Elecrow · ESP32-S3 · 2.1" · 480×480
Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display specifications
This page collects the pinout and hardware details of the CrowPanel 2.1" Rotary Display. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Where did all the GPIOs go? On the 2.1-inch CrowPanel knob, into the display. The 480×480 round panel is an ST7701S on a 16-bit RGB bus, and with clock, sync and a 3-wire SPI init line it uses 23 pins of the ESP32-S3R8.
Elecrow solves the shortage with a PCF8574 I/O expander at I2C address 0x21. Panel reset, power, the touch interrupt and the knob's push button all sit on it, so you read the button over I2C. The encoder phases stay on real GPIOs: A on 42, B on 4.
Touch is a CST826 at 0x15, sharing the GPIO 38/39 bus with the expander. Backlight is PWM on GPIO 6. The 8 MB of PSRAM is used as it should be here: Elecrow's demo allocates full-size LVGL buffers in PSRAM and uses DMA bounce buffers for the RGB panel. The housing is 79 × 79 × 30 mm and weighs about 80 g.

- Screen
- 2.1" · 480×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.1-inch round IPS, 480×480
- ST7701S on 16-bit RGB with 3-wire SPI init
- CST826 capacitive touch
- Rotary encoder; push button via PCF8574
- ESP32-S3R8, 8 MB PSRAM, 16 MB flash
- Aluminium, plastic and acrylic housing
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 2.1" |
| Resolution | 480×480 px |
| Colour depth | 16-bit |
| Display controller | ST7701S (RGB + 3-wire SPI init) |
| Display interface | RGB565 parallel + 3-wire SPI init |
| Touch | CST826 (capacitive, I2C 0x15) |
| Rotary encoder | Yes |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.0 schematic (Elecrow). Reset, power, touch interrupt and the knob push button go through a PCF8574 I/O expander at I2C address 0x21, so they are not ESP32 GPIOs. |
| Display | 2.1-inch round IPS, 480×480, ST7701S, RGB (PCLK 41, DE 40, HSYNC 15, VSYNC 7) |
| Panel init | 3-wire SPI: CS 16, SCK 2, SDA 1 |
| Touch | CST826 at 0x15 on I2C GPIO 38/39 |
| Expander | PCF8574 at 0x21: reset, power, touch interrupt, knob push |
| Encoder | A GPIO 42, B GPIO 4 |
| Size | 79 × 79 × 30 mm, 80 g, 5 V / 1 A |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel 2.1-inch ESP32-S3 Round Rotary Display, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT |
| GPIO 1 | LCD init SPI SDA |
| GPIO 2 | LCD init SPI SCK |
| GPIO 3 | LCD R1 |
| GPIO 4 | Encoder B |
| GPIO 5 | LCD B0 |
| GPIO 6 | Backlight (PWM) |
| GPIO 7 | LCD VSYNC |
| GPIO 8 | LCD R2 |
| GPIO 9 | LCD G5 |
| GPIO 10 | LCD G4 |
| GPIO 11 | LCD G3 |
| GPIO 12 | LCD G2 |
| GPIO 13 | LCD G1 |
| GPIO 14 | LCD G0 |
| GPIO 15 | LCD HSYNC |
| GPIO 16 | LCD init SPI CS |
| GPIO 17 | LCD R4 |
| GPIO 18 | LCD R3 |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | LCD B4 |
| GPIO 38 | I2C SDA (touch, PCF8574 expander, I2C port) |
| GPIO 39 | I2C SCL (touch, PCF8574 expander, I2C port) |
| GPIO 40 | LCD DE |
| GPIO 41 | LCD PCLK |
| GPIO 42 | Encoder A |
| GPIO 43 | UART0 TX |
| GPIO 44 | UART0 RX |
| GPIO 45 | LCD B1 |
| GPIO 46 | LCD R0 |
| GPIO 47 | LCD B3 |
| GPIO 48 | LCD B2 |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
- 12-pin FPC (power, UART0, I2C, USB, reset, BOOT) — GPIO 44, 43, 39, 38, 19, 20, 0 · 0.5 mm 12-pin FPC
Leads to the base board with 1.25 mm sockets; Elecrow's wiki lists them as UART0, UART1 and I2C, the schematic routes GPIO 19/20 (native USB) to one of them
Good to know before you start
- Wiki only for now: the LCD Ultra Pro editor doesn't support this knob yet.
- There are no free GPIOs. External parts go on the I2C bus, next to the touch and the expander.
- The ST7701S needs its init sequence over SPI before the RGB stream works. Use the one from the factory code.
- The knob press is an I2C read, not an interrupt pin. Poll it.
What it is good for
- •Large round control dials
- •Smart thermostats and climate panels
- •Media controllers with album art
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | elecrow_s3 (10.0MB APP with OTA/1.31MB SPIFFS) |
| PSRAM | OPI PSRAM |
| Upload Mode | UART0 / Hardware CDC |
| USB Mode | Hardware CDC and JTAG |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which touch controller does the CrowPanel 2.1 use?
A CST826 at I2C address 0x15, on GPIO 38 (SDA) and 39 (SCL).
Where is the encoder button connected?
To the PCF8574 I/O expander at address 0x21, not to an ESP32 pin. The encoder phases are on GPIO 42 and 4.
Is the 2.1 knob the same as the 1.28 and 1.46?
No. It uses an RGB panel with an ST7701S and an I/O expander, so the pin map is completely different.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-2.1inch-HMI-ESP32-Rotary-Display-480-480-IPS-Round-Touch-Knob-Screen
- https://www.elecrow.com/crowpanel-2-1inch-hmi-esp32-rotary-display-480-480-ips-round-touch-knob-screen.html
- https://www.elecrow.com/wiki/CrowPanel_2.1inch-HMI_ESP32_Rotary_Display_480_IPS_Round_Touch_Knob_Screen.html
- https://www.elecrow.com/wiki/2.1_Lesson01-Print_Hello_World.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.