Makerfabs · ESP32-S3 · 1.28" · 240×240
MaTouch SmartKnob (ESP32-S3) specifications
This page collects the pinout and hardware details of the MaTouch SmartKnob. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Most knobs click because of a spring. This one clicks because a motor tells it to. The MaTouch SmartKnob is Makerfabs' build of the open-source SmartKnob idea: a brushless gimbal motor under the knob, an MT6701 magnetic encoder that reads its angle, and firmware that turns that into detents, end stops or free spin on demand.
The motor phases come from GPIO 15, 16 and 17, and the MT6701 talks over GPIO 1, 2 and 42. On top sits a round 240×240 GC9A01 touch LCD on SPI (SCK 11, MOSI 12, CS 10, DC 14, reset 9, backlight 13), with touch on its own I2C pair at GPIO 6/8 and a push button on GPIO 5.
The brain is an ESP32-S3-WROOM-1U-N16R8 with 16 MB of flash and 8 MB of PSRAM, and there's an internal battery. Makerfabs is upfront that it's an open project for makers rather than a finished product, and I'd take that seriously: expect to tune motor parameters.

- Screen
- 1.28" · 240×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- Haptic feedback from a brushless gimbal motor
- MT6701 magnetic angle encoder
- Round 240×240 GC9A01 touch LCD
- ESP32-S3-WROOM-1U-N16R8
- Push button and internal battery
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 1.28" |
| Resolution | 240×240 px |
| Colour depth | 16-bit |
| Display controller | GC9A01 (SPI) |
| Display interface | SPI |
| Touch | Capacitive (I2C) |
| Rotary encoder | Yes |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1U-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Haptic knob: brushless gimbal motor with an MT6701 magnetic encoder gives programmable detents and end stops. Round 240x240 GC9A01 touch LCD, internal battery, USB-C. Makerfabs calls it an open project for makers, not a finished commercial product. Main board V1.5, display board V1.2. |
| Display | 240×240 round, GC9A01: SCK 11, MOSI 12, CS 10, DC 14, RST 9, backlight 13 |
| Touch | I2C SDA 6, SCL 8 |
| Motor | Phases on GPIO 17, 16, 15 |
| Encoder | MT6701: SDA 1, SCL 2, select 42 |
| Hardware | Main board V1.5, display board V1.2 |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | Magnetic encoder SDA (MT6701) |
| GPIO 2 | Magnetic encoder SCL (MT6701) |
| GPIO 5 | Push button |
| GPIO 6 | Touch I2C SDA |
| GPIO 8 | Touch I2C SCL |
| GPIO 9 | LCD reset |
| GPIO 10 | LCD CS |
| GPIO 11 | LCD SCK |
| GPIO 12 | LCD MOSI |
| GPIO 13 | Backlight |
| GPIO 14 | LCD DC |
| GPIO 15 | Motor phase 3 |
| GPIO 16 | Motor phase 2 |
| GPIO 17 | Motor phase 1 |
| GPIO 42 | Magnetic encoder select (MT6701) |
Source: github.com, www.makerfabs.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- The LCD Ultra Pro editor doesn't include the SmartKnob yet.
- Haptics need motor calibration. Plan time for tuning.
- Makerfabs calls it a maker project, not a finished consumer product.
What it is good for
- •Haptic volume and dimmer controls
- •Smart-home knobs with feedback
- •Learning motor control (FOC)
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
How does the MaTouch SmartKnob create clicks?
A brushless motor under the knob, controlled with feedback from an MT6701 magnetic encoder, simulates detents and end stops.
Which display does it use?
A round 240×240 GC9A01 LCD with capacitive touch.
Which chip does it run on?
An ESP32-S3-WROOM-1U-N16R8 with 16 MB of flash and 8 MB of PSRAM.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Makerfabs MaTouch family
- Makerfabs MaTouch 1.28" ToolSet Controller
- Makerfabs MaTouch ESP32-S3 Rotary IPS Display 1.28"
- Makerfabs MaTouch ESP32-S3 Round SPI TFT with Touch 1.28"
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (CHSC6417)
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (FT3168)
- Makerfabs MaTouch ESP32-S3 AMOLED AI Camera
- Makerfabs MaTouch ESP32-S3 Rotary IPS 2.1 Round
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 2.4" ST7789
- MaTouch ESP32-S3 SPI TFT with AI 2.8"
- MaTouch ESP32-S3 SPI TFT with Touch 2.8"
- Makerfabs MaTouch ESP32-S3 SPI TFT with Touch 3.5"
- Makerfabs MaTouch ESP32-S3 MaUWB SPI TFT Touch 3.95" ST7796
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 3.95" ST7796
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.