Elecrow · ESP32-S3 · 7.0" · 800×480
Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI specifications
This page collects the pinout, free GPIOs and hardware details of the CrowPanel Advance 7.0" ESP32-S3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Elecrow sells two 7-inch "CrowPanel Advance" boards and they're very different. This one is the ESP32-S3 model at 800×480. The other is an ESP32-P4 board at 1024×600 with Wi-Fi 6. Check the chip before ordering.
The S3 version uses an SC7277 RGB controller and a GT911 touch panel at 0x5D. It's the largest screen in the Advance S3 family, but the pixel count is the same as on the 4.3 and 5-inch boards, so text looks coarser up close. From a meter away it's fine, and that's where a 7-inch wall panel usually hangs.
Inside it follows the family pattern: ESP32-S3-WROOM-1-N16R8, an STC8H1K28 at I2C 0x30 for backlight, buzzer and speaker enable, a BM8563 clock, battery charging, a microphone and a DIP switch that shares GPIO 4/5/6 and 19/20 between SD, audio and the radio module. Elecrow keeps separate tutorials for V1.0, V1.2 and V1.3 to V1.5 (V1.4 changed the buttons, V1.5 only the silkscreen), and the pin table here comes from the V1.5 schematic.

- Screen
- 7.0" · 800×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 7-inch IPS, 800×480, SC7277 RGB
- GT911 capacitive touch
- ESP32-S3 with 16 MB flash and 8 MB PSRAM
- RTC, microphone, speaker amplifier, buzzer
- STC8H I/O controller for backlight
- Radio-module header (ESP32-H2, nRF2401 and others)
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 7.0" |
| Resolution | 800×480 px |
| Colour depth | 16-bit |
| Display controller | SC7277 (RGB) |
| Display interface | RGB565 parallel |
| Touch | GT911 (capacitive, I2C 0x5D) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V1.5 schematic (Elecrow). From V1.2 on, backlight, buzzer, speaker enable and touch reset are handled by an STC8H1K28 I/O controller at I2C address 0x30; V1.0 switches the backlight through a PCA9557 I/O expander (its IO1) and drives the buzzer from GPIO 8. A 2-position DIP switch routes GPIO 4/5/6 and 19/20 to either the speaker and microphone, the wireless module and UART1 port, or the microSD slot and microphone (on V1.0 the SD position has no microphone). Elecrow's wiki says only V1.0 supports Meshtastic. |
| Display | 7-inch IPS, 800×480, SC7277, 16-bit RGB |
| Touch | GT911 (0x5D) on I2C GPIO 15/16, interrupt GPIO 1 |
| Backlight | Via STC8H1K28 at 0x30; values changed between V1.2 and V1.3 |
| Audio | Microphone and I2S speaker path, selected with the DIP switch |
| Ports | UART0 (HY2.0-4P, XH2.54-4P), UART1 and I2C (HY2.0-4P), speaker, battery |
| Size | 181.26 × 108.36 × 16 mm, active area 156 × 87 mm |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow CrowPanel Advance 7.0-inch ESP32-S3 HMI, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Touch interrupt |
| GPIO 2 | Wireless module header (V1.0: microphone WS) |
| GPIO 3 | LCD R6 |
| GPIO 4 | microSD MISO / wireless module MISO / I2S data to the speaker amplifier (DIP switch) |
| GPIO 5 | microSD SCK / wireless module SCK / I2S BCLK (DIP switch) |
| GPIO 6 | microSD MOSI / wireless module MOSI / I2S LRCLK (DIP switch) |
| GPIO 7 | LCD R3 |
| GPIO 8 | Wireless module header (V1.0: buzzer) |
| GPIO 9 | LCD G2 |
| GPIO 10 | LCD G3 |
| GPIO 11 | LCD G4 |
| GPIO 12 | LCD G5 |
| GPIO 13 | LCD G6 |
| GPIO 14 | LCD G7 |
| GPIO 15 | I2C SDA (touch, RTC, I/O controller, I2C port) |
| GPIO 16 | I2C SCL (touch, RTC, I/O controller, I2C port) |
| GPIO 17 | LCD R4 |
| GPIO 18 | LCD R5 |
