Waveshare · ESP32-S3 · 2.16" · 480×480
Waveshare ESP32-S3-Touch-AMOLED-2.16 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-Touch-AMOLED-2.16. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Square AMOLED at 480×480 is rare. Most square ESP32 panels are IPS LCDs on an RGB bus, which eat two dozen GPIOs. The 2.16-inch board gets the same pixel count over a 4-line QSPI link to a CO5300 controller, leaving pins for audio and storage.
Touch is a CST9220, not the CST816 or FT3168 you see on Waveshare's smaller AMOLED boards, so check your touch driver first. Interrupt is on GPIO 11, reset on 40, and it shares the I2C bus at GPIO 14/15 with the AXP2101 PMU, the QMI8658 IMU and the ES8311 / ES7210 audio chips.
The display pins differ from the 1.8 and 2.06-inch boards too: clock on 38, reset on 39, CS 12, data on 4 to 7. The chip is an ESP32-S3R8 with 16 MB of flash and 8 MB of PSRAM, which is plenty for one full 480×480 frame buffer.

- Screen
- 2.16" · 480×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.16-inch square AMOLED, 480×480
- CO5300 controller over QSPI
- CST9220 capacitive touch
- AXP2101 PMU, QMI8658 IMU
- ES8311 codec and ES7210 ADC
- microSD slot
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 2.16" |
| Resolution | 480×480 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | CST9220 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | AXP2101 PMU, QMI8658 IMU, PCF85063 RTC, ES8311 codec and ES7210 ADC. ESP32-S3R8 with 16 MB flash and 8 MB PSRAM per the product page. |
| Display | 480×480 AMOLED, CO5300: D0-D3 GPIO 4 to 7, CLK 38, CS 12, RST 39 |
| Touch | CST9220, INT 11, RST 40 |
| Audio | MCLK 42, SCLK 9, LRCLK 45, DOUT 8, DIN 10, amplifier 46 |
| I2C | SDA 15, SCL 14 |
| microSD | CMD 1, CLK 2, D0 3 |
| Memory | ESP32-S3R8: 16 MB flash, 8 MB PSRAM |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-Touch-AMOLED-2.16, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 1 | microSD MOSI |
| GPIO 2 | microSD SCK |
| GPIO 3 | microSD MISO |
| GPIO 4 | LCD data 0 |
| GPIO 5 | LCD data 1 |
| GPIO 6 | LCD data 2 |
| GPIO 7 | LCD data 3 |
| GPIO 8 | I2S DSDIN (ES8311) |
| GPIO 9 | I2S SCLK |
| GPIO 10 | I2S ASDOUT (ES7210) |
| GPIO 11 | Touch interrupt |
| GPIO 12 | LCD CS |
| GPIO 13 | RTC interrupt |
| GPIO 14 | I2C SCL (touch, PMU, IMU, codecs) |
| GPIO 15 | I2C SDA (touch, PMU, IMU, codecs) |
| GPIO 16 | PWR button sense (SYS_OUT) |
| GPIO 17 | IMU interrupt 1 |
| GPIO 18 | Unassigned GPIO |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | IMU interrupt 2 |
| GPIO 38 | LCD QSPI clock |
| GPIO 39 | LCD reset |
| GPIO 40 | Touch reset |
| GPIO 41 | microSD CS |
| GPIO 42 | I2S MCLK |
| GPIO 43 | UART0 TX (OUT header) |
| GPIO 44 | UART0 RX (OUT header) |
| GPIO 45 | I2S LRCLK |
| GPIO 46 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, files.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 18 | GPIO, PWM, ADC | Not assigned in the schematic GPIO table |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the OUT pads |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the OUT pads |
- OUT pads — GPIO 43, 44 (TX, RX) · solder pads
Good to know before you start
- Not yet available in the LCD Ultra Pro editor.
- Pin numbers differ from the other Waveshare AMOLED boards. Copy configs with care.
- AMOLED has no backlight pin. Brightness is a panel command.
What it is good for
- •Square smart-home panels with deep blacks
- •Desk gadgets and clocks
- •Audio-reactive displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
Which touch controller does the AMOLED-2.16 use?
A CST9220 on I2C, with interrupt on GPIO 11 and reset on GPIO 40.
Is the 2.16-inch AMOLED round or square?
Square, 480×480 pixels.
Does it have audio?
Yes: an ES8311 codec for output, an ES7210 ADC for microphones and an amplifier enabled on GPIO 46.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/waveshareteam/ESP32-S3-Touch-AMOLED-2.16
- https://github.com/waveshareteam/Waveshare-ESP32-components
- https://www.waveshare.com/esp32-s3-touch-amoled-2.16.htm
- https://docs.waveshare.com/ESP32-S3-Touch-AMOLED-2.16
- https://files.waveshare.com/wiki/ESP32-S3-Touch-AMOLED-2.16/ESP32-S3-Touch-AMOLED-2.16-Schematic.pdf
More in the Waveshare AMOLED family
- Waveshare ESP32-C6-Touch-AMOLED-1.64
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-Touch-AMOLED-1.8
- Waveshare ESP32-S3-AMOLED-1.91
- Waveshare ESP32-C6-Touch-AMOLED-2.06
- Waveshare ESP32-S3-Touch-AMOLED-2.06
- Waveshare ESP32-C6-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.