Elecrow · ESP32-S3 · 4.3" · 800×480
Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel Advance 4.3" ESP32-S3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
An RGB panel eats GPIOs, and the Advance 4.3 shows how Elecrow dealt with that. Sixteen data lines plus clock and sync use up most of the ESP32-S3, so the board adds an STC8H1K28 microcontroller on I2C (address 0x30) that handles backlight, buzzer, speaker enable and touch reset. You don't toggle a pin for the backlight here, you send a byte.
The other trick is a small two-position DIP switch. It routes GPIO 4, 5 and 6 to the microSD slot, the radio-module header or the I2S speaker path, and GPIO 19 and 20 to either the microphone or the UART1 port. Read the switch position before you debug an SD card that won't mount.
The rest is a solid 800×480 IPS panel with a GT911 touch controller at 0x5D, a BM8563 clock, battery charging and an ESP32-S3-WROOM-1-N16R8 with 8 MB PSRAM, which you'll need for full-screen frame buffers. Elecrow lists the display controller as ST7265.

- Screen
- 4.3" · 800×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 4.3-inch IPS, 800×480, 16-bit RGB
- GT911 capacitive touch (0x5D)
- STC8H I/O controller for backlight, buzzer and speaker
- DIP switch selects SD, radio module or audio
- BM8563 RTC, battery charging
- ESP32-S3, 16 MB flash, 8 MB PSRAM
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 4.3" |
| Resolution | 800×480 px |
| Colour depth | 16-bit |
| Display controller | ST7265 (RGB) |
| Display interface | RGB565 parallel |
| Touch | GT911 (capacitive, I2C 0x5D) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.3 schematic (Elecrow). From V1.1 on, backlight, buzzer, speaker enable and touch reset are handled by an STC8H1K28 I/O controller at I2C address 0x30; V1.0 switches the backlight through a PCA9557 I/O expander (its IO1) and drives the buzzer from GPIO 8. A 2-position DIP switch routes GPIO 4/5/6 and 19/20 to either the speaker and microphone, the wireless module and UART1 port, or the microSD slot and microphone (on V1.0 the SD position has no microphone). |
| Display | 4.3-inch IPS, 800×480, RGB565 (PCLK 39, HSYNC 40, VSYNC 41, DE 42) |
| Touch | GT911 at 0x5D on I2C GPIO 15/16, interrupt GPIO 1, reset via the I/O controller |
| Backlight | Set over I2C through the STC8H1K28 (0x30), values 0 to 245 in the current README |
| Function switch | GPIO 4/5/6: microSD, radio module or I2S audio; GPIO 19/20: microphone or UART1 port |
| Ports | UART0 (HY2.0-4P and XH2.54-4P), UART1 (HY2.0-4P), I2C (HY2.0-4P) |
| Size | 121.9 × 75.6 × 15.3 mm, active area 95.5 × 54 mm |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel Advance 4.3-inch ESP32-S3 HMI, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Touch interrupt |
| GPIO 2 | Wireless module header (V1.0: microphone WS) |
| GPIO 3 | LCD R6 |
| GPIO 4 | microSD MISO / wireless module MISO / I2S data to the speaker amplifier (DIP switch) |
| GPIO 5 | microSD SCK / wireless module SCK / I2S BCLK (DIP switch) |
| GPIO 6 | microSD MOSI / wireless module MOSI / I2S LRCLK (DIP switch) |
| GPIO 7 | LCD R3 |
| GPIO 8 | Wireless module header (V1.0: buzzer) |
| GPIO 9 | LCD G2 |
| GPIO 10 | LCD G3 |
| GPIO 11 | LCD G4 |
| GPIO 12 | LCD G5 |
| GPIO 13 | LCD G6 |
| GPIO 14 | LCD G7 |
| GPIO 15 | I2C SDA (touch, RTC, I/O controller, I2C port) |
| GPIO 16 | I2C SCL (touch, RTC, I/O controller, I2C port) |
| GPIO 17 | LCD R4 |
| GPIO 18 | LCD R5 |
| GPIO 19 | UART1 RX / microphone clock (DIP switch) |
