Makerfabs · ESP32-S3 · 2.8" · 240×320
MaTouch ESP32-S3 SPI TFT with Touch 2.8" (Camera) specifications
This page collects the pinout and hardware details of the MaTouch ESP32-S3 SPI TFT 2.8". The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
A camera board first, a display board second. The MaTouch ESP32-S3 SPI TFT 2.8 pairs a 240×320 ST7789 touch screen with an OV3660 sensor that captures up to 2048×1536, which is a step up from the OV2640 on many ESP32 camera boards.
The display uses SPI on GPIO 14 (clock), 13 (MOSI) and 12 (MISO), with CS 15, DC 21 and the backlight on GPIO 48. Touch is a GT911 with five points on I2C at GPIO 39/38 and interrupt 40. The microSD slot runs over SDMMC on GPIO 2, 41 and 42, which is handy for saving photos.
Makerfabs' face recognition examples run on it, helped by 16 MB of flash and 8 MB of PSRAM. There's a CH340K USB-to-UART port and a native USB port. The touch reset pin isn't the same in every example, so I'd check yours before relying on it.

- Screen
- 2.8" · 240×320
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.8-inch, 240×320, ST7789 (SPI)
- GT911 touch, 5 points
- OV3660 3 MP camera
- ESP32-S3, 16 MB flash, 8 MB PSRAM
- microSD over SDMMC
- CH340K and native USB
Specifications
| Manufacturer | Makerfabs |
|---|---|
| Screen size | 2.8" |
| Resolution | 240×320 px |
| Colour depth | 16-bit |
| Display controller | ST7789 (SPI) |
| Display interface | SPI |
| Touch | GT911 (capacitive, 5 points, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | OV3660 3 MP camera (up to 2048x1536). Two USB-C ports: CH340K USB-to-UART and native USB. One GPIO and one I2C expansion connector (shown by Makerfabs only as an image). The touch reset pin differs between examples, so it is left out. |
| Display | ST7789: SCK 14, MOSI 13, MISO 12, CS 15, DC 21, backlight 48 |
| Touch | GT911, SDA 39, SCL 38, INT 40 |
| Camera | OV3660, up to 2048×1536 |
| microSD | CMD 2, CLK 42, D0 41 |
| Temperature range | -40 to +85 °C |
Board layout and connectors
Where each connector, button and LED sits on the MaTouch ESP32-S3 SPI TFT with Touch 2.8-inch (Camera), with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 2 | microSD CMD |
| GPIO 12 | LCD MISO |
| GPIO 13 | LCD MOSI |
| GPIO 14 | LCD SCK |
| GPIO 15 | LCD CS |
| GPIO 21 | LCD DC |
| GPIO 38 | I2C SCL (touch) |
| GPIO 39 | I2C SDA (touch) |
| GPIO 40 | Touch interrupt |
| GPIO 41 | microSD D0 |
| GPIO 42 | microSD CLK |
| GPIO 48 | Backlight |
Source: github.com, wiki.makerfabs.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
- Expansion header — GPIO 39, 38 (SDA, SCL) · 2.54 mm pin header
I2C (shared with touch) plus the camera signals CSI D0-D5, D7, MCLK, PCLK, VSYNC, HSYNC, 3.3 V and GND; Makerfabs does not number the camera GPIOs
Good to know before you start
- This board is documented here but isn't in the LCD Ultra Pro editor yet.
- Camera and display together use most of the RAM bandwidth. Keep preview frames small.
- Expansion is one GPIO and one I2C connector.
What it is good for
- •Face recognition and door viewers
- •Photo capture to SD
- •Camera-based sensors
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which camera does the MaTouch SPI TFT 2.8" use?
An OV3660 with 3 megapixels, up to 2048×1536.
Is it the same as the MaTouch AI 2.8"?
No. The AI version has a microphone and speaker; this one has a camera and different display pins.
Which touch controller does it use?
A GT911 on I2C (GPIO 39/38), interrupt on GPIO 40.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Makerfabs MaTouch family
- Makerfabs MaTouch 1.28" ToolSet Controller
- Makerfabs MaTouch ESP32-S3 Rotary IPS Display 1.28"
- Makerfabs MaTouch ESP32-S3 Round SPI TFT with Touch 1.28"
- MaTouch SmartKnob
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (CHSC6417)
- MaTouch ESP32-S3 AMOLED with Touch 1.8" (FT3168)
- Makerfabs MaTouch ESP32-S3 AMOLED AI Camera
- Makerfabs MaTouch ESP32-S3 Rotary IPS 2.1 Round
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 2.4" ST7789
- MaTouch ESP32-S3 SPI TFT with AI 2.8"
- Makerfabs MaTouch ESP32-S3 SPI TFT with Touch 3.5"
- Makerfabs MaTouch ESP32-S3 MaUWB SPI TFT Touch 3.95" ST7796
- Makerfabs MaTouch Lite ESP32-S3 SPI Resistive Touch 3.95" ST7796
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.