Waveshare · ESP32-C6 · 1.8" · 368×448

Waveshare ESP32-C6-Touch-AMOLED-1.8 specifications

This page collects the pinout, free GPIOs and hardware details of the ESP32-C6-Touch-AMOLED-1.8. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.

This is the AMOLED-1.8 with a different brain. Where the S3 version has a fast dual-core chip with PSRAM, the C6 version trades that for Wi-Fi 6 and an 802.15.4 radio, so the same 368×448 screen can sit in a Zigbee or Thread network directly. The price is memory: 16 MB of flash and no PSRAM at all.

Waveshare's BSP puts the QSPI panel on GPIO 0 to 5 (clock 0, data 1 to 4, CS 5) and the shared I2C bus on GPIO 8 (SDA) and 7 (SCL). On that bus sit the touch controller, an AXP2101 power manager at 0x34, a QMI8658 IMU at 0x6B and a PCF85063 clock at 0x51. Touch interrupt is GPIO 15, and the microSD runs over SPI on GPIO 6, 10, 11 and 18.

Like the S3 board it exists in two revisions: V1 with an SH8601 panel and FT3168 or FT6146 touch, V2 with a CO5300 and CST820. Waveshare keeps separate Arduino example folders for each.

ESP32-C6-Touch-AMOLED-1.8 board diagram with an example screen: 1.8" 368×448, ESP32-C6
Annotated diagram of the Waveshare ESP32-C6-Touch-AMOLED-1.8, drawn by LCD Ultra Pro™.
Screen
1.8" · 368×448
Chip
ESP32-C6
Memory
16 MB flash, no PSRAM
Input
capacitive touch

Key features

  • 1.8-inch AMOLED, 368×448, QSPI
  • ESP32-C6: Wi-Fi 6, Bluetooth 5, Zigbee, Thread
  • AXP2101 PMU, QMI8658 IMU, PCF85063 RTC
  • I2S audio path
  • microSD over SPI
  • V1 and V2 panel revisions

Specifications

Waveshare ESP32-C6-Touch-AMOLED-1.8 technical specifications
ManufacturerWaveshare
Screen size1.8"
Resolution368×448 px
Colour depth16-bit
Display controllerSH8601 (V1) / CO5300 (V2), QSPI AMOLED
Display interfaceQSPI
TouchFT3168 / FT6146 (V1) or CST820 (V2), I2C
MicrocontrollerESP32-C6
ModuleESP32-C6
CPU clock160 MHz
Internal SRAM512 KB
PSRAMNone
Flash16 MB
Wi-FiYes
BluetoothYes
Hardware variantV1: SH8601 panel with FT3168 / FT6146 touch; V2: CO5300 with CST820 (separate Arduino example folders). AXP2101 PMU (0x34), QMI8658 IMU (0x6B), PCF85063 RTC (0x51). 16 MB flash, no PSRAM.
Display368×448 AMOLED: CLK 0, D0-D3 GPIO 1 to 4, CS 5
TouchFT3168 / FT6146 (V1, 0x38) or CST820 (V2, 0x15), INT 15
I2CSDA 8, SCL 7: touch, PMU, IMU, RTC
AudioMCLK 19, SCLK 20, LRCLK 22, DOUT 23, DIN 21
microSDCS 6, MOSI 10, SCK 11, MISO 18
Memory16 MB flash, no PSRAM

Board layout and connectors

Where each connector, button and LED sits on the Waveshare ESP32-C6-Touch-AMOLED-1.8, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.

Waveshare ESP32-C6-Touch-AMOLED-1.8 board layout: front with the screen, back with every connector, button and LED labelled
Annotated illustration © LCD Ultra Pro · connectors and labelled parts from the manufacturer’s board documentation; small parts simplified
Waveshare ESP32-C6-Touch-AMOLED-1.8 pinout guide: GPIO map, connectors with pin order, wiring example and wiring tips
Pinout guide for the Waveshare ESP32-C6-Touch-AMOLED-1.8. Open the full-size image to read the small print.

GPIO pinout

The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.

Waveshare ESP32-C6-Touch-AMOLED-1.8 GPIO pinout
GPIOFunction
GPIO 0LCD QSPI clock
GPIO 1LCD data 0
GPIO 2LCD data 1
GPIO 3LCD data 2
GPIO 4LCD data 3
GPIO 5LCD CS
GPIO 6microSD CS
GPIO 7I2C SCL (touch, PMU, IMU, RTC, codec)
GPIO 8I2C SDA (touch, PMU, IMU, RTC, codec)
GPIO 10microSD MOSI
GPIO 11microSD SCK
GPIO 12USB D- (header)
GPIO 13USB D+ (header)
GPIO 15Touch interrupt
GPIO 18microSD MISO
GPIO 19I2S MCLK
GPIO 20I2S SCLK
GPIO 21I2S data in
GPIO 22I2S LRCLK
GPIO 23I2S data out

Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.

Free GPIOs and connectors

These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.

Free GPIO pins of the Waveshare ESP32-C6-Touch-AMOLED-1.8
PinCapabilitiesNote
GPIO 12GPIO, PWMOn the header pads; USB D- (free if native USB is not used)
GPIO 13GPIO, PWMOn the header pads; USB D+ (free if native USB is not used)
  • Header pads — GPIO 7, 8, 12, 13 (SCL, SDA, USB D-, USB D+) · 12-pin pads

    Also 5 V, 3.3 V, GND, VBAT and UART TX / RX; I2C is the on-board bus

Good to know before you start

  • It's in the wiki only for now; the LCD Ultra Pro editor doesn't support it.
  • The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
  • Check V1 or V2 before choosing display and touch drivers.

What it is good for

  • •Zigbee or Thread remote controls
  • •Matter-style smart-home panels
  • •Wearables that talk to a home hub

LVGL support in LCD Ultra Pro™

This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.

Arduino IDE settings

From the manufacturer's documentation (not tested by us yet)

BoardESP32C6 Dev Module
Partition Scheme16M Flash (3MB APP/9.9MB FATFS) for the examples with large image resources

Board package: esp32 by Espressif Systems

Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source

Frequently asked questions

Does the ESP32-C6-Touch-AMOLED-1.8 have PSRAM?

No. It has 16 MB of flash and the ESP32-C6's internal SRAM only.

Can it join a Zigbee network?

Yes. The ESP32-C6 has an IEEE 802.15.4 radio for Zigbee 3.0 and Thread next to Wi-Fi 6.

How do V1 and V2 differ?

V1 uses an SH8601 panel with FT3168 / FT6146 touch, V2 a CO5300 panel with CST820 touch.

Sources

Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):

More in the Waveshare AMOLED family

Tools for this board

All free tools →

Connect sensors and parts

All sensors and parts →

Last updated:

Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.

Something wrong on this page?

Tell me what you found. I check every report and fix the page.