Waveshare · ESP32-S3 · 2.06" · 410×502
Waveshare ESP32-S3-Touch-AMOLED-2.06 specifications
This page collects the pinout and hardware details of the ESP32-S3-Touch-AMOLED-2.06. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
At 410×502 this is one of the sharpest small screens you can put on an ESP32-S3, and Waveshare packages it as a watch-shaped board. The 2.06-inch AMOLED uses a CO5300 controller on QSPI, the same family the newer 1.8-inch board switched to.
Memory is generous: 32 MB of flash according to the README, plus 8 MB of PSRAM. You'll want both. A full frame at 410×502 in RGB565 is around 400 KB, and AMOLED watch faces tend to be image-heavy.
Audio is a two-chip setup: an ES7210 with two digital microphones for input and an ES8311 codec for the speaker, which is switched on by GPIO 46. Power runs through an AXP2101 with battery charging, and a QMI8658 IMU handles wrist gestures. Unlike the 1.8, this board brings the LCD reset (GPIO 8) and touch reset (GPIO 9) out to real GPIOs.

- Screen
- 2.06" · 410×502
- Chip
- ESP32-S3
- Memory
- 32 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.06-inch AMOLED, 410×502, CO5300 (QSPI)
- FT3168 capacitive touch
- ESP32-S3: 32 MB flash, 8 MB PSRAM
- Dual digital microphones, ES7210 + ES8311
- AXP2101 PMU, QMI8658 IMU
- microSD slot
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 2.06" |
| Resolution | 410×502 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | FT3168 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 32 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Watch-style board. AXP2101 PMU (also switches the display power), QMI8658 IMU, PCF85063 RTC, ES8311 codec, ES7210 ADC with two digital microphones. BOOT on GPIO 0, PWR on GPIO 10. |
| Display | 410×502 AMOLED, CO5300: D0-D3 GPIO 4 to 7, CLK 11, CS 12, RST 8 |
| Touch | FT3168, INT 38, RST 9 |
| Audio | MCLK 16, SCLK 41, LRCLK 45, DOUT 40, DIN 42, amplifier 46 |
| I2C | SDA 15, SCL 14 |
| microSD | CMD 1, CLK 2, D0 3 |
| Power | AXP2101 with lithium charging |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | microSD MOSI |
| GPIO 2 | microSD SCK |
| GPIO 3 | microSD MISO |
| GPIO 4 | LCD data 0 |
| GPIO 5 | LCD data 1 |
| GPIO 6 | LCD data 2 |
| GPIO 7 | LCD data 3 |
| GPIO 8 | LCD reset |
| GPIO 9 | Touch reset |
| GPIO 10 | PWR button |
| GPIO 11 | LCD QSPI clock |
| GPIO 12 | LCD CS |
| GPIO 13 | LCD tearing effect (TE) |
| GPIO 14 | I2C SCL (touch, PMU, IMU, RTC, codecs) |
| GPIO 15 | I2C SDA (touch, PMU, IMU, RTC, codecs) |
| GPIO 16 | I2S MCLK |
| GPIO 17 | microSD CS |
| GPIO 21 | IMU interrupt |
| GPIO 38 | Touch interrupt |
| GPIO 39 | RTC interrupt |
| GPIO 40 | I2S data out (ES8311) |
| GPIO 41 | I2S SCLK |
| GPIO 42 | I2S data in (ES7210) |
| GPIO 45 | I2S LRCLK |
| GPIO 46 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- This watch board is in the wiki but not in the LCD Ultra Pro editor yet.
- AMOLED has no backlight pin. Dim it with a panel command.
- Burn-in is a real risk with static watch faces. Move or dim them.
What it is good for
- •Smartwatch firmware experiments
- •Voice-controlled wearables
- •Image-heavy round-cornered UIs
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 32MB (to match the 32 MB flash on the board) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the resolution of the ESP32-S3-Touch-AMOLED-2.06?
410×502 pixels on a CO5300 AMOLED controller.
How much flash does it have?
The README lists 32 MB of flash and 8 MB of PSRAM.
Which touch controller is used?
An FT3168 on I2C, interrupt on GPIO 38 and reset on GPIO 9.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare AMOLED family
- Waveshare ESP32-C6-Touch-AMOLED-1.64
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-Touch-AMOLED-1.8
- Waveshare ESP32-S3-AMOLED-1.91
- Waveshare ESP32-C6-Touch-AMOLED-2.06
- Waveshare ESP32-C6-Touch-AMOLED-2.16
- Waveshare ESP32-S3-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.