Makerfabs · ESP32-S3 · 2.8" · 240×320
MaTouch ESP32-S3 SPI TFT with AI 2.8" (ST7789V) specifications
This page collects the pinout and hardware details of the MaTouch ESP32-S3 SPI TFT with AI 2.8". The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The AI in the name is about voice. Makerfabs ships this 2.8-inch board with examples for speech-to-text, text-to-speech and an AI voice assistant, so the hardware around the screen is a microphone, a speaker output and an RGB LED for status.
The screen itself is a 240×320 ST7789V on SPI (SCK 48, MOSI 13, MISO 12, CS 40, DC 21, backlight 45), sharing the bus with a microSD slot whose CS is GPIO 47. Touch is a GT911 with five points on I2C at GPIO 39/38, interrupt 14 and reset 18. The speaker path uses I2S on GPIO 1, 19 and 20, and a WS2812 LED sits on GPIO 0.
There are two USB-C ports, one through a USB-to-UART bridge and one on native USB, plus 16 MB of flash and 8 MB of PSRAM. The microphone pins differ between Makerfabs' examples, so I've left them out of the table.

- Screen
- 2.8" · 240×320
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.8-inch, 240×320, ST7789V (SPI)
- GT911 touch, 5 points
- Microphone and speaker output
- WS2812 RGB LED
- ESP32-S3, 16 MB flash, 8 MB PSRAM
- Two USB-C ports
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 2.8" |
| Resolution | 240×320 px |
| Colour depth | 16-bit |
| Display controller | ST7789V (SPI) |
| Display interface | SPI |
| Touch | GT911 (capacitive, 5 points, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Voice board: microphone and speaker output with Makerfabs examples for speech-to-text, text-to-speech and an AI voice assistant. Two USB-C ports (USB-to-UART and native USB). The microphone clock / data pins are left out because the examples define them in several ways. |
| Display | ST7789V: SCK 48, MOSI 13, MISO 12, CS 40, DC 21, backlight 45 |
| Touch | GT911, SDA 39, SCL 38, INT 14, RST 18 |
| Speaker | I2S WS 1, DOUT 19, BCLK 20 |
| LED | WS2812 on GPIO 0 |
| microSD | CS 47 on the display SPI bus |
Board layout and connectors
Where each connector, button and LED sits on the MaTouch ESP32-S3 SPI TFT with AI 2.8-inch (ST7789V), with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | WS2812 LED |
| GPIO 1 | Speaker I2S WS |
| GPIO 2 | Microphone I2S WS |
| GPIO 12 | SPI MISO |
| GPIO 13 | SPI MOSI (LCD, microSD) |
| GPIO 14 | Touch interrupt |
| GPIO 18 | Touch reset |
| GPIO 19 | Speaker I2S data out |
| GPIO 20 | Speaker I2S BCLK |
| GPIO 21 | LCD DC |
| GPIO 38 | I2C SCL (touch) |
| GPIO 39 | I2C SDA (touch) |
| GPIO 40 | LCD CS |
| GPIO 45 | Backlight |
| GPIO 47 | microSD CS |
| GPIO 48 | SPI SCK (LCD, microSD) |
Source: github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not supported by the LCD Ultra Pro editor yet.
- The WS2812 is on GPIO 0, the boot pin. Avoid driving it low at power-up.
- Microphone pins vary between the examples. Use the one your project starts from.
What it is good for
- •Voice assistants and chat bots
- •Spoken notifications
- •Smart-home voice remotes
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB(128MB) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Does the MaTouch AI 2.8" have a microphone?
Yes, and a speaker output. Makerfabs provides speech-to-text, text-to-speech and AI assistant examples.
Which touch controller is used?
A GT911 with five-point touch on I2C (GPIO 39/38).
How much memory does it have?
16 MB of flash and 8 MB of PSRAM.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Makerfabs MaTouch family
- Makerfabs MaTouch 1.28" ToolSet Controller
- Makerfabs MaTouch ESP32-S3 Rotary IPS Display 1.28"
- Makerfabs MaTouch ESP32-S3 Round SPI TFT with Touch 1.28"
- MaTouch SmartKnob
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (CHSC6417)
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (FT3168)
- Makerfabs MaTouch ESP32-S3 AMOLED AI Camera
- Makerfabs MaTouch ESP32-S3 Rotary IPS 2.1 Round
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 2.4" ST7789
- MaTouch ESP32-S3 SPI TFT with Touch 2.8"
- Makerfabs MaTouch ESP32-S3 SPI TFT with Touch 3.5"
- Makerfabs MaTouch ESP32-S3 MaUWB SPI TFT Touch 3.95" ST7796
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 3.95" ST7796
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.