Elecrow · ESP32-S3 · 3.5" · 480×320
Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel Advance 3.5" ESP32-S3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
480×320 over SPI is about where SPI starts to feel slow, and the Advance 3.5 sits right there. Elecrow pairs an ILI9488 controller with an ESP32-S3 running the bus at up to 80 MHz in its examples, which is fine for dashboards and menus. Full-screen animations will show the limit.
Compared with the 2.4 and 2.8-inch Advance boards, two things change. Touch moves to a GT911 with its reset on GPIO 48. Elecrow's wiki gives its I2C address as 0x5D; a GT911 can also come up at 0x14, depending on the INT level at reset, so scan the bus if nothing answers, and a BM8563 real-time clock joins the same I2C bus. Everything else carries over: ESP32-S3-WROOM-1-N16R8, microphone, I2S amplifier, buzzer, microSD, battery charging and the radio-module header.
One oddity in the factory code: the LovyanGFX config assigns GPIO 2 as the LCD reset, but on the V1.4 schematic GPIO 2 goes to the radio-module header and the panel reset comes from an on-board reset circuit. The panel's reset line isn't wired to any ESP32 pin at all. Leave the reset pin at -1 if you write your own driver and you'll avoid a conflict with the module.

- Screen
- 3.5" · 480×320
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 3.5-inch IPS, 480×320, ILI9488 over SPI
- GT911 capacitive touch (0x5D)
- BM8563 real-time clock
- ESP32-S3, 16 MB flash, 8 MB PSRAM
- Microphone, speaker amplifier, buzzer, microSD
- Elecrow radio-module header
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 3.5" |
| Resolution | 480×320 px |
| Colour depth | 16-bit |
| Display controller | ILI9488 (SPI) |
| Display interface | SPI |
| Touch | GT911 (capacitive, I2C 0x5D per the Elecrow wiki; a GT911 can also start at 0x14) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.4 schematic (Elecrow); the factory examples cover V1.2 to V1.4. BM8563 real-time clock on the I2C bus. The LCD reset line is not wired to an ESP32 GPIO, so it is not in the GPIO table. Revision history per the wiki: V1.2 improved the amplifier (GPIO 21 mute) and cut the microphone to two lines (GPIO 9/10); V1.0 also used GPIO 3 as microphone WS. V1.3 and V1.4 only changed the buttons. |
| Display | 3.5-inch IPS, 480×320, ILI9488 (SPI: SCK 42, MOSI 39, DC 41, CS 40), backlight GPIO 38 |
| Touch | GT911 at 0x5D (or 0x14), I2C GPIO 15/16, INT 47, RST 48 |
| Clock | BM8563 RTC on the same I2C bus (0x51) |
| Audio | Microphone, I2S amplifier with mute (GPIO 21), buzzer (GPIO 8) |
| Ports | UART1 and I2C (HY2.0-4P), UART0 terminal (XH2.54-4P), battery, speaker |
| Hardware revisions | V1.0, then V1.2 (new amplifier, GPIO 21 mute, two-wire mic); V1.3/V1.4 changed only the buttons |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel Advance 3.5-inch ESP32-S3 HMI, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button / wireless module CS |
| GPIO 1 | Wireless module header (TXD2) |
| GPIO 2 | Wireless module header (RXD2) |
| GPIO 3 | Wireless module SPI MOSI (V1.0: also microphone WS) |
| GPIO 4 | microSD MISO |
| GPIO 5 | microSD SCK |
| GPIO 6 | microSD MOSI |
| GPIO 7 | microSD CS |
| GPIO 8 | Buzzer |
| GPIO 9 | Microphone clock / wireless module MISO (selected by GPIO 45) |
| GPIO 10 | Microphone data / wireless module SPI CLK (selected by GPIO 45) |
| GPIO 11 | Speaker amplifier I2S LRCLK |
| GPIO 12 | Speaker amplifier I2S data |
