Waveshare · ESP32-S3 · 7.0" · 800×480
Waveshare ESP32-S3-Touch-LCD-7C specifications
This page collects the pinout and hardware details of the ESP32-S3-Touch-LCD-7C (also sold as the 7C-BOX). The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
7 to 36 volts in. That one spec line tells you where the 7C is meant to go: a wall, a machine or a vehicle, not a USB cable on a desk. Waveshare sells it as the 7C-BOX, with an enclosure, a fuel-gauged battery connection and a 3.5 mm audio jack.
The screen is an 800×480 IPS panel on a 16-bit RGB bus with GT911 five-point touch under tempered glass. The ESP32-S3 has more memory than most boards in this class, 32 MB of flash and 16 MB of PSRAM, which leaves room for double-buffered LVGL at full resolution.
Audio uses an ES8389 codec for output and an ES7210 for the microphones. An I/O expander takes over the slow signals (LCD and touch reset, backlight enable, speaker enable, microSD chip select, panel VCOM), so the RGB bus can have the GPIOs. A PCF85063 clock with a battery holder and a BQ27220 fuel gauge sit on the same I2C bus at GPIO 47/48.

- Screen
- 7.0" · 800×480
- Chip
- ESP32-S3
- Memory
- 32 MB flash, 16 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 7-inch IPS, 800×480, RGB
- GT911 touch, 5 points, tempered glass
- ESP32-S3: 32 MB flash, 16 MB PSRAM
- ES8389 codec, ES7210 microphones, 3.5 mm jack
- PCF85063 RTC, BQ27220 fuel gauge
- 7–36 V wide-range input
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 7.0" |
| Resolution | 800×480 px |
| Colour depth | 16-bit |
| Display controller | RGB565 parallel panel |
| Display interface | RGB565 parallel |
| Touch | GT911 (capacitive, I2C, 5 points) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 (32 MB flash, 16 MB PSRAM) |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 16 MB (OPI) |
| Flash | 32 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Sold as ESP32-S3-Touch-LCD-7C-BOX with an enclosure. An IO expander (EXIO0-5) handles LCD reset, touch reset, backlight, speaker enable, microSD CS and LCD VCOM. ES8389 codec, ES7210 microphone ADC, PCF85063 RTC with battery holder, BQ27220 fuel gauge, 7-36 V input, 3.5 mm audio jack. 195.34 x 110.76 mm. |
| Display | 800×480 IPS, RGB565: PCLK 7, DE 5, HSYNC 46, VSYNC 3 |
| Touch | GT911, interrupt GPIO 4, I2C SDA 47 / SCL 48 |
| Audio | MCLK 6, SCLK 44, LRCLK 16, DOUT 15, DIN 43 |
| microSD | MOSI 11, SCK 12, MISO 13, CS via expander |
| Power | 7–36 V input, PH2.0 battery, BQ27220 gauge |
| Size | 195.34 × 110.76 mm |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | LCD G3 |
| GPIO 1 | LCD R3 |
| GPIO 2 | LCD R4 |
| GPIO 3 | LCD VSYNC |
| GPIO 4 | Touch interrupt |
| GPIO 5 | LCD DE |
| GPIO 6 | I2S MCLK |
| GPIO 7 | LCD PCLK |
| GPIO 8 | LCD G6 |
| GPIO 9 | LCD G5 |
| GPIO 10 | LCD B7 |
| GPIO 11 | microSD MOSI |
| GPIO 12 | microSD SCK |
| GPIO 13 | microSD MISO |
| GPIO 14 | LCD B3 |
| GPIO 15 | I2S data out (speaker) |
| GPIO 16 | I2S LRCLK |
| GPIO 17 | LCD B6 |
| GPIO 18 | LCD B5 |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | LCD G7 |
| GPIO 38 | LCD B4 |
| GPIO 39 | LCD G2 |
| GPIO 40 | LCD R7 |
| GPIO 41 | LCD R6 |
| GPIO 42 | LCD R5 |
| GPIO 43 | I2S data in (microphones) |
| GPIO 44 | I2S SCLK |
| GPIO 45 | LCD G4 |
| GPIO 46 | LCD HSYNC |
| GPIO 47 | I2C SDA (touch, RTC, IO expander, fuel gauge) |
| GPIO 48 | I2C SCL (touch, RTC, IO expander, fuel gauge) |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
- I2C port — GPIO 47, 48 (SDA, SCL)
On-board I2C bus with touch, RTC and IO expander
Good to know before you start
- You can't select the 7C in the LCD Ultra Pro editor yet.
- Backlight and LCD reset are expander pins. Without the expander driver the screen stays dark.
- GPIO 43/44 carry I2S audio here, so UART0 is not on its usual pins.
What it is good for
- •Panels powered from 12 V or 24 V systems
- •Wall-mounted home controllers with audio
- •Vehicle or machine dashboards
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 32MB (256Mb) |
| Partition Scheme | 32M Flash (4.8MB APP/22MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What power supply does the ESP32-S3-Touch-LCD-7C need?
It accepts 7 to 36 V through its wide-range regulator, or USB for flashing.
How much PSRAM does it have?
16 MB, with 32 MB of flash.
Which pins does the I/O expander control?
LCD reset, touch reset, backlight enable, speaker enable, microSD chip select and the LCD VCOM supply.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.