Waveshare · ESP32-S3 · 1.54" · 240×240
Waveshare ESP32-S3-Touch-LCD-1.54 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-Touch-LCD-1.54. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Square 240×240 at 1.54 inches is a classic size, and Waveshare sells this board twice: as the ESP32-S3-LCD-1.54 without touch and as the Touch version with a CST816 controller. The layout is otherwise the same, so this page covers both.
It's an audio board as much as a display board. An ES8311 codec and an NS4150B amplifier drive a small speaker, an ES7210 records from two microphones, and the I2S lines sit on GPIO 8 to 12 with the amplifier enable on GPIO 7. The microSD slot is wired for 4-bit SDMMC (GPIO 13 to 18), which is faster than the 1-bit setups on most small boards.
The ST7789 takes SPI on GPIO 38/39 with CS 21, DC 45, reset 40 and backlight 46. A QMI8658 IMU and the touch controller share I2C on GPIO 41/42. There's also a PLUS button and battery charging, though Waveshare's text doesn't list the button's GPIO.

- Screen
- 1.54" · 240×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.54-inch, 240×240, ST7789 (SPI)
- CST816 touch (Touch version)
- ES8311 codec, ES7210 dual-mic ADC, NS4150B amplifier
- 4-bit SDMMC microSD
- QMI8658 six-axis IMU
- ESP32-S3R8, 16 MB flash, 8 MB PSRAM
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.54" |
| Resolution | 240×240 px |
| Colour depth | 16-bit |
| Display controller | ST7789 (SPI) |
| Display interface | SPI |
| Touch | CST816 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Touch version of the ESP32-S3-LCD-1.54 (the non-touch version has the same layout without the CST816). ES8311 codec, ES7210 dual-microphone ADC, NS4150B amplifier, QMI8658 IMU, battery charger. PLUS and PWR buttons; their GPIOs are not listed by Waveshare in text. |
| Display | 240×240, ST7789: SCK 38, MOSI 39, CS 21, DC 45, RST 40, backlight 46 |
| Touch | CST816, INT 48, RST 47 |
| Audio | MCLK 8, BCLK 9, LRCLK 10, DIN 11, DOUT 12, amplifier enable 7 |
| microSD | CLK 16, CMD 15, D0 17, D1 18, D2 13, D3 14 |
| I2C | SDA 42, SCL 41 |
| Buttons | BOOT (GPIO 0), PLUS, PWR |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-Touch-LCD-1.54, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | MINUS key / BOOT |
| GPIO 1 | Battery voltage (ADC) |
| GPIO 2 | Battery measurement enable |
| GPIO 3 | Charger status |
| GPIO 4 | PLUS key |
| GPIO 5 | PWR key |
| GPIO 6 | IMU interrupt |
| GPIO 7 | Speaker amplifier enable |
| GPIO 8 | I2S MCLK |
| GPIO 9 | I2S BCLK |
| GPIO 10 | I2S LRCLK |
| GPIO 11 | I2S data in (ES7210) |
| GPIO 12 | I2S data out (ES8311) |
| GPIO 13 | microSD D2 |
| GPIO 14 | microSD D3 |
| GPIO 15 | microSD CMD |
| GPIO 16 | microSD CLK |
| GPIO 17 | microSD D0 |
| GPIO 18 | microSD D1 |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | LCD CS |
| GPIO 38 | LCD SCK |
| GPIO 39 | LCD MOSI |
| GPIO 40 | LCD reset |
| GPIO 41 | I2C SCL (touch, IMU, codecs, expansion pad) |
| GPIO 42 | I2C SDA (touch, IMU, codecs, expansion pad) |
| GPIO 43 | UART0 TX (expansion pad) |
| GPIO 44 | UART0 RX (expansion pad) |
| GPIO 45 | LCD DC |
| GPIO 46 | Backlight |
| GPIO 47 | Touch reset |
| GPIO 48 | Touch interrupt |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the expansion pads |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the expansion pads |
- Expansion pads — GPIO 42, 41, 43, 44, 19, 20 (SDA, SCL, TX, RX, USB D-, USB D+) · solder pads
I2C is the on-board bus (touch, IMU, codecs)
Good to know before you start
- It's documented here, not in the LCD Ultra Pro editor (yet).
- The non-touch ESP32-S3-LCD-1.54 has the same pins, just no touch controller.
- Free GPIOs are scarce. Waveshare lists I2C, UART and USB pads for expansion.
What it is good for
- •Tiny voice assistants
- •Desk clocks with audio alerts
- •Square gauges and status displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Does the ESP32-S3-Touch-LCD-1.54 have a speaker?
It has an ES8311 codec and an NS4150B amplifier for a speaker, plus two microphones on an ES7210 ADC.
Which touch controller does it use?
A CST816 on I2C (GPIO 41/42), with interrupt on GPIO 48 and reset on GPIO 47.
What is the difference to the ESP32-S3-LCD-1.54?
Only the touch panel. The non-touch board omits the CST816; display, audio and SD wiring are the same.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.