Elecrow · ESP32-S3 · 2.01" · 240×296
Elecrow CrowPanel 2.01" ESP32-S3 Watch Display specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel 2.01" ESP32-S3 Watch Display. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
It's sold as a bare PCB. No case, no strap. What you get is a 2.01-inch 240×296 IPS panel on a small board with everything a smartwatch prototype needs already on it.
The list is long for the size: ESP32-S3R8 with 8 MB PSRAM and 16 MB flash, an AXS5106L touch controller, a PCF8563 clock and an SC7A20H accelerometer on one I2C bus (GPIO 3/4), a PDM microphone, an I2S speaker amplifier, a vibration motor, a rotary encoder with push, a status LED and a battery charger.
Power is managed in detail. GPIO 40 switches the display, touch and backlight supply (active low), GPIO 47 the other peripherals, and GPIO 48 the audio section. That's useful for battery life, but it also means nothing lights up until your code enables the right rail. The panel is a GC9309 on SPI, and Elecrow's factory code drives it with Arduino_GFX.

- Screen
- 2.01" · 240×296
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.01-inch IPS, 240×296, GC9309 (SPI)
- AXS5106L capacitive touch
- ESP32-S3R8, 8 MB PSRAM, 16 MB flash
- Microphone and I2S speaker amplifier
- Encoder, vibration motor, accelerometer, RTC
- Switchable power rails for battery life
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 2.01" |
| Resolution | 240×296 px |
| Colour depth | 16-bit |
| Display controller | GC9309 (SPI) |
| Display interface | SPI |
| Touch | AXS5106L (capacitive, I2C) |
| Rotary encoder | Yes |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.0 schematic (Elecrow). PCB only, no case or strap. PCF8563 RTC and SC7A20H accelerometer (0x19) on the I2C bus; 1.0 mm battery connector with charger. |
| Display | 2.01-inch IPS, 240×296, GC9309 (SCK 7, MOSI 8, CS 9, DC 10, RST 6, TE 21), backlight GPIO 13 |
| Touch | AXS5106L on I2C GPIO 3/4, INT 2, RST 5 |
| Sensors | PCF8563 RTC, SC7A20H accelerometer (0x19) on the same I2C bus |
| Audio | PDM microphone (clock 12, data 11), amplifier I2S (data 41, BCLK 42, LRCLK 46), amp enable 48 |
| Power control | GPIO 40 display rail, GPIO 47 peripherals, GPIO 48 audio; battery ADC GPIO 1 |
| Inputs | Encoder A 20, B 19, push 18; BOOT button |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel 2.01-inch ESP32-S3 Watch Display, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Battery voltage (ADC) |
| GPIO 2 | Touch interrupt |
| GPIO 3 | I2C SCL (touch, RTC, accelerometer) |
| GPIO 4 | I2C SDA (touch, RTC, accelerometer) |
| GPIO 5 | Touch reset |
| GPIO 6 | LCD reset |
| GPIO 7 | LCD SCK |
| GPIO 8 | LCD MOSI |
| GPIO 9 | LCD CS |
| GPIO 10 | LCD DC |
| GPIO 11 | PDM microphone data |
| GPIO 12 | PDM microphone clock |
| GPIO 13 | Backlight |
| GPIO 14 | LCD power detect |
| GPIO 15 | Battery charge status |
| GPIO 16 | LED |
| GPIO 17 | USB power detect |
| GPIO 18 | Encoder push button |
| GPIO 19 | Encoder B |
| GPIO 20 | Encoder A |
| GPIO 21 | LCD tearing effect (TE) |
| GPIO 38 | External UART TX |
| GPIO 39 | External UART RX |
| GPIO 40 | Display, touch and backlight power enable (active low) |
| GPIO 41 | Speaker amplifier I2S data |
| GPIO 42 | Speaker amplifier I2S BCLK |
| GPIO 43 | UART0 TX (USB serial) |
| GPIO 44 | UART0 RX (USB serial) |
| GPIO 45 | Vibration motor enable |
| GPIO 46 | Speaker amplifier I2S LRCLK |
| GPIO 47 | Peripheral power enable |
| GPIO 48 | Audio power enable (active low) |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 38 | GPIO, PWM | External UART TX (solder pad) |
| GPIO 39 | GPIO, PWM | External UART RX (solder pad) |
- External UART pads — GPIO 38, 39 (TX, RX) · solder pads
Good to know before you start
- Not in the LCD Ultra Pro editor yet, so this is a reference page.
- Pull GPIO 40 low first, or the screen stays dark.
- It is a PCB without a case. Plan the enclosure and strap yourself.
- GPIO 38/39 are broken out as an extra UART on pads, and that is all the spare I/O there is.
What it is good for
- •Smartwatch and wearable prototypes
- •Voice-command remotes
- •Step counters and motion loggers
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems 3.3.3
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display controller does the CrowPanel 2.01 use?
A GC9309 over SPI. The factory code drives it with the Arduino_GFX library at 80 MHz.
Why is the display black after flashing my own code?
The display, touch and backlight supply is switched by GPIO 40, active low. Set it low before you initialise the panel.
Does it have an accelerometer?
Yes, an SC7A20H on the I2C bus with the touch controller and the PCF8563 clock.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel_2.01_inch-HMI_ESP32_Watch_Display_240_296
- https://www.elecrow.com/crowpanel-2-01inch-hmi-esp32-watch-display-240-296-ips-touch-screen-with-microphone-supports-voice-control-only-pcb.html
- https://www.elecrow.com/wiki/CrowPanel_2.01_inch-HMI_ESP32_Watch_Display_240_296_IPS_Touch_Screen_With_Microphone.html
- https://www.elecrow.com/wiki/2.01-Arduino-01-Environment_Setup.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel 2.01" ESP32-S3 Watch Display Arduino IDE settings
- CrowPanel 2.01" ESP32-S3 Watch Display pin planner
- CrowPanel 2.01" ESP32-S3 Watch Display side-by-side comparison
- CrowPanel 2.01" ESP32-S3 Watch Display LVGL memory estimate
- CrowPanel 2.01" ESP32-S3 Watch Display I2C address check
- Other ESP32 boards with the GC9309
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.