| GPIO 19 | UART1 RX / microphone clock (DIP switch) |
| GPIO 20 | UART1 TX / microphone data (DIP switch) |
| GPIO 21 | LCD B3 |
| GPIO 38 | LCD B7 |
| GPIO 39 | LCD PCLK |
| GPIO 40 | LCD HSYNC |
| GPIO 41 | LCD VSYNC |
| GPIO 42 | LCD DE |
| GPIO 43 | UART0 TX (USB serial, UART0 port) |
| GPIO 44 | UART0 RX (USB serial, UART0 port) |
| GPIO 45 | LCD B6 |
| GPIO 46 | LCD R7 |
| GPIO 47 | LCD B4 |
| GPIO 48 | LCD B5 |
Source: github.com, www.elecrow.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 19 | GPIO, PWM, ADC | UART1 RX on the UART1 port; the DIP switch decides whether it goes to the port or the microphone |
| GPIO 20 | GPIO, PWM, ADC | UART1 TX on the UART1 port; the DIP switch decides whether it goes to the port or the microphone |
- UART0 port — GPIO 44, 43 (RX, TX) · HY2.0-4P
Shared with the USB serial port
- UART0 terminal — GPIO 44, 43 (RX, TX) · XH2.54-4P
Level-shifted, also a 5 V power input
- UART1 port — GPIO 19, 20 (RX, TX) · HY2.0-4P
Connected only in the DIP-switch position that selects the wireless module
- I2C port — GPIO 16, 15 (SCL, SDA) · HY2.0-4P
Same bus as the GT911 touch (0x5D), the BM8563 RTC (0x51) and the STC8H I/O controller (0x30)
- Wireless module header — GPIO 2, 4, 5, 6, 8, 15, 16 · 2 x 7-pin female
GPIO 4/5/6 reach it only in the matching DIP-switch position
Good to know before you start
- It's a wiki-only entry for now: the LCD Ultra Pro editor doesn't support it yet.
- Not the same board as the CrowPanel Advanced 7" ESP32-P4. Different chip, resolution and pins.
- Brightness on V1.3 and later: 0 is full, 244 dim, 245 off. V1.2 uses 0x05 (off) to 0x10 (full), and V1.0 switches the backlight through a PCA9557 expander instead.
- Free GPIOs are rare. Plan on I2C sensors.
- Elecrow's wiki says only V1.0 boards support Meshtastic.
What it is good for
- •Wall-mounted Home Assistant panels
- •Machine or room status displays read from a distance
- •Panels that combine touch with voice prompts
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems 3.3.8 (the course also replaces some core files with Elecrow’s ESP32S3_120M package for 120 MHz PSRAM)
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What is the resolution of the CrowPanel Advance 7.0 ESP32-S3?
800×480. The 1024×600 7-inch board in the Advance range is the ESP32-P4 model.
Which display controller does it use?
Elecrow names the SC7277. It runs as a 16-bit RGB panel from the ESP32-S3.
How do I control the buzzer?
Through the STC8H1K28 I/O controller at I2C address 0x30. The command values depend on the hardware version, so use the example for yours.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/Elecrow-RD/CrowPanel-Advance-7-HMI-ESP32-S3-AI-Powered-IPS-Touch-Screen-800x480
- https://www.elecrow.com/wiki/ESP32_Display-7.0_inch(Advance_Series)wiki.html
- https://www.elecrow.com/crowpanel-advance-7-hmi-esp32-ai-display-800x480-ai-ips-touch-screen.html
- https://www.elecrow.com/wiki/ESP32_Display-7.0_inch%28Advance_Series%29wiki.html
- https://www.elecrow.com/wiki/CrowPanel_Advance_7.0inch_Arduino_Course_V15.html
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow ESP Terminal 3.5" SPI with Camera
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- CrowPanel Advance 7.0" ESP32-S3 Arduino IDE settings
- CrowPanel Advance 7.0" ESP32-S3 pin planner
- CrowPanel Advance 7.0" ESP32-S3 side-by-side comparison
- CrowPanel Advance 7.0" ESP32-S3 LVGL memory estimate
- CrowPanel Advance 7.0" ESP32-S3 I2C address check
- Other ESP32 boards with the SC7277
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.