Elecrow · ESP32-S3 · 3.5" · 320×480
Elecrow ESP Terminal 3.5" SPI with Camera specifications
This page collects the pinout, free GPIOs and hardware details of the Elecrow ESP Terminal 3.5" SPI. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
A camera, a microphone and a touch screen on one ESP32-S3. The ESP Terminal 3.5 SPI is built around that combination, which is why the display gets the simplest possible wiring: SPI on GPIO 12/13 with CS on 3 and DC on 42, shared with the microSD slot.
The OV2640 takes the parallel camera pins (D2 to D9, PCLK, VSYNC, HSYNC, XCLK), and an INMP441 I2S microphone sits on GPIO 38, 39 and 41. Touch is an FT6236 at 0x38 on GPIO 1/2, the same lines that carry the camera's control bus. A level-shifted copy of that bus goes to the I2C port.
For your own hardware there are two analog ports (GPIO 19, 20), two level-shifted digital ports (GPIO 11, 40) and a UART port. One honest warning: Elecrow's wiki and README say 16 MB flash and 8 MB PSRAM (a WROOM-1-N16R8), but the V2.0 schematic lists an ESP32-S3-WROOM-2-N32R8V module. Look at the module before you set the flash size in your IDE.

- Screen
- 3.5" · 320×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 3.5-inch TFT, 320×480, ILI9488 over SPI
- FT6236 capacitive touch
- OV2640 2 MP camera
- INMP441 I2S microphone and buzzer
- Two analog and two digital Crowtail ports
- microSD slot, PH2.0 battery input
Specifications
| Manufacturer | Elecrow |
|---|---|
| Screen size | 3.5" |
| Resolution | 320×480 px |
| Colour depth | 16-bit |
| Display controller | ILI9488 (SPI) |
| Display interface | SPI |
| Touch | FT6236 (capacitive, I2C 0x38) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 per the Elecrow wiki (see hardware note) |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Hardware V2.0. Elecrow's wiki and README list an ESP32-S3-WROOM-1-N16R8 (16 MB flash, 8 MB PSRAM), while the V2.0 schematic names an ESP32-S3-WROOM-2-N32R8V module; check the marking on your module. The I2C port is level-shifted from the touch / camera bus (GPIO 1 and 2). |
| Display | 3.5-inch, 320×480, ILI9488 (SPI: SCK 12, MOSI 13, CS 3, DC 42), backlight GPIO 46 |
| Touch | FT6236 at 0x38, SDA 2, SCL 1 |
| Camera | OV2640, XCLK 7, PCLK 17, VSYNC 4, HSYNC 5, data on 6/8/15/16/18/21/47/48 |
| Audio | INMP441 microphone (WS 38, SCK 39, SD 41), buzzer GPIO 45 |
| Ports | Analog GPIO 19 and 20, digital GPIO 11 and 40, UART, I2C (HY2.0-4P) |
| Power | 5 V, 500 mA over USB-C, or a Li-ion cell on PH2.0 with on-board charging |
| Size | 106 × 66 × 13 mm, active area 73.63 × 49.79 mm |
Board layout and connectors
Where each connector, button and LED sits on the Elecrow ESP Terminal 3.5-inch SPI with Camera, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | I2C SCL (touch, camera, I2C port) |
| GPIO 2 | I2C SDA (touch, camera, I2C port) |
| GPIO 3 | LCD CS |
| GPIO 4 | Camera VSYNC |
| GPIO 5 | Camera HSYNC |
| GPIO 6 | Camera D9 |
| GPIO 7 | Camera XCLK |
| GPIO 8 | Camera D2 |
| GPIO 9 | Battery voltage (ADC) |
| GPIO 10 | microSD CS |
| GPIO 11 | Digital port D (level-shifted) |
| GPIO 12 | SPI SCK (LCD, microSD) |
| GPIO 13 | SPI MOSI (LCD, microSD) |
| GPIO 14 | SPI MISO (microSD) |
| GPIO 15 | Camera D8 |
| GPIO 16 | Camera D7 |
| GPIO 17 | Camera PCLK |
| GPIO 18 | Camera D6 |
| GPIO 19 | Analog port A (A_IO19) |
| GPIO 20 | Analog port A (A_IO20) |
| GPIO 21 | Camera D5 |
| GPIO 38 | Microphone WS |