| GPIO 20 | UART1 TX / microphone data (DIP switch) |
| GPIO 21 | LCD B3 |
| GPIO 38 | LCD B7 |
| GPIO 39 | LCD PCLK |
| GPIO 40 | LCD HSYNC |
| GPIO 41 | LCD VSYNC |
| GPIO 42 | LCD DE |
| GPIO 43 | UART0 TX (USB serial, UART0 port) |
| GPIO 44 | UART0 RX (USB serial, UART0 port) |
| GPIO 45 | LCD B6 |
| GPIO 46 | LCD R7 |
| GPIO 47 | LCD B4 |
| GPIO 48 | LCD B5 |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 19 | GPIO, PWM, ADC | UART1 RX on the UART1 port; the DIP switch decides whether it goes to the port or the microphone |
| GPIO 20 | GPIO, PWM, ADC | UART1 TX on the UART1 port; the DIP switch decides whether it goes to the port or the microphone |
- UART0 port — GPIO 44, 43 (RX, TX) · HY2.0-4P
Shared with the USB serial port
- UART0 terminal — GPIO 44, 43 (RX, TX) · XH2.54-4P
Level-shifted, also a 5 V power input
- UART1 port — GPIO 19, 20 (RX, TX) · HY2.0-4P
Connected only in the DIP-switch position that selects the wireless module
- I2C port — GPIO 16, 15 (SCL, SDA) · HY2.0-4P
Same bus as the GT911 touch (0x5D), the BM8563 RTC (0x51) and the STC8H I/O controller (0x30)
- Wireless module header — GPIO 2, 4, 5, 6, 8, 15, 16 · 2 x 7-pin female
GPIO 4/5/6 reach it only in the matching DIP-switch position
Good to know before you start
- Not in the LCD Ultra Pro editor yet. Use this page for wiring and planning.
- Backlight control changed between hardware versions. V1.0 switches it through a PCA9557 expander, V1.1 and later through the STC8H1K28. Match the example folder to the version printed on your board.
- You can't have microSD, the radio module and the speaker at once. The DIP switch picks one route.
- The I2C port shares the bus with touch (0x5D), the RTC (0x51) and the I/O controller (0x30).
What it is good for
- •Wall-mounted home panels
- •Kiosk-style menus with sound
- •Data loggers that need an RTC and an SD card
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems 3.3.8 (the course also replaces some core files with Elecrow’s ESP32S3_120M package for 120 MHz PSRAM)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
How do I turn on the backlight on the CrowPanel Advance 4.3?
On V1.1 and later, by writing a value to the STC8H1K28 at I2C address 0x30. Elecrow's wiki gives 0 to 245: 0 is the brightest, 244 the dimmest, 245 switches it off, and 246/247 turn the buzzer on and off. V1.0 boards use a PCA9557 expander instead, so use the example for your version.
Why does my SD card not work?
Check the DIP switch. GPIO 4/5/6 reach the microSD slot only in one switch position; in the others they go to the radio module or the audio path.
Which display controller is on the 4.3-inch Advance?
Elecrow lists ST7265. It is driven as a plain 16-bit RGB panel, so no SPI init sequence is needed.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-Advance-4.3-HMI-ESP32-S3-AI-Powered-IPS-Touch-Screen-800x480
- https://www.elecrow.com/crowpanel-advance-4-3-hmi-esp32-800x480-ai-display-ips-touch-artificial-intelligent-screen.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_4.3-HMI_ESP32_AI_Display.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_4.3inch_Arduino_Course_V13.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel Advance 4.3" ESP32-S3 Arduino IDE settings
- CrowPanel Advance 4.3" ESP32-S3 pin planner
- CrowPanel Advance 4.3" ESP32-S3 side-by-side comparison
- CrowPanel Advance 4.3" ESP32-S3 LVGL memory estimate
- CrowPanel Advance 4.3" ESP32-S3 I2C address check
- Other ESP32 boards with the ST7265
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.