Elecrow · ESP32-S3 · 1.28" · 240×240
Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display specifications
The CrowPanel 1.28" Rotary Display has its display and touch driver included in LCD Ultra Pro™: you design the LVGL screens and events at its exact 240×240 resolution without code, then export a complete Arduino project.
A knob you can also touch. The CrowPanel 1.28-inch Rotary Display puts a round 240×240 IPS screen inside a rotating ring, so you get two input methods on a device that fits in a palm: 48 × 48 × 33 mm and about 50 g.
The screen is a GC9A01 on SPI (SCK 10, MOSI 11, CS 9, DC 3, reset 14), and the CST816D touch controller has its own I2C bus on GPIO 6/7. The encoder phases land on GPIO 45 and 42, the push button on 41. A ring of five addressable LEDs behind the bezel is driven from GPIO 48 through a level shifter, which is handy for status colours.
Inside is an ESP32-S3R8 with 8 MB of PSRAM and 16 MB of flash. The board talks to the outside through a 12-pin FPC to a small base board with three 1.25 mm sockets: UART0, I2C and USB. The I2C port is separate from the touch bus, so GPIO 38/39 are yours.

- Screen
- 1.28" · 240×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.28-inch round IPS, 240×240, GC9A01
- CST816D capacitive touch
- Rotary encoder with push button
- Five addressable LEDs around the bezel
- ESP32-S3R8, 8 MB PSRAM, 16 MB flash
- Aluminium, plastic and acrylic housing
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 1.28" |
| Resolution | 240×240 px |
| Colour depth | 16-bit |
| Display controller | GC9A01 (SPI) |
| Display interface | SPI |
| Touch | CST816D (capacitive, I2C 0x15, own bus) + rotary encoder + push button |
| Rotary encoder | Yes |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.0 schematic (Elecrow). Round module in an aluminium and acrylic housing; the ports sit on a small base board connected through a 12-pin FPC. GPIO 4 and 12 also reach that FPC and two test pads. The LCD, its backlight and the touch controller run from a 3.3 V rail switched by GPIO 1: it must be HIGH before the display is initialised, otherwise the screen stays black. GPIO 2 switches the 5 V output of the UART and I2C ports; the Elecrow example sets it HIGH too. The backlight is on GPIO 46. |
| Display | 1.28-inch round IPS, 240×240, GC9A01 (SPI), backlight GPIO 46 |
| Touch | CST816D at 0x15, SDA 6, SCL 7, INT 5, RST 13 |
| Encoder | A on GPIO 45, B on GPIO 42, push on GPIO 41 |
| LEDs | Five addressable LEDs on GPIO 48, power LED on GPIO 40 |
| Ports | UART0, I2C (GPIO 38/39) and USB on 1.25 mm 4-pin sockets |
| Size | 48 × 48 × 33 mm, 50 g, 5 V / 1 A input |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel 1.28-inch ESP32-S3 Round Rotary Display, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | LCD + touch 3.3 V power switch (HIGH = on, before display init) |
| GPIO 2 | 5 V output switch for the UART and I2C ports (HIGH = on) |
| GPIO 3 | LCD DC |
| GPIO 5 | Touch interrupt |
| GPIO 6 | Touch I2C SDA |
| GPIO 7 | Touch I2C SCL |
| GPIO 9 | LCD CS |
| GPIO 10 | LCD SCK |
| GPIO 11 | LCD MOSI (SDA) |
| GPIO 13 | Touch reset |
| GPIO 14 | LCD reset |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 38 | I2C SDA (I2C port) |
| GPIO 39 | I2C SCL (I2C port) |
| GPIO 40 | Power LED (on = LOW) |
| GPIO 41 | Knob push button |
| GPIO 42 | Encoder B |
| GPIO 43 | UART0 TX (UART0 port) |
| GPIO 44 | UART0 RX (UART0 port) |
| GPIO 45 | Encoder A |
| GPIO 46 | Backlight (PWM, HIGH = on, after the LCD power switch) |
| GPIO 48 | LED ring data (5 WS2812 LEDs, level-shifted) |
Source: github.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 4 | GPIO, ADC, PWM | On the 12-pin FPC connector (pin 3) and a test pad |
| GPIO 12 | GPIO, ADC, PWM | On the 12-pin FPC connector (pin 4) and a test pad |
| GPIO 38 | GPIO, PWM | I2C SDA on the I2C port (1.25 mm 4-pin) |
| GPIO 39 | GPIO, PWM | I2C SCL on the I2C port (1.25 mm 4-pin) |
- UART0 port — GPIO 44, 43 (RX, TX) · 1.25 mm 4-pin
Level-shifted; also used for uploads
- I2C port — GPIO 39, 38 (SCL, SDA) · 1.25 mm 4-pin
Level-shifted; separate from the touch bus
- USB port — GPIO 19, 20 (D-, D+) · 1.25 mm 4-pin
Elecrow's wiki counts this socket as a second UART; on the schematic it carries GPIO 19/20, the native USB pins
Good to know before you start
- It isn't in the LCD Ultra Pro editor yet. This page documents the hardware.
- Uploads go through the base board. Keep the FPC cable seated, or the board looks dead.
- Five LEDs is not much light. Treat the ring as an indicator, not a lamp.
- Only two GPIOs are free (38/39 on the I2C port). Use I2C sensors.
What it is good for
- •Volume and dimmer knobs for Home Assistant
- •Thermostat-style controllers
- •Timer and menu dials
LVGL support in LCD Ultra Pro™
| Driver status | Matched to the manufacturer’s official demo, compile-tested |
|---|---|
| Arduino export | Complete LVGL 8.4 project with the display driver |
| USB Live preview | No |
| Orientations | 0° |
| Brightness control | Hardware backlight dimming |
Pick this board in the editor and the canvas matches its exact resolution and shape. Build the interface with widgets, add events without code, try it in Live Preview, then export it as a ready-to-compile Arduino project. See the documentation for the workflow.
Frequently asked questions
Which display driver does the CrowPanel 1.28 knob use?
A GC9A01 over SPI. Elecrow's factory code sets it up with LovyanGFX.
Does the knob press?
Elecrow lists a confirmation button that works as the knob press switch; on the schematic it reads on GPIO 41.
Can I connect sensors?
Yes, on the I2C port (GPIO 38 SDA, GPIO 39 SCL). It is a separate bus from the touch controller.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-11):
More in the Elecrow CrowPanel family
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.