Waveshare · ESP32-C6 · 2.16" · 480×480
Waveshare ESP32-C6-Touch-AMOLED-2.16 specifications
This page collects the pinout and hardware details of the ESP32-C6-Touch-AMOLED-2.16. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Square, 480×480, AMOLED, 600 cd/m². On paper the C6 version of Waveshare's 2.16-inch board has the same screen as the S3 version: a CO5300 on QSPI with a CST9220 touch controller. What changes is the chip, and with it what the board is good at.
The ESP32-C6 brings Wi-Fi 6, Bluetooth 5 and an 802.15.4 radio for Zigbee and Thread, which makes this a natural wall or desk controller in a smart-home mesh. It also brings 16 MB of flash and no PSRAM. A full 480×480 frame in RGB565 is about 450 KB, close to all of the C6's 512 KB internal SRAM, so the UI has to draw in partial buffers.
Around it: an AXP2101 power manager, a QMI8658 IMU, a PCF85063 clock, an ES8311 codec, an ES7210 dual-microphone ADC and speaker pads. The pin table below comes from Waveshare's interface drawing, not from the example code, which mixes in pin files from other boards.

- Screen
- 2.16" · 480×480
- Chip
- ESP32-C6
- Memory
- 16 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 2.16-inch square AMOLED, 480×480, 600 cd/m²
- CO5300 QSPI, CST9220 touch
- ESP32-C6: Wi-Fi 6, Zigbee, Thread
- ES8311 + ES7210 audio
- AXP2101, QMI8658, PCF85063
- BOOT, PWR and KEY buttons
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 2.16" |
| Resolution | 480×480 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | CST9220 (capacitive, I2C) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Square AMOLED, 600 cd/m². The LCD shares its clock and two data lines with the microSD slot; LCD reset and the speaker amplifier enable come from AXP2101 outputs (ALDO3 / ALDO2), not GPIOs. QMI8658 IMU, PCF85063 RTC, ES8311 codec, ES7210 dual-microphone ADC, BOOT / PWR / KEY buttons, IPEX antenna option. |
| Display | 480×480 AMOLED, CO5300 (QSPI), 600 cd/m² |
| Touch | CST9220 (I2C) |
| Audio | ES8311 codec, ES7210 ADC, dual microphones, speaker pads |
| Power | AXP2101, MX1.25 3.7 V battery connector |
| Memory | 16 MB flash, no PSRAM |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-C6-Touch-AMOLED-2.16, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | LCD QSPI clock / microSD SCK |
| GPIO 1 | LCD data 0 / microSD MOSI |
| GPIO 2 | LCD data 1 / microSD MISO |
| GPIO 3 | LCD data 2 |
| GPIO 4 | LCD data 3 |
| GPIO 5 | Touch interrupt |
| GPIO 6 | microSD CS |
| GPIO 7 | I2C SCL (touch, PMU, IMU, RTC, codecs) |
| GPIO 8 | I2C SDA (touch, PMU, IMU, RTC, codecs) |
| GPIO 9 | BOOT button |
| GPIO 10 | KEY button |
| GPIO 11 | Touch reset |
| GPIO 15 | LCD CS |
| GPIO 16 | IMU interrupt 1 |
| GPIO 17 | IMU interrupt 2 |
| GPIO 18 | PWR button |
| GPIO 19 | I2S MCLK |
| GPIO 20 | I2S SCLK |
| GPIO 21 | I2S ASDOUT (ES7210) |
| GPIO 22 | I2S LRCLK |
| GPIO 23 | I2S DSDIN (ES8311) |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
- An IPEX antenna option exists but needs a resistor moved.
What it is good for
- •Zigbee / Thread wall controllers
- •Voice-enabled smart-home panels
- •Square desk clocks
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Frequency | 80MHz |
| Flash Mode | QIO |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Is the C6 AMOLED-2.16 the same as the S3 version?
Same screen and touch chip, but the ESP32-C6 has Zigbee / Thread and no PSRAM.
Are any GPIOs free?
No. Every GPIO is used by the display, touch, audio, sensors or buttons; the LCD even shares its clock and two data lines with the microSD slot.
How bright is the screen?
Waveshare specifies 600 cd/m².
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare AMOLED family
- Waveshare ESP32-C6-Touch-AMOLED-1.64
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-Touch-AMOLED-1.8
- Waveshare ESP32-S3-AMOLED-1.91
- Waveshare ESP32-C6-Touch-AMOLED-2.06
- Waveshare ESP32-S3-Touch-AMOLED-2.06
- Waveshare ESP32-S3-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.