Elecrow · ESP32-P4 · 10.1" · 1024×600
Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel Advanced 10.1" ESP32-P4. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
A 10.1-inch ESP32 panel used to mean a slow RGB bus and a lot of compromise. The ESP32-P4 changes that: two MIPI-DSI lanes, a hardware 2D engine and 32 MB of PSRAM give LVGL at 1024×600 a lot more headroom than an ESP32-S3 ever had.
This is the largest board in Elecrow's Advanced P4 line. It shares the pin map of the 7 and 9-inch versions: GT911 touch on GPIO 45/46, LCD reset 41, backlight PWM on 31, microSD on 39/43/44, and an ESP32-C6-MINI-1 on SDIO for Wi-Fi 6 and Bluetooth 5. Audio is an I2S amplifier for a 4 Ω 3 W speaker plus a PDM microphone on GPIO 24/26, and the backlight has a separate power-enable line on GPIO 29.
What you'll actually wire to is the 2×12 header with eleven free GPIOs, the UART1 and I2C ports, and the level-shifted UART3-IN terminal, which also accepts 5 V power. A MIPI-CSI connector takes Elecrow's optional 2 MP camera.

- Screen
- 10.1" · 1024×600
- Chip
- ESP32-P4
- Memory
- 16 MB flash, 32 MB PSRAM (OPI/HPI)
- Input
- capacitive touch
Key features
- 10.1-inch IPS, 1024×600, MIPI-DSI
- GT911 touch, up to 5 points
- ESP32-P4: 400 MHz RISC-V, 32 MB PSRAM
- PDM microphone, 3 W speaker amplifier
- Wi-Fi 6 / Bluetooth 5 via ESP32-C6
- 11 free GPIOs on a 2×12 header
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 10.1" |
| Resolution | 1024×600 px |
| Colour depth | 24-bit |
| Display controller | EK79007 (MIPI-DSI, 2 lanes) |
| Display interface | MIPI-DSI |
| Touch | GT911 (capacitive, I2C, address 0x5D or 0x14) |
| Microcontroller | ESP32-P4 |
| Module | ESP32-P4NRW32 + ESP32-C6-MINI-1 (Wi-Fi 6 / Bluetooth 5 co-processor over SDIO) |
| CPU clock | 400 MHz |
| Internal SRAM | 768 KB |
| PSRAM | 32 MB (OPI/HPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Pin map per the Elecrow wiki for hardware V1.2. Audio: I2S speaker amplifier (4 ohm 3 W speaker, PH2.0-2P) and a PDM microphone; the wiki lists no audio codec. Backlight: power enable on GPIO 29, PWM on GPIO 31. V1.1 reversed the ESP32-C6 SDIO data lines (D0-D3 = GPIO 17-14, was 14-17) and added 4-wire SDIO. V1.2 swapped GPIO 27/28 and 53/54 between the wireless-module socket and the GPIO header. With the screen on the board draws 8-10 W, so a PC USB port alone may not be enough. |
| Display | 10.1-inch IPS, 1024×600, MIPI-DSI 2-lane (EK79007 driver in the examples) |
| Touch | GT911 (0x5D or 0x14), I2C GPIO 45/46, RST 40, INT 42 |
| Audio | I2S amplifier on GPIO 21 to 23 (control 30), PDM mic on GPIO 24/26 |
| Camera | MIPI-CSI connector, camera I2C on GPIO 12/13, reset GPIO 11 |
| Ports | GPIO header (2×12), UART1, I2C, UART3-IN, microSD, battery |
| Size | 248 × 147 mm |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 2 | GPIO header |
| GPIO 3 | GPIO header |
| GPIO 4 | GPIO header |
| GPIO 5 | GPIO header |
| GPIO 6 | Wireless module SPI MOSI |
| GPIO 7 | Wireless module SPI MISO |
| GPIO 8 | Wireless module SPI SCK |
| GPIO 9 | Wireless module: SX1262 BUSY / nRF24 IRQ |
| GPIO 10 | Wireless module: SX1262 NSS (chip select) |
| GPIO 11 | Camera reset |
| GPIO 12 | Camera I2C SDA |
| GPIO 13 | Camera I2C SCL |
