Makerfabs · ESP32-S3 · 1.8" · 368×448
MaTouch ESP32-S3 AMOLED with Touch 1.8" (FT3168) specifications
This page collects the pinout, free GPIOs and hardware details of the MaTouch ESP32-S3 AMOLED 1.8" (FT3168). The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Makerfabs sells two 1.8-inch AMOLED boards with nearly the same name. This one is the FT3168 version: an SH8601 panel driver and an FT3168 touch controller at I2C address 0x38. The other uses a CO5300 and a CHSC6417, and its pins are completely different.
The 368×448 panel runs on QSPI with CS on GPIO 4, clock 5, data on 7, 10, 11 and 12, reset 40 and a display power enable on GPIO 9. Touch shares nothing with the display: it has its own I2C on GPIO 2 (SDA) and 1 (SCL), with the interrupt on 13.
The board has an ESP32-S3R8, a WS2812 LED, reset, boot and user buttons, a 3.7 V battery input and native USB. A 2×12 header at 1.27 mm pitch brings out the remaining I/O. That pitch is finer than standard jumper wires, so plan for a matching connector or an adapter.

- Screen
- 1.8" · 368×448
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.8-inch AMOLED, 368×448
- SH8601 QSPI driver
- FT3168 touch (I2C 0x38)
- ESP32-S3R8
- WS2812 LED, user button
- 2×12 header at 1.27 mm
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 1.8" |
| Resolution | 368×448 px |
| Colour depth | 16-bit |
| Display controller | SH8601 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | FT3168 (capacitive, I2C 0x38) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | 2 x 12 header at 1.27 mm pitch, WS2812 LED, reset / boot / user buttons, 3.7 V battery input, native USB. Sister board of the CHSC6417 version, which has a different panel, touch chip and pins. |
| Display | 368×448 AMOLED, SH8601: CS 4, CLK 5, D0 7, D1 10, D2 11, D3 12, RST 40, power enable 9 |
| Touch | FT3168 at 0x38, SDA 2, SCL 1, INT 13 |
| Power | USB-C 5 V (native USB), 3.7 V battery input |
| Buttons | Reset, Boot, User |
| Header | 2×12, 1.27 mm pitch |
Board layout and connectors
Where each connector, button and LED sits on the MaTouch ESP32-S3 AMOLED with Touch 1.8-inch (FT3168), with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | I2C SCL (touch) |
| GPIO 2 | I2C SDA (touch) |
| GPIO 4 | LCD CS |
| GPIO 5 | LCD QSPI clock |
| GPIO 7 | LCD data 0 |
| GPIO 9 | Display power enable |
| GPIO 10 | LCD data 1 |
| GPIO 11 | LCD data 2 |
| GPIO 12 | LCD data 3 |
| GPIO 13 | Touch interrupt |
| GPIO 15 | Header GPIO |
| GPIO 16 | Header GPIO |
| GPIO 17 | Header GPIO |
| GPIO 18 | Header GPIO |
| GPIO 21 | Header GPIO |
| GPIO 38 | Header GPIO |
| GPIO 39 | Header GPIO |
| GPIO 40 | LCD reset |
| GPIO 41 | Header GPIO |
| GPIO 42 | Header GPIO |
| GPIO 43 | UART0 TX (header) |
| GPIO 44 | UART0 RX (header) |
| GPIO 45 | Header GPIO |
| GPIO 46 | Header GPIO |
| GPIO 47 | Header GPIO |
| GPIO 48 | Header GPIO |
Source: github.com, www.makerfabs.com, github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 15 | GPIO, PWM, ADC | On the 2 x 12 1.27 mm header (J2) |
| GPIO 16 | GPIO, PWM, ADC | On the 2 x 12 1.27 mm header (J2) |
| GPIO 17 | GPIO, PWM, ADC | On the 2 x 12 1.27 mm header (J2) |
| GPIO 18 | GPIO, PWM, ADC | On the 2 x 12 1.27 mm header (J2) |
| GPIO 21 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 38 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 39 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 41 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 42 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 45 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 46 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 47 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 48 | GPIO, PWM | On the 2 x 12 1.27 mm header (J2) |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the J2 header |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the J2 header |
- 2 x 12 header (J2) — GPIO 2, 1, 15, 16, 17, 18, 21, 38, 39, 41, 42, 45, 46, 47, 48, 43, 44 · 2 x 12 pin, 1.27 mm
GPIO 2 / 1 are the touch I2C bus (SDA / SCL); also VBUS and 3.3 V
Good to know before you start
- The LCD Ultra Pro editor has no profile for this board yet.
- Don't confuse it with the CHSC6417 version. Different driver, touch chip and pins.
- AMOLED: brightness is a panel command, not a backlight pin.
What it is good for
- •Wearable prototypes
- •High-contrast status displays
- •AMOLED UI experiments
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32-S3 (the board type isn't named; these are the other Tools settings in the example) |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 16MB(128Mb) |
| Partition Scheme | 16M Flash(3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display driver is on the MaTouch AMOLED 1.8" FT3168?
An SH8601 over QSPI, 368×448 pixels.
What is the touch address?
The FT3168 answers at I2C address 0x38 on GPIO 2 (SDA) and 1 (SCL).
How do I tell the two 1.8" versions apart?
By the touch chip in the name: FT3168 (this board, SH8601 panel) or CHSC6417 (CO5300 panel).
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Makerfabs/MaTouch-ESP32-S3-AMOLED-with-Touch-1.8-FT3168
- https://www.makerfabs.com/matouch-esp32-s3-amoled-with-touch-1-8-ft3168.html
- https://github.com/Makerfabs/MaTouch-ESP32-S3-AMOLED-with-Touch-1.8-FT3168/blob/main/hardware/MaTouch_ESP32-S3%20AMOLED%20with%20Touch%201.8''%20FT3168%20V1.0.pdf
- https://github.com/Makerfabs/MaTouch-ESP32-S3-AMOLED-with-Touch-1.8-FT3168#readme
More in the Makerfabs MaTouch family
- Makerfabs MaTouch 1.28" ToolSet Controller
- Makerfabs MaTouch ESP32-S3 Rotary IPS Display 1.28"
- Makerfabs MaTouch ESP32-S3 Round SPI TFT with Touch 1.28"
- MaTouch SmartKnob
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (CHSC6417)
- Makerfabs MaTouch ESP32-S3 AMOLED AI Camera
- Makerfabs MaTouch ESP32-S3 Rotary IPS 2.1 Round
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 2.4" ST7789
- MaTouch ESP32-S3 SPI TFT with AI 2.8"
- MaTouch ESP32-S3 SPI TFT with Touch 2.8"
- Makerfabs MaTouch ESP32-S3 SPI TFT with Touch 3.5"
- Makerfabs MaTouch ESP32-S3 MaUWB SPI TFT Touch 3.95" ST7796
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 3.95" ST7796
Tools for this board
- MaTouch ESP32-S3 AMOLED 1.8" (FT3168) Arduino IDE settings
- MaTouch ESP32-S3 AMOLED 1.8" (FT3168) pin planner
- MaTouch ESP32-S3 AMOLED 1.8" (FT3168) side-by-side comparison
- MaTouch ESP32-S3 AMOLED 1.8" (FT3168) LVGL memory estimate
- MaTouch ESP32-S3 AMOLED 1.8" (FT3168) I2C address check
- Other ESP32 boards with the SH8601
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.