Elecrow · ESP32-S3 · 2.8" · 320×240
Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel Advance 2.8" ESP32-S3 HMI. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Same board, bigger glass. The Advance 2.8 uses the identical schematic to the 2.4-inch model: 320×240 pixels, an ST7789 controller on SPI, and the same GPIO assignment down to the last pin. What you gain is a physically larger IPS panel, so buttons and text are easier to hit and read at the same resolution.
The electronics are generous for a screen this size. You get an ESP32-S3-WROOM-1-N16R8 with 16 MB flash and 8 MB PSRAM, capacitive touch, a digital microphone, an I2S speaker amplifier with a mute line, a buzzer, a microSD slot and a lithium battery connector with charging.
The "AI" in the product name points at the voice hardware, and "Meshtastic" at the radio-module header on the back, which takes small plug-in boards such as a LoRa module. The catch: the microphone and the module share two GPIOs through an analog switch. That trade-off decides more projects than the screen size does, so plan for it early.

- Screen
- 2.8" · 320×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.8-inch IPS, 320×240, ST7789 (SPI)
- Capacitive touch, I2C address 0x38
- ESP32-S3, 16 MB flash, 8 MB PSRAM
- Microphone, speaker amplifier, buzzer
- Battery connector with charging
- Plug-in header for Elecrow radio modules
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 2.8" |
| Resolution | 320×240 px |
| Colour depth | 16-bit |
| Display controller | ST7789 (SPI) |
| Display interface | SPI |
| Touch | FT6336U (capacitive, I2C 0x38) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.2 schematic (Elecrow). Same pin assignment as the Advance 2.4"; V1.1 changed the amplifier (GPIO 21 mute) and the microphone pins, V1.2 only the buttons. On V1.0 the microphone used three lines: data GPIO 10, WS GPIO 3, clock GPIO 9. |
| Display | 2.8-inch IPS, 320×240, ST7789 over SPI (GPIO 39/40/41/42), backlight GPIO 38 |
| Touch | Capacitive on I2C GPIO 15/16, INT 47, RST 48 |
| Audio | I2S amplifier (GPIO 11/12/13, mute 21), microphone (GPIO 9/10 via switch), buzzer GPIO 8 |
| USB | USB-C via CH340K (UART0) and a second USB-C on native USB (GPIO 19/20) |
| Ports | UART1 (HY2.0-4P), I2C (HY2.0-4P), UART0 terminal (XH2.54-4P), battery (PH2.0, 3.7 to 4.2 V) |
| Hardware revision | V1.2 (only the buttons changed from V1.1) |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel Advance 2.8-inch ESP32-S3 HMI, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button / wireless module CS |
| GPIO 1 | Wireless module header (TXD2) |
| GPIO 2 | Wireless module header (RXD2) |
| GPIO 3 | Wireless module SPI MOSI (V1.0: also microphone WS) |
| GPIO 4 | microSD MISO |
| GPIO 5 | microSD SCK |
| GPIO 6 | microSD MOSI |
| GPIO 7 | microSD CS |
| GPIO 8 | Buzzer |
| GPIO 9 | Microphone clock / wireless module MISO (selected by GPIO 45) |
| GPIO 10 | Microphone data / wireless module SPI CLK (selected by GPIO 45) |
| GPIO 11 | Speaker amplifier I2S LRCLK |
| GPIO 12 | Speaker amplifier I2S data |
| GPIO 13 | Speaker amplifier I2S BCLK |
| GPIO 15 | I2C SDA (touch, I2C port) |
| GPIO 16 | I2C SCL (touch, I2C port) |
| GPIO 17 | UART1 TX (UART1 port) |
| GPIO 18 | UART1 RX (UART1 port) |
| GPIO 19 | USB D- (native USB-C port) |
| GPIO 20 | USB D+ (native USB-C port) |
| GPIO 21 | Speaker amplifier mute control |
| GPIO 38 | Backlight |
| GPIO 39 | LCD MOSI |
| GPIO 40 | LCD CS |
| GPIO 41 | LCD DC |
| GPIO 42 | LCD SCK |
| GPIO 43 | UART0 TX (USB serial and UART0 terminal) |
| GPIO 44 | UART0 RX (USB serial and UART0 terminal) |
| GPIO 45 | Microphone / wireless module switch select |
| GPIO 46 | Wireless module BUSY |
| GPIO 47 | Touch interrupt |
| GPIO 48 | Touch reset |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 17 | GPIO, PWM, ADC | UART1 TX on the UART1 port (HY2.0-4P) |
| GPIO 18 | GPIO, PWM, ADC | UART1 RX on the UART1 port (HY2.0-4P) |
- UART1 port — GPIO 18, 17 (RX, TX) · HY2.0-4P
- I2C port — GPIO 16, 15 (SCL, SDA) · HY2.0-4P
Same bus as the touch controller (0x38)
- UART0 terminal — GPIO 44, 43 (RX, TX) · XH2.54-4P
Level-shifted, also a 5 V power input; shares UART0 with the USB serial port
- Wireless module header — GPIO 0, 1, 2, 3, 9, 10, 15, 16, 46 · 2 x 7-pin female
For Elecrow plug-in radio modules; GPIO 9/10 reach it only when GPIO 45 selects the module instead of the microphone
Good to know before you start
- This one isn't in the LCD Ultra Pro editor yet. The page is here for the specs and the pinout.
- A layout made for the 2.4-inch Advance runs unchanged, since both are 320×240 with the same pins.
- Microphone or radio module on GPIO 9/10, not both at once. GPIO 45 picks which. On V1.0 boards the microphone also used GPIO 3.
- Free I/O: just UART1 on GPIO 17/18.
What it is good for
- •Voice assistants and audio prompts on a small panel
- •Meshtastic-style messaging with a LoRa module
- •Battery-powered handheld controllers
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems 3.3.8 (the course also replaces some core files with Elecrow’s ESP32S3_120M package for 120 MHz PSRAM)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Does the CrowPanel Advance 2.8 have PSRAM?
Yes, 8 MB of octal PSRAM in the ESP32-S3-WROOM-1-N16R8 module, plus 16 MB of flash.
Can I use the microphone and a radio module together?
Not at the same time. An analog switch on GPIO 45 routes GPIO 9 and 10 either to the microphone or to the module header.
Why does the board have two USB-C ports?
One goes through a CH340K USB-serial chip to UART0. The other connects to the native USB pins of the ESP32-S3 on GPIO 19 and 20.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-Advance-2.8-HMI-ESP32-S3-AI-Powered-IPS-Touch-Screen-320x240
- https://www.elecrow.com/crowpanel-advance-2-8-hmi-esp32-ai-display-320x240-artificial-ips-intelligent-touchscreen.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_2.8-HMI_ESP32_AI_Display.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_2.8inch_Arduino_Course_V12.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel Advance 2.8" ESP32-S3 HMI Arduino IDE settings
- CrowPanel Advance 2.8" ESP32-S3 HMI pin planner
- CrowPanel Advance 2.8" ESP32-S3 HMI side-by-side comparison
- CrowPanel Advance 2.8" ESP32-S3 HMI LVGL memory estimate
- CrowPanel Advance 2.8" ESP32-S3 HMI I2C address check
- Other ESP32 boards with the ST7789
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.