Waveshare · ESP32-S3 · 0.85" · 128×128
Waveshare ESP32-S3-LCD-0.85 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-LCD-0.85. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
0.85 inches and 128×128 pixels. The screen is tiny, but this is really a small audio board with a display on top: an ES8311 codec, an NS4150 amplifier for a speaker, an ES7210 ADC with a microphone, and a 4-bit microSD slot for sound files.
The pin map will look familiar if you've seen the 1.54-inch Waveshare board. The GC9107 panel uses the same SPI pins (SCK 38, MOSI 39, CS 21, DC 45, reset 40, backlight 46), the I2S lines are on GPIO 8 to 12, the amplifier enable on GPIO 7 and the SD card on 13 to 18.
The chip is an ESP32-S3-PICO-1-N8R8, so there are 8 MB of flash and 8 MB of PSRAM in a single package. Waveshare's examples also drive addressable LEDs from GPIO 48. PLUS, PWR and BOOT buttons and a battery connector with charging round it off.

- Screen
- 0.85" · 128×128
- Chip
- ESP32-S3
- Memory
- 8 MB flash, 8 MB PSRAM (OPI)
- Input
- no touch
Key features
- 0.85-inch LCD, 128×128, GC9107
- ESP32-S3-PICO-1-N8R8: 8 MB flash, 8 MB PSRAM
- ES8311 codec, NS4150 amplifier, ES7210 microphone ADC
- 4-bit SDMMC microSD
- Battery charging
- PLUS, PWR and BOOT buttons
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 0.85" |
| Resolution | 128×128 px |
| Colour depth | 16-bit |
| Display controller | GC9107 