Waveshare · ESP32-S3 · 1.8" · 368×448
Waveshare ESP32-S3-Touch-AMOLED-1.8 specifications
This page collects the pinout and hardware details of the ESP32-S3-Touch-AMOLED-1.8. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Same board name, two different displays. Waveshare switched the ESP32-S3-Touch-AMOLED-1.8 to a new panel in 2026: V1 has an SH8601 driver with FT3168 touch, V2 a CO5300 with CST820 touch. The label on the back tells you which one you have, and it decides which driver your code needs.
Either way it's a 368×448 AMOLED on QSPI (GPIO 4 to 7 for data, 11 for clock, 12 for CS). AMOLED means true black and no backlight pin: brightness is a command to the panel. A TCA9554 I/O expander also sits on the shared I2C bus at GPIO 14/15.
The rest is a familiar Waveshare watch-board kit: an AXP2101 power manager with battery charging, a PCF85063 clock, a QMI8658 IMU, an ES8311 codec with microphone and speaker amplifier, and a microSD slot.

- Screen
- 1.8" · 368×448
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.8-inch AMOLED, 368×448, QSPI
- V1: SH8601 + FT3168, V2: CO5300 + CST820
- AXP2101 PMU with battery charging
- ES8311 codec, microphone, speaker amplifier
- PCF85063 RTC, QMI8658 IMU
- microSD slot
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.8" |
| Resolution | 368×448 px |
| Colour depth | 16-bit |
| Display controller | SH8601 (V1) / CO5300 (V2), QSPI AMOLED |
| Display interface | QSPI |
| Touch | FT3168 (V1) / CST820 (V2), capacitive, I2C |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | V1 uses an SH8601 panel with FT3168 touch, V2 (shipping from 2026-05-30) a CO5300 panel with CST820 touch; the label on the back tells them apart. A TCA9554 IO expander sits on the I2C bus. AXP2101 PMU, PCF85063 RTC, QMI8658 IMU, ES8311 codec. 7 GPIO pads at 1.27 mm pitch (numbers published only as an image). |
| Display | 368×448 AMOLED, QSPI: D0-D3 GPIO 4 to 7, CLK 11, CS 12 |
| Touch | FT3168 (V1) or CST820 (V2), interrupt GPIO 21 |
| I2C | SDA 15, SCL 14: touch, PMU, RTC, IMU, TCA9554, codec |
| Audio | MCLK 16, SCLK 9, LRCLK 45, DOUT 8, DIN 10, amplifier enable 46 |
| microSD | CMD 1, CLK 2, D0 3 |
| Memory | 16 MB flash, 8 MB PSRAM |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | microSD CMD |
| GPIO 2 | microSD CLK |
| GPIO 3 | microSD D0 |
| GPIO 4 | LCD data 0 |
| GPIO 5 | LCD data 1 |
| GPIO 6 | LCD data 2 |
| GPIO 7 | LCD data 3 |
| GPIO 8 | I2S data out (ES8311) |
| GPIO 9 | I2S SCLK |
| GPIO 10 | I2S data in (microphone) |
| GPIO 11 | LCD QSPI clock |
| GPIO 12 | LCD CS |
| GPIO 14 | I2C SCL (touch, PMU, RTC, IMU, IO expander, codec) |
| GPIO 15 | I2C SDA (touch, PMU, RTC, IMU, IO expander, codec) |
| GPIO 16 | I2S MCLK |
| GPIO 21 | Touch interrupt |
| GPIO 45 | I2S LRCLK |
| GPIO 46 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- Check V1 or V2 before you pick a display driver. They are not interchangeable.
- V1 is discontinued; boards shipped from late May 2026 are V2.
- There are 7 GPIO pads at 1.27 mm pitch. Waveshare shows their numbers only in a picture.
What it is good for
- •AMOLED smartwatch builds
- •Wearable voice assistants
- •High-contrast status displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | Waveshare ESP32-S3-Touch-AMOLED-1.8 |
|---|---|
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) for the examples with large image resources |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
How do I know if my AMOLED-1.8 is V1 or V2?
Look at the label on the back. V1 uses the SH8601 panel with FT3168 touch, V2 the CO5300 with CST820.
Where is the backlight pin?
There is none. AMOLED panels have no backlight; brightness is set by a command over QSPI.
Does it have a battery charger?
Yes, the AXP2101 PMU charges a 3.7 V lithium cell on the MX1.25 connector.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare AMOLED family
- Waveshare ESP32-C6-Touch-AMOLED-1.64
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-AMOLED-1.91
- Waveshare ESP32-C6-Touch-AMOLED-2.06
- Waveshare ESP32-S3-Touch-AMOLED-2.06
- Waveshare ESP32-C6-Touch-AMOLED-2.16
- Waveshare ESP32-S3-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.