Elecrow · ESP32-S3 · 1.46" · 360×360
Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel 1.46" ESP32-S3 Rotary Display. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
360×360 on 1.46 inches is a noticeably sharper circle than the 240×240 of the smaller CrowPanel knob, and that's the main reason to pick this one. Small text and thin arc gauges look clean instead of jagged.
Elecrow's factory code drives the panel over plain SPI with a LovyanGFX class it calls ST77961. The panel's own datasheet, which ships in the repo, names the controller JD9855 and the touch chip CST816D. Either way, the wiring is simple: SCK 10, MOSI 11, CS 9, DC 3, reset 14, backlight 46.
The rest mirrors the 1.28-inch knob. Encoder A and B on GPIO 45/42, the push switch on 41, an addressable LED ring (eight LEDs this time) on GPIO 48, and UART0, I2C and USB on 1.25 mm sockets. New here is a battery connector with charging. The charge status reads on GPIO 15, the battery voltage on GPIO 18. The housing is plastic and acrylic, 60 × 60 × 27.5 mm.

- Screen
- 1.46" · 360×360
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.46-inch round IPS, 360×360
- JD9855 controller over SPI, CST816D touch
- Rotary encoder with push switch
- Eight addressable LEDs
- Battery connector with charge status and voltage sense
- ESP32-S3R8, 8 MB PSRAM, 16 MB flash
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 1.46" |
| Resolution | 360×360 px |
| Colour depth | 16-bit |
| Display controller | JD9855 (SPI) |
| Display interface | SPI |
| Touch | CST816D (capacitive, I2C 0x15, own bus) |
| Rotary encoder | Yes |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.0 schematic (Elecrow). Adds a 1.25 mm battery connector with charging (status on GPIO 15, voltage on GPIO 18). The panel datasheet names JD9855 as the display controller. |
| Display | 1.46-inch round IPS, 360×360, JD9855 (SPI) |
| Touch | CST816D, I2C on GPIO 6/7, INT 5, RST 13 |
| Encoder | A GPIO 45, B GPIO 42, push GPIO 41 |
| Battery | Charge status GPIO 15, voltage GPIO 18 (ADC) |
| Ports | UART0, I2C (GPIO 38/39), USB on ZX-MX 1.25-4P |
| Size | 60 × 60 × 27.5 mm, 60 g |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel 1.46-inch ESP32-S3 Round Rotary Display, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 3 | LCD DC |
| GPIO 5 | Touch interrupt |
| GPIO 6 | Touch I2C SDA |
| GPIO 7 | Touch I2C SCL |
| GPIO 9 | LCD CS |
| GPIO 10 | LCD SCK |
| GPIO 11 | LCD MOSI |
| GPIO 13 | Touch reset |
| GPIO 14 | LCD reset |
| GPIO 15 | Battery charge status |
| GPIO 18 | Battery voltage (ADC) |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 38 | I2C SDA (I2C port) |
| GPIO 39 | I2C SCL (I2C port) |
| GPIO 40 | Power LED |
| GPIO 41 | Knob push button |
| GPIO 42 | Encoder B |
| GPIO 43 | UART0 TX (UART0 port) |
| GPIO 44 | UART0 RX (UART0 port) |
| GPIO 45 | Encoder A |
| GPIO 46 | Backlight |
| GPIO 48 | LED ring data (8 addressable LEDs) |
Source: github.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 38 | GPIO, PWM | I2C SDA on the I2C port (1.25 mm 4-pin) |
| GPIO 39 | GPIO, PWM | I2C SCL on the I2C port (1.25 mm 4-pin) |
- UART0 port — GPIO 44, 43 (RX, TX) · 1.25 mm 4-pin
Level-shifted; also used for uploads
- I2C port — GPIO 39, 38 (SCL, SDA) · 1.25 mm 4-pin
Level-shifted; separate from the touch bus
- USB port — GPIO 19, 20 (D-, D+) · 1.25 mm 4-pin
On the schematic it carries GPIO 19/20, the native USB pins
Good to know before you start
- The LCD Ultra Pro editor has no profile for this knob yet.
- Elecrow's wiki recommends ESP32 Arduino core 2.0.14. Later versions may need code changes.
- If your library has no ST77961 or JD9855 class, Elecrow's bundled LovyanGFX copy has one.
- GPIO 38/39 on the I2C port are the only free pins.
What it is good for
- •Sharp round gauges and dials
- •Portable knob remotes on battery
- •Smart-home scene selectors
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB |
| Partition Scheme | elecrow_s3 (Elecrow’s own scheme from the course) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the display controller of the CrowPanel 1.46?
The panel datasheet in Elecrow's repo lists JD9855. The factory code calls its LovyanGFX class ST77961.
Can it run from a battery?
Yes. There is a battery connector with charging; the charge status is on GPIO 15 and the battery voltage on GPIO 18.
How many LEDs are in the ring?
Eight addressable LEDs, driven from GPIO 48.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-1.46inch-HMI-ESP32-Rotary-Display
- https://www.elecrow.com/wiki/CrowPanel_1.46-inch-HMI_ESP32_Rotary_Display_360x360_IPS_Round_Touch_Knob_Screen.html
- https://www.elecrow.com/crowpanel-1-46inch-hmi-esp32-rotary-display-360-360-ips-round-touch-knob-screen.html
- https://www.elecrow.com/wiki/1.46_inch_Rotary_Display_Arduino_Course_Index.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel 1.46" ESP32-S3 Rotary Display Arduino IDE settings
- CrowPanel 1.46" ESP32-S3 Rotary Display pin planner
- CrowPanel 1.46" ESP32-S3 Rotary Display side-by-side comparison
- CrowPanel 1.46" ESP32-S3 Rotary Display LVGL memory estimate
- Other ESP32 boards with the JD9855
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.