Elecrow · ESP32-S3 · 3.5" · 320×480
Elecrow ESP Terminal 3.5" 16-bit Parallel specifications
This page collects the pinout, free GPIOs and hardware details of the Elecrow ESP Terminal 3.5" Parallel. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Elecrow calls it an RGB display. It isn't, at least not in the ESP32-S3 sense. The ILI9488 on this ESP Terminal is wired as a 16-bit 8080 parallel bus: data lines D0 to D15, plus WR on GPIO 18, RD on 48 and RS (DC) on 45. LovyanGFX's Bus_Parallel16 is what Elecrow's examples use, and it's a lot faster than SPI.
That speed costs pins. Sixteen data lines leave room for a microSD slot (GPIO 1, 2, 41, 42), a buzzer on GPIO 20, an FT6236 touch controller on the GPIO 38/39 I2C bus and the backlight on GPIO 46. The module is an ESP32-S3-WROOM-1-N16R8 with 16 MB flash and 8 MB PSRAM.
Four Crowtail ports remain. One carries UART0, one the I2C bus, and two are single GPIOs: GPIO 40 behind a level shifter and GPIO 19 at 3.3 V.

- Screen
- 3.5" · 320×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 3.5-inch TFT, 320×480, ILI9488
- 16-bit 8080 parallel bus
- FT6236 capacitive touch
- ESP32-S3-WROOM-1-N16R8
- microSD slot, buzzer
- Four Crowtail (HY2.0-4P) ports
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 3.5" |
| Resolution | 320×480 px |
| Colour depth | 16-bit |
| Display controller | ILI9488 (16-bit 8080 parallel) |
| Display interface | 16-bit 8080 parallel |
| Touch | FT6236 (capacitive, I2C 0x38) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V2.0 schematic (Elecrow). Elecrow sells it as an RGB display, but the panel is wired as a 16-bit 8080 parallel bus (D0-D15, WR, RD, RS). |
| Display | 3.5-inch, 320×480, ILI9488, 16-bit parallel (WR 18, RD 48, RS 45), backlight GPIO 46 |
| Touch | FT6236 at 0x38 on I2C GPIO 38/39 |
| Storage | microSD: CS 1, MOSI 2, MISO 41, SCK 42 |
| Ports | UART0, I2C, GPIO 40 (level-shifted), GPIO 19 |
| Power | 5 V, 500 mA |
| Size | 106 × 66 × 13 mm, active area 73.63 × 49.79 mm |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow ESP Terminal 3.5-inch 16-bit Parallel, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | microSD CS |
| GPIO 2 | microSD MOSI |
| GPIO 3 | LCD D8 |
| GPIO 4 | LCD D15 |
| GPIO 5 | LCD D14 |
| GPIO 6 | LCD D13 |
| GPIO 7 | LCD D12 |
| GPIO 8 | LCD D9 |
| GPIO 9 | LCD D7 |
| GPIO 10 | LCD D6 |
| GPIO 11 | LCD D5 |
| GPIO 12 | LCD D4 |
| GPIO 13 | LCD D3 |
| GPIO 14 | LCD D2 |
| GPIO 15 | LCD D11 |
| GPIO 16 | LCD D10 |
| GPIO 18 | LCD WR |
| GPIO 19 | Port GPIO (Crowtail) |
| GPIO 20 | Buzzer |
| GPIO 21 | LCD D1 |
| GPIO 38 | I2C SDA (touch, I2C port) |
| GPIO 39 | I2C SCL (touch, I2C port) |
| GPIO 40 | Port GPIO (Crowtail, level-shifted) |
| GPIO 41 | microSD MISO |
| GPIO 42 | microSD SCK |
| GPIO 43 | UART0 TX (UART port, USB serial) |
| GPIO 44 | UART0 RX (UART port, USB serial) |
| GPIO 45 | LCD RS (DC) |
| GPIO 46 | Backlight |
| GPIO 47 | LCD D0 |
| GPIO 48 | LCD RD |
Source: github.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 19 | GPIO, PWM, ADC | On a GPIO port (HY2.0-4P, 3.3 V) |
| GPIO 40 | GPIO, PWM | On a GPIO port (HY2.0-4P, level-shifted) |
- UART port — GPIO 44, 43 (RX, TX) · HY2.0-4P
Shares UART0 with the USB serial port
- I2C port — GPIO 39, 38 (SCL, SDA) · HY2.0-4P
Same bus as the FT6236 touch (0x38)
- GPIO port 1 — GPIO 40 · HY2.0-4P
Level-shifted, 5 V supply on the port
- GPIO port 2 — GPIO 19 · HY2.0-4P
3.3 V supply on the port
Good to know before you start
- You won't find it in the LCD Ultra Pro editor yet.
- Code for ESP32-S3 RGB panels (Bus_RGB) won't drive this screen. Use an 8080 parallel bus driver.
- The I2C port shares the bus with the touch controller at 0x38.
- Two free GPIOs, both on Crowtail ports.
- Elecrow's wiki asks for ESP32 Arduino core 2.0.14 or 2.0.15 and the libraries it provides. Newer cores may break the examples.
What it is good for
- •Fast 3.5-inch dashboards
- •Handheld terminals and data viewers
- •Learning projects with Crowtail modules
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Is the ESP Terminal 3.5 parallel an RGB display?
Not in the ESP32-S3 RGB-interface sense. The ILI9488 is driven over a 16-bit 8080 parallel bus with WR, RD and RS lines.
Which touch controller does it use?
An FT6236 at I2C address 0x38, on GPIO 38 (SDA) and GPIO 39 (SCL).
Which pins are free?
GPIO 40 (level-shifted) and GPIO 19 on the two GPIO Crowtail ports.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- Elecrow ESP Terminal 3.5" Parallel Arduino IDE settings
- Elecrow ESP Terminal 3.5" Parallel pin planner
- Elecrow ESP Terminal 3.5" Parallel side-by-side comparison
- Elecrow ESP Terminal 3.5" Parallel LVGL memory estimate
- Elecrow ESP Terminal 3.5" Parallel I2C address check
- Other ESP32 boards with the ILI9488
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.