Waveshare · ESP32-S3 · 1.9" · 170×320
Waveshare ESP32-S3-LCD-1.9 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-LCD-1.9. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
A narrow 170×320 IPS strip at 500 cd/m², which is bright for a board this size, on a Pico-style footprint with pin headers along both sides. If you've used a Raspberry Pi Pico, the shape will feel familiar.
The display is an ST7789V2 on SPI: clock 10, MOSI 13, CS 12, DC 11, reset 9 and backlight on GPIO 14. A QMI8658 IMU sits on I2C at GPIO 47/48. On the back there's a WS2812 RGB LED (on the non-touch version), a microSD slot and a 3.7 V battery connector with charging.
There's also a touch version, the ESP32-S3-Touch-LCD-1.9, with a CST816 controller on the same I2C bus and an IPEX antenna option. Memory on both is 16 MB of flash and 8 MB of PSRAM, plenty for a display this small.

- Screen
- 1.9" · 170×320
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- no touch
Key features
- 1.9-inch LCD, 170×320, ST7789V2, 500 cd/m²
- ESP32-S3R8, 16 MB flash, 8 MB PSRAM
- QMI8658 IMU
- WS2812 RGB LED, microSD
- Battery charging
- Pico-compatible headers
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.9" |
| Resolution | 170×320 px |
| Colour depth | 16-bit |
| Display controller | ST7789V2 (SPI) |
| Display interface | SPI |
| Touch | None (touch version: ESP32-S3-Touch-LCD-1.9, CST816) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Non-touch version with a WS2812 RGB LED on the back; the touch version (ESP32-S3-Touch-LCD-1.9) adds a CST816 controller and an IPEX antenna option. QMI8658 IMU, microSD slot, battery charging, Pico-compatible pin headers. 500 cd/m². |
| Display | 170×320, ST7789V2: SCK 10, MOSI 13, CS 12, DC 11, RST 9, backlight 14 |
| I2C | SDA 47, SCL 48 (IMU; touch on the touch version) |
| Buttons | BOOT (GPIO 0), RESET |
| Battery | MX1.25, 3.7 V lithium, charging |
| Variants | ESP32-S3-LCD-1.9 and ESP32-S3-Touch-LCD-1.9 (CST816) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Header GPIO |
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | Battery voltage (ADC) |
| GPIO 5 | Header GPIO |
| GPIO 6 | Header GPIO |
| GPIO 7 | IMU interrupt 2 |
| GPIO 8 | IMU interrupt 1 |
| GPIO 9 | LCD reset |
| GPIO 10 | LCD SCK |
| GPIO 11 | LCD DC |
| GPIO 12 | LCD CS |
| GPIO 13 | LCD MOSI |
| GPIO 14 | Backlight |
| GPIO 15 | Header GPIO |
| GPIO 16 | Header GPIO |
| GPIO 17 | Touch reset (touch version) |
| GPIO 18 | Header GPIO |
| GPIO 19 | Header GPIO / USB D- |
| GPIO 20 | Header GPIO / USB D+ |
| GPIO 21 | Touch interrupt (touch version) |
| GPIO 38 | Header GPIO |
| GPIO 39 | microSD MOSI |
| GPIO 40 | microSD MISO |
| GPIO 41 | microSD CLK |
| GPIO 42 | Header GPIO |
| GPIO 43 | UART0 TX |
| GPIO 44 | UART0 RX |
| GPIO 45 | Header GPIO |
| GPIO 46 | Header GPIO |
| GPIO 47 | I2C SDA (IMU, touch on the touch version) |
| GPIO 48 | I2C SCL (IMU, touch on the touch version) |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 1 | GPIO, PWM, ADC | On the header |
| GPIO 2 | GPIO, PWM, ADC | On the header |
| GPIO 3 | GPIO, PWM, ADC | On the header |
| GPIO 5 | GPIO, PWM, ADC | On the header |
| GPIO 6 | GPIO, PWM, ADC | On the header |
| GPIO 15 | GPIO, PWM, ADC | On the header; Waveshare's LED example also uses GPIO 15 |
| GPIO 16 | GPIO, PWM, ADC | On the header |
| GPIO 18 | GPIO, PWM, ADC | On the header |
| GPIO 19 | GPIO, PWM, ADC | On the header; also USB D- |
| GPIO 20 | GPIO, PWM, ADC | On the header; also USB D+ |
| GPIO 38 | GPIO, PWM | On the header |
| GPIO 42 | GPIO, PWM | On the header |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the header |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the header |
| GPIO 45 | GPIO, PWM | On the header; strapping pin |
| GPIO 46 | GPIO, PWM | On the header; strapping pin |
- Pico-style pin headers — GPIO 0, 1, 2, 3, 4, 5, 6, 7, 15, 16, 17, 18, 19, 20, 21, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48 · 2 x 20 pin header
GPIO 33-37 also reach the header but belong to the octal PSRAM; GPIO 47/48 are the on-board I2C bus
Good to know before you start
- The LCD Ultra Pro editor has no profile for this board yet.
- Waveshare publishes the header pinout only as an image.
- The RGB LED is only on the non-touch version.
What it is good for
- •Breadboard projects with a screen
- •Battery status displays
- •Tilt-controlled gadgets
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Is there a touch version of the ESP32-S3-LCD-1.9?
Yes, the ESP32-S3-Touch-LCD-1.9 with a CST816 controller.
What is the display resolution?
170×320 pixels on an ST7789V2.
Which pin controls the backlight?
GPIO 14.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.