| GPIO 14 | ESP32-C6 SDIO D3 (V1.1+; D0 on V1.0) |
| GPIO 15 | ESP32-C6 SDIO D2 (V1.1+; D1 on V1.0) |
| GPIO 16 | ESP32-C6 SDIO D1 (V1.1+; D2 on V1.0) |
| GPIO 17 | ESP32-C6 SDIO D0 (V1.1+; D3 on V1.0) |
| GPIO 18 | ESP32-C6 SDIO CLK |
| GPIO 19 | ESP32-C6 SDIO CMD |
| GPIO 21 | I2S LRCK (speaker amplifier) |
| GPIO 22 | I2S BCLK (speaker amplifier) |
| GPIO 23 | I2S data out (speaker amplifier) |
| GPIO 24 | PDM microphone clock |
| GPIO 25 | GPIO header |
| GPIO 26 | PDM microphone data |
| GPIO 27 | Wireless module: SX1262 IRQ / nRF24 CE (V1.2; GPIO 53 on V1.0/V1.1) |
| GPIO 28 | Wireless module: SX1262 reset / nRF24 CSN (V1.2; GPIO 54 on V1.0/V1.1) |
| GPIO 29 | Backlight power enable (LCD_BK_POWER) |
| GPIO 30 | Speaker amplifier control |
| GPIO 31 | Backlight enable (PWM) |
| GPIO 32 | ESP32-C6 enable / reset |
| GPIO 33 | UART3 RX (UART3-IN terminal) |
| GPIO 34 | UART3 TX (UART3-IN terminal) |
| GPIO 35 | BOOT button |
| GPIO 37 | UART0 TX (USB serial) |
| GPIO 38 | UART0 RX (USB serial) |
| GPIO 39 | microSD D0 |
| GPIO 40 | Touch reset |
| GPIO 41 | LCD reset |
| GPIO 42 | Touch interrupt |
| GPIO 43 | microSD CLK |
| GPIO 44 | microSD CMD |
| GPIO 45 | I2C SDA (touch, I2C port) |
| GPIO 46 | I2C SCL (touch, I2C port) |
| GPIO 47 | UART1 TX (UART1 port) |
| GPIO 48 | UART1 RX (UART1 port) |
| GPIO 49 | GPIO header |
| GPIO 50 | GPIO header |
| GPIO 51 | GPIO header |
| GPIO 52 | GPIO header |
| GPIO 53 | GPIO header |
| GPIO 54 | GPIO header |
Source: github.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 2 | GPIO, PWM | On the 2 x 12 GPIO header |
| GPIO 3 | GPIO, PWM | On the 2 x 12 GPIO header |
| GPIO 4 | GPIO, PWM | On the 2 x 12 GPIO header |
| GPIO 5 | GPIO, PWM | On the 2 x 12 GPIO header |
| GPIO 25 | GPIO, PWM | On the 2 x 12 GPIO header |
| GPIO 49 | GPIO, PWM, ADC | On the 2 x 12 GPIO header |
| GPIO 50 | GPIO, PWM, ADC | On the 2 x 12 GPIO header |
| GPIO 51 | GPIO, PWM, ADC | On the 2 x 12 GPIO header |
| GPIO 52 | GPIO, PWM, ADC | On the 2 x 12 GPIO header |
| GPIO 53 | GPIO, PWM, ADC | On the 2 x 12 GPIO header (V1.2; on V1.0/V1.1 this pin goes to the wireless-module socket and GPIO 27 is on the header) |
| GPIO 54 | GPIO, PWM, ADC | On the 2 x 12 GPIO header (V1.2; on V1.0/V1.1 this pin goes to the wireless-module socket and GPIO 28 is on the header) |
| GPIO 47 | GPIO, PWM | UART1 TX on the UART1 port (HY2.0-4P) |
| GPIO 48 | GPIO, PWM | UART1 RX on the UART1 port (HY2.0-4P) |
- GPIO header — GPIO 2, 3, 4, 5, 25, 49, 50, 51, 52, 53, 54 · 2 x 12-pin female
Also carries 3.3 V, 5 V and GND. Pin list is for V1.2; V1.0/V1.1 have GPIO 27/28 here instead of 53/54
- UART1 port — GPIO 48, 47 (RX, TX) · HY2.0-4P
3.3 V output, 1 A max
- I2C port — GPIO 46, 45 (SCL, SDA) · HY2.0-4P
Level-shifted; same bus as the GT911 touch. 3.3 V output, 1 A max
- UART3-IN terminal — GPIO 34, 33 (TX, RX) · XH2.54-4P
Level-shifted, also a 5 V (+/-5 %, 2 A max) power input
- Wireless module header — GPIO 6, 7, 8, 9, 10, 27, 28 · 2 x 7-pin female
SPI (SCK 8, MISO 7, MOSI 6) plus SX1262 or nRF24 control lines. Pin list is for V1.2; V1.0/V1.1 use GPIO 53/54 instead of 27/28. 3.3 V, 1 A max
Good to know before you start
- You can't pick this board in the LCD Ultra Pro editor yet. The specs are here so you can plan.
