-AMOLED-1.91
- Waveshare ESP32-C6-Touch-AMOLED-2.06
- Waveshare ESP32-S3-Touch-AMOLED-2.06
- Waveshare ESP32-C6-Touch-AMOLED-2.16
- Waveshare ESP32-S3-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.