Waveshare · ESP32-C6 · 2.06" · 410×502
Waveshare ESP32-C6-Touch-AMOLED-2.06 specifications
This page collects the pinout and hardware details of the ESP32-C6-Touch-AMOLED-2.06. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
A watch-shaped AMOLED board where the radio matters more than raw speed. The 2.06-inch 410×502 panel is the same CO5300 screen Waveshare uses on its S3 watch board, but here it hangs off an ESP32-C6 with Wi-Fi 6, Bluetooth 5 and an 802.15.4 radio for Zigbee and Thread.
The pin map follows the C6 AMOLED-1.8 closely: QSPI on GPIO 0 (clock), 1 to 4 (data) and 5 (CS), I2C on GPIO 8 and 7, I2S audio on GPIO 19 to 23. This board adds proper reset lines: LCD reset on GPIO 11, touch reset on GPIO 10, touch interrupt on 15, and a speaker amplifier enable on GPIO 6.
An AXP2101 handles charging, a QMI8658 tracks motion and a PCF85063 keeps time. With 16 MB of flash and no PSRAM, a 410×502 screen is about the limit of what the C6 can drive comfortably.

- Screen
- 2.06" · 410×502
- Chip
- ESP32-C6
- Memory
- 16 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 2.06-inch AMOLED, 410×502, CO5300
- FT3168 capacitive touch
- ESP32-C6: Wi-Fi 6, Zigbee, Thread
- AXP2101 battery management
- QMI8658 IMU, PCF85063 RTC
- Microphone and speaker output
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 2.06" |
| Resolution | 410×502 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | FT3168 (capacitive, I2C) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Watch-style board. AXP2101 PMU (also switches the display power), QMI8658 IMU, PCF85063 RTC, ES8311 codec and ES7210 ADC with microphone, speaker output. BOOT on GPIO 9, PWR on GPIO 18. 16 MB flash, no PSRAM. |
| Display | 410×502 AMOLED: CLK 0, D0-D3 GPIO 1 to 4, CS 5, RST 11 |
| Touch | FT3168, INT 15, RST 10 |
| I2C | SDA 8, SCL 7 |
| Audio | MCLK 19, SCLK 20, LRCLK 22, DOUT 23, DIN 21, amplifier 6 |
| Memory | 16 MB flash, no PSRAM |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | LCD QSPI clock |
| GPIO 1 | LCD data 0 |
| GPIO 2 | LCD data 1 |
| GPIO 3 | LCD data 2 |
| GPIO 4 | LCD data 3 |
| GPIO 5 | LCD CS |
| GPIO 6 | Speaker amplifier enable |
| GPIO 7 | I2C SCL (touch, PMU, IMU, RTC, codec) |
| GPIO 8 | I2C SDA (touch, PMU, IMU, RTC, codec) |
| GPIO 9 | BOOT button |
| GPIO 10 | Touch reset |
| GPIO 11 | LCD reset |
| GPIO 15 | Touch interrupt |
| GPIO 16 | IMU interrupt 1 |
| GPIO 17 | IMU interrupt 2 |
| GPIO 18 | PWR button |
| GPIO 19 | I2S MCLK |
| GPIO 20 | I2S SCLK |
| GPIO 21 | I2S ASDOUT (ES7210) |
| GPIO 22 | I2S LRCLK |
| GPIO 23 | I2S DSDIN (ES8311) |
Source: github.com, docs.waveshare.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- The LCD Ultra Pro editor has no profile for this board yet.
- The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
- AMOLED has no backlight pin; dim the panel by command.
What it is good for
- •Smartwatches that control Zigbee devices
- •Thread-connected wearables
- •Low-power notification displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
Board package: esp32 by Espressif Systems 3.3.11
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the difference to the ESP32-S3-Touch-AMOLED-2.06?
Same panel, different chip: the C6 version has Wi-Fi 6, Zigbee and Thread but no PSRAM.
Which touch controller does it use?
An FT3168, interrupt on GPIO 15 and reset on GPIO 10.
Does it have audio?
Yes, an audio codec with microphone input and a speaker output; the amplifier is enabled on GPIO 6.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare AMOLED family
- Waveshare ESP32-C6-Touch-AMOLED-1.64
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-Touch-AMOLED-1.8
- Waveshare ESP32-S3-AMOLED-1.91
- Waveshare ESP32-S3-Touch-AMOLED-2.06
- Waveshare ESP32-C6-Touch-AMOLED-2.16
- Waveshare ESP32-S3-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.