Makerfabs · ESP32-S3 · 1.8" · 368×448
MaTouch ESP32-S3 AMOLED with Touch 1.8" (CHSC6417) specifications
This page collects the pinout and hardware details of the MaTouch ESP32-S3 AMOLED 1.8" (CHSC6417). The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Same outline, same resolution, different insides. The CHSC6417 version of Makerfabs' 1.8-inch AMOLED board uses a CO5300 panel driver and a CHSC6417 touch controller at I2C address 0x2E, and it moves almost every pin compared with the FT3168 version.
Here the QSPI display has CS on GPIO 12, clock 11, data on 9, 10, 6 and 5, reset 13 and a power enable on GPIO 7. Touch sits on I2C at GPIO 3 (SDA) and 4 (SCL), with interrupt 1 and reset 2. If you copy a config from the FT3168 board, nothing will light up.
The rest matches its sibling: ESP32-S3R8, a WS2812 LED, reset, boot and user buttons, a 3.7 V battery input and a 2×12 header at 1.27 mm pitch. The CO5300 is common on newer AMOLED boards, so drivers for it are easy to find.

- Screen
- 1.8" · 368×448
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.8-inch AMOLED, 368×448
- CO5300 QSPI driver
- CHSC6417 touch (I2C 0x2E)
- ESP32-S3R8
- WS2812 LED, user button
- 2×12 header at 1.27 mm
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 1.8" |
| Resolution | 368×448 px |
| Colour depth | 16-bit |
| Display controller | CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | CHSC6417 (capacitive, I2C 0x2E) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | 2 x 12 header at 1.27 mm pitch, WS2812 LED, reset / boot / user buttons, 3.7 V battery input, native USB. Different panel (CO5300), touch chip and pin map from the FT3168 version. |
| Display | 368×448 AMOLED, CO5300: CS 12, CLK 11, D0 9, D1 10, D2 6, D3 5, RST 13, power enable 7 |
| Touch | CHSC6417 at 0x2E, SDA 3, SCL 4, INT 1, RST 2 |
| Power | USB-C 5 V (native USB), 3.7 V battery input |
| Buttons | Reset, Boot, User |
| Header | 2×12, 1.27 mm pitch |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | Touch interrupt |
| GPIO 2 | Touch reset |
| GPIO 3 | I2C SDA (touch) |
| GPIO 4 | I2C SCL (touch) |
| GPIO 5 | LCD data 3 |
| GPIO 6 | LCD data 2 |
| GPIO 7 | Display power enable |
| GPIO 9 | LCD data 0 |
| GPIO 10 | LCD data 1 |
| GPIO 11 | LCD QSPI clock |
| GPIO 12 | LCD CS |
| GPIO 13 | LCD reset |
Source: github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not available in the LCD Ultra Pro editor yet.
- Pins differ from the FT3168 version. Check the name on your board.
- The CHSC6417 needs a driver that knows it. Makerfabs bundles one in its examples.
What it is good for
- •AMOLED watch faces
- •Small premium-looking dashboards
- •Battery gadgets
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
Which touch chip does this MaTouch AMOLED use?
A CHSC6417 at I2C address 0x2E, on GPIO 3 (SDA) and 4 (SCL).
Is it pin-compatible with the FT3168 version?
No. Display and touch pins are different.
Which display driver does it use?
A CO5300 over QSPI.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Makerfabs MaTouch family
- Makerfabs MaTouch 1.28" ToolSet Controller
- Makerfabs MaTouch ESP32-S3 Rotary IPS Display 1.28"
- Makerfabs MaTouch ESP32-S3 Round SPI TFT with Touch 1.28"
- MaTouch SmartKnob
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (FT3168)
- Makerfabs MaTouch ESP32-S3 AMOLED AI Camera
- Makerfabs MaTouch ESP32-S3 Rotary IPS 2.1 Round
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 2.4" ST7789
- MaTouch ESP32-S3 SPI TFT with AI 2.8"
- MaTouch ESP32-S3 SPI TFT with Touch 2.8"
- Makerfabs MaTouch ESP32-S3 SPI TFT with Touch 3.5"
- Makerfabs MaTouch ESP32-S3 MaUWB SPI TFT Touch 3.95" ST7796
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 3.95" ST7796
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.