Elecrow · ESP32-S3 · 2.4" · 320×240
Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel Advance 2.4" ESP32-S3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Check the resolution first. Elecrow's own README for this board says 800×480, which is wrong: the panel is 320×240, and the factory LovyanGFX config sets up an ST7789 at exactly that size. A small thing, but it's the kind of error that sends people hunting for a driver that doesn't exist.
Past that, the Advance 2.4 packs a lot into a small panel. There's an ESP32-S3-WROOM-1-N16R8 (16 MB flash, 8 MB PSRAM), a capacitive touch layer on I2C, an IPS screen rated at 400 cd/m², a MEMS microphone, an I2S speaker amplifier, a buzzer and a microSD slot. On the back sits a two-row header for Elecrow's plug-in radio modules, such as ESP32-H2 or nRF2401 boards.
Two USB-C ports is the other detail people miss. One goes through a CH340K to UART0 for uploads, the other is the ESP32-S3's native USB on GPIO 19 and 20.
The spare I/O is thin. UART1 on GPIO 17/18 is the only port the board doesn't use itself, and the I2C port shares its bus with the touch controller.

- Screen
- 2.4" · 320×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.4-inch IPS, 320×240, ST7789 over SPI
- Capacitive touch on I2C (0x38)
- ESP32-S3-WROOM-1-N16R8: 16 MB flash, 8 MB PSRAM
- Microphone, I2S speaker amplifier and buzzer
- microSD slot and a header for Elecrow radio modules
- Two USB-C ports: USB-serial and native USB
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 2.4" |
| Resolution | 320×240 px |
| Colour depth | 16-bit |
| Display controller | ST7789 (SPI) |
| Display interface | SPI |
| Touch | FT6336U (capacitive, I2C 0x38) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.2 schematic (Elecrow). V1.1 changed the amplifier (GPIO 21 mute) and the microphone pins; V1.2 only changed the buttons. The manufacturer README lists 800*480, but the panel and the factory code are 320x240. On V1.0 the microphone used three lines: data GPIO 10, WS GPIO 3, clock GPIO 9. |
| Display | 2.4-inch IPS, 320×240, ST7789 (SPI), 400 cd/m² typ. |
| Touch | Capacitive, I2C on GPIO 15/16, interrupt GPIO 47, reset GPIO 48 |
| Audio | MEMS microphone (GPIO 9/10), I2S amplifier (GPIO 11/12/13), mute on GPIO 21, buzzer on GPIO 8 |
| Storage | microSD over SPI (GPIO 4/5/6/7) |
| Ports | UART1 and I2C (HY2.0-4P), UART0 terminal (XH2.54-4P), battery (PH2.0, 3.7 to 4.2 V), speaker (PH2.0) |
| Size | 77.1 × 51.8 × 15.8 mm |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel Advance 2.4-inch ESP32-S3 HMI, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button / wireless module CS |
| GPIO 1 | Wireless module header (TXD2) |
| GPIO 2 | Wireless module header (RXD2) |
| GPIO 3 | Wireless module SPI MOSI (V1.0: also microphone WS) |
| GPIO 4 | microSD MISO |
| GPIO 5 | microSD SCK |
| GPIO 6 | microSD MOSI |
| GPIO 7 | microSD CS |
| GPIO 8 | Buzzer |
| GPIO 9 | Microphone clock / wireless module MISO (selected by GPIO 45) |
| GPIO 10 | Microphone data / wireless module SPI CLK (selected by GPIO 45) |
| GPIO 11 | Speaker amplifier I2S LRCLK |
| GPIO 12 | Speaker amplifier I2S data |
| GPIO 13 | Speaker amplifier I2S BCLK |
| GPIO 15 | I2C SDA (touch, I2C port) |
| GPIO 16 | I2C SCL (touch, I2C port) |
| GPIO 17 | UART1 TX (UART1 port) |
| GPIO 18 | UART1 RX (UART1 port) |
| GPIO 19 | USB D- (native USB-C port) |
| GPIO 20 | USB D+ (native USB-C port) |
| GPIO 21 | Speaker amplifier mute control |
| GPIO 38 | Backlight |
| GPIO 39 | LCD MOSI |
| GPIO 40 | LCD CS |
| GPIO 41 | LCD DC |
| GPIO 42 | LCD SCK |
| GPIO 43 | UART0 TX (USB serial and UART0 terminal) |
| GPIO 44 | UART0 RX (USB serial and UART0 terminal) |
| GPIO 45 | Microphone / wireless module switch select |
| GPIO 46 | Wireless module BUSY |
| GPIO 47 | Touch interrupt |
| GPIO 48 | Touch reset |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 17 | GPIO, PWM, ADC | UART1 TX on the UART1 port (HY2.0-4P) |
| GPIO 18 | GPIO, PWM, ADC | UART1 RX on the UART1 port (HY2.0-4P) |
- UART1 port — GPIO 18, 17 (RX, TX) · HY2.0-4P
- I2C port — GPIO 16, 15 (SCL, SDA) · HY2.0-4P
Same bus as the touch controller (0x38)
- UART0 terminal — GPIO 44, 43 (RX, TX) · XH2.54-4P
Level-shifted, also a 5 V power input; shares UART0 with the USB serial port
- Wireless module header — GPIO 0, 1, 2, 3, 9, 10, 15, 16, 46 · 2 x 7-pin female
For Elecrow plug-in radio modules; GPIO 9/10 reach it only when GPIO 45 selects the module instead of the microphone
Good to know before you start
- It's documented here but not in the LCD Ultra Pro editor yet, so there's no ready-made export for it.
- GPIO 9 and 10 are shared: GPIO 45 switches them between the microphone and the radio-module header. You get one or the other.
- Hardware V1.1 cut the microphone from three lines to two (GPIO 9/10; V1.0 also used GPIO 3) and added the GPIO 21 mute line. Use the example folder that matches the version printed on your board.
- No PSRAM worries here, but 320×240 is small. Big fonts and few widgets per screen work best.
What it is good for
- •Small voice-controlled gadgets
- •Desk controllers with sound feedback
- •Experiments with Zigbee, Thread or nRF2401 via a plug-in module
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems 3.3.8 (the course also replaces some core files with Elecrow’s ESP32S3_120M package for 120 MHz PSRAM)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Is the CrowPanel Advance 2.4 really 800×480?
No. The README table says 800*480, but the panel is 320×240 and Elecrow's own example code configures it that way.
Which pins are free?
GPIO 17 and 18 on the UART1 port. The I2C port on GPIO 15/16 also works for sensors, but the touch controller sits on the same bus.
What is the difference to the Advance 2.8?
Only the panel size. Resolution, controller and the whole pin assignment are the same.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-Advance-2.4-HMI-ESP32-S3-AI-Powered-IPS-Touch-Screen-320x240
- https://www.elecrow.com/crowpanel-advance-2-4-hmi-esp32-320x240-ips-ai-display-artificial-intelligent-touchscreen-1.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_2.4-HMI_ESP32_AI_Display.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_2.4inch_Arduino_Course_V12.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel Advance 2.4" ESP32-S3 Arduino IDE settings
- CrowPanel Advance 2.4" ESP32-S3 pin planner
- CrowPanel Advance 2.4" ESP32-S3 side-by-side comparison
- CrowPanel Advance 2.4" ESP32-S3 LVGL memory estimate
- CrowPanel Advance 2.4" ESP32-S3 I2C address check
- Other ESP32 boards with the ST7789
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.