- V1.0, V1.1 and V1.2 each have their own tutorial set, because the radio wiring changed between them: V1.1 reversed the SDIO data lines, V1.2 swapped GPIO 27/28 with 53/54. Check the label on the PCB before you pick one.
- Wi-Fi runs on the ESP32-C6 with Elecrow's factory firmware. The wiki says it can't be reprogrammed through the P4.
- Big screen, big supply. It draws 8 to 10 W with the screen on, which one PC USB port can't always deliver; connect the second USB port as well.
What it is good for
- •Main control panels for a house or workshop
- •Video doorbell and camera viewers
- •Kiosks and information boards
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32P4 Dev Module |
|---|---|
| Flash Frequency | 80MHz |
| Flash Mode | QIO |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | Enabled |
| Upload Mode | UART0 / Hardware CDC |
| USB Mode | Hardware CDC and JTAG |
Board package: esp32 by Espressif Systems 3.3.3 (or the version the course package names)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which GPIO pins can I use on the CrowPanel Advanced 10.1?
On V1.2: GPIO 2, 3, 4, 5, 25 and 49 to 54 on the 2×12 header, and GPIO 47/48 on the UART1 port. Older V1.0 and V1.1 boards have GPIO 27/28 where V1.2 has 53/54.
Does the 10.1-inch board have a speaker amplifier?
Yes. The wiki lists an on-board amplifier for a 4 Ω 3 W speaker on a PH2.0 connector, fed over I2S on GPIO 21 to 23, with GPIO 30 switching the amp.
Which LVGL version should I use?
LVGL 8.3 if you start from Elecrow's lessons. The Arduino sketches bundle 8.3.11, and the ESP-IDF projects ask for lvgl ^8.3.11 with esp_lvgl_port 2.6. The SquareLine Studio example is the exception: it uses LVGL 9.3.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-Advanced-10.1inch-ESP32-P4-HMI-AI-Display-1024x600-IPS-Touch-Screen
- https://www.elecrow.com/wiki/CrowPanel_Advanced_10.1inch_ESP32-P4_HMI_AI_Display_1024x600_IPS.html
- https://www.elecrow.com/crowpanel-advanced-10-1inch-esp32-p4-hmi-ai-display-1024x600-ips-touch-screen-wifi-6.html
- https://www.elecrow.com/wiki/P4_Arduino_01_Print_Hello_World.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
Tools for this board
- CrowPanel Advanced 10.1" ESP32-P4 Arduino IDE settings
- CrowPanel Advanced 10.1" ESP32-P4 pin planner
- CrowPanel Advanced 10.1" ESP32-P4 side-by-side comparison
- CrowPanel Advanced 10.1" ESP32-P4 LVGL memory estimate
- CrowPanel Advanced 10.1" ESP32-P4 I2C address check
- Other ESP32 boards with the EK79007
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.