| GPIO 39 | Microphone SCK |
| GPIO 40 | Digital port D (level-shifted) |
| GPIO 41 | Microphone data |
| GPIO 42 | LCD DC |
| GPIO 43 | UART0 TX (UART port, USB serial) |
| GPIO 44 | UART0 RX (UART port, USB serial) |
| GPIO 45 | Buzzer |
| GPIO 46 | Backlight |
| GPIO 47 | Camera D3 |
| GPIO 48 | Camera D4 |
Source: github.com, www.elecrow.com, www.elecrow.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 11 | GPIO, PWM, ADC | On digital port 1 (HY2.0-4P, level-shifted) |
| GPIO 19 | GPIO, PWM, ADC | On analog port 1 (HY2.0-4P) |
| GPIO 20 | GPIO, PWM, ADC | On analog port 2 (HY2.0-4P) |
| GPIO 40 | GPIO, PWM | On digital port 2 (HY2.0-4P, level-shifted) |
- Analog port 1 — GPIO 19 · HY2.0-4P
- Analog port 2 — GPIO 20 · HY2.0-4P
- Digital port 1 — GPIO 11 · HY2.0-4P
Level-shifted, 5 V supply on the port
- Digital port 2 — GPIO 40 · HY2.0-4P
Level-shifted, 5 V supply on the port
- UART port — GPIO 44, 43 (RX, TX) · HY2.0-4P
Shares UART0 with the USB serial port
Good to know before you start
- This terminal is not in the LCD Ultra Pro editor yet.
- Check the module marking: the wiki and README say 16 MB flash, the V2.0 schematic 32 MB.
- SPI is shared between the screen and the SD card. Heavy SD reads will slow the display.
- The touch controller and the camera share GPIO 1/2. Initialise the camera with that bus in mind.
What it is good for
- •Camera viewfinders and snapshot devices
- •Voice and image AI experiments
- •Sensor terminals with analog inputs
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which touch controller does the ESP Terminal SPI use?
An FT6236 at I2C address 0x38, on GPIO 2 (SDA) and GPIO 1 (SCL).
Which pins are free?
GPIO 19 and 20 on the analog ports, GPIO 11 and 40 on the level-shifted digital ports.
How much flash does it have?
Elecrow's wiki and README say 16 MB with 8 MB PSRAM (ESP32-S3-WROOM-1-N16R8). The V2.0 schematic names a 32 MB WROOM-2 module, so check yours.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Elecrow CrowPanel family
- Elecrow CrowPanel 1.28" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel ESP32-C3 1.28" Round Display
- Elecrow CrowPanel 1.46" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel 2.01" ESP32-S3 Watch Display
- Elecrow CrowPanel 2.1" ESP32-S3 Round Rotary Display
- Elecrow CrowPanel Advance 2.4" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.4"
- Elecrow CrowPanel Advance 2.8" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 2.8"
- Elecrow CrowPanel Advance 3.5" ESP32-S3 HMI
- Elecrow CrowPanel ESP32 HMI 3.5"
- Elecrow ESP Terminal 3.5" 16-bit Parallel
- Elecrow CrowPanel Advance 4.3" ESP32-S3 HMI
- Elecrow CrowPanel ESP32-S3 HMI 4.3"
- Elecrow CrowPanel Advance 5.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 5" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 5.0"
- Elecrow CrowPanel Advance 7.0" ESP32-S3 HMI
- Elecrow CrowPanel Advanced 7" ESP32-P4 HMI
- Elecrow CrowPanel ESP32-S3 HMI 7.0"
- Elecrow CrowPanel Advanced 9" ESP32-P4 HMI
- Elecrow CrowPanel Advanced 10.1" ESP32-P4 HMI
Tools for this board
- Elecrow ESP Terminal 3.5" SPI Arduino IDE settings
- Elecrow ESP Terminal 3.5" SPI pin planner
- Elecrow ESP Terminal 3.5" SPI side-by-side comparison
- Elecrow ESP Terminal 3.5" SPI LVGL memory estimate
- Elecrow ESP Terminal 3.5" SPI I2C address check
- Other ESP32 boards with the ILI9488
- Find similar ESP32 display boards
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.