| GPIO 13 | Speaker amplifier I2S BCLK |
| GPIO 15 | I2C SDA (touch, RTC, I2C port) |
| GPIO 16 | I2C SCL (touch, RTC, I2C port) |
| GPIO 17 | UART1 TX (UART1 port) |
| GPIO 18 | UART1 RX (UART1 port) |
| GPIO 19 | USB D- (native USB-C port) |
| GPIO 20 | USB D+ (native USB-C port) |
| GPIO 21 | Speaker amplifier mute control |
| GPIO 38 | Backlight |
| GPIO 39 | LCD MOSI |
| GPIO 40 | LCD CS |
| GPIO 41 | LCD DC |
| GPIO 42 | LCD SCK |
| GPIO 43 | UART0 TX (USB serial and UART0 terminal) |
| GPIO 44 | UART0 RX (USB serial and UART0 terminal) |
| GPIO 45 | Microphone / wireless module switch select |
| GPIO 46 | Wireless module BUSY |
| GPIO 47 | Touch interrupt |
| GPIO 48 | Touch reset |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 17 | GPIO, PWM, ADC | UART1 TX on the UART1 port (HY2.0-4P) |
| GPIO 18 | GPIO, PWM, ADC | UART1 RX on the UART1 port (HY2.0-4P) |
- UART1 port — GPIO 18, 17 (RX, TX) · HY2.0-4P
- I2C port — GPIO 16, 15 (SCL, SDA) · HY2.0-4P
Same bus as the GT911 touch (0x5D, or 0x14 depending on its reset state) and the BM8563 RTC (0x51)
- UART0 terminal — GPIO 44, 43 (RX, TX) · XH2.54-4P
Level-shifted, also a 5 V power input; shares UART0 with the USB serial port
- Wireless module header — GPIO 0, 1, 2, 3, 9, 10, 15, 16, 46 · 2 x 7-pin female
For Elecrow plug-in radio modules; GPIO 9/10 reach it only when GPIO 45 selects the module instead of the microphone
Good to know before you start
- Not in the LCD Ultra Pro editor yet, so this page is reference only.
- The I2C port shares the bus with the GT911 (0x5D or 0x14) and the RTC (0x51). Pick sensors with other addresses.
- SPI at 480×320 is fine for UI, slow for video. Don't expect smooth full-screen scrolling.
- Microphone or radio module on GPIO 9/10, selected by GPIO 45.
What it is good for
- •Clocks and schedulers that need real time without Wi-Fi
- •Home Assistant panels with voice prompts
- •Meshtastic handhelds with a LoRa module
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems 3.3.8 (the course also replaces some core files with Elecrow’s ESP32S3_120M package for 120 MHz PSRAM)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which touch controller does the CrowPanel Advance 3.5 use?
A GT911 on GPIO 15 (SDA) and 16 (SCL), with interrupt on GPIO 47 and reset on GPIO 48. Elecrow's wiki lists address 0x5D; depending on the reset sequence it can also answer at 0x14.
Does it keep time without power?
It has a BM8563 RTC on the I2C bus. Whether it keeps time with the board unplugged depends on the backup supply of your revision, so check the board.
Which GPIOs are free?
GPIO 17 and 18 on the UART1 port. The I2C port is usable for sensors, but it shares the bus with touch and the RTC.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-Advance-3.5-HMI-ESP32-S3-AI-Powered-IPS-Touch-Screen-480x320
- https://www.elecrow.com/crowpanel-advance-3-5-hmi-esp32-ai-display-480x320-artificial-intelligent-ips-touch-screen.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_3.5-HMI_ESP32_AI_Display.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_3.5inch_Arduino_Course_V13.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel Advance 3.5" ESP32-S3 Arduino IDE settings
- CrowPanel Advance 3.5" ESP32-S3 pin planner
- CrowPanel Advance 3.5" ESP32-S3 side-by-side comparison
- CrowPanel Advance 3.5" ESP32-S3 LVGL memory estimate
- CrowPanel Advance 3.5" ESP32-S3 I2C address check
- Other ESP32 boards with the ILI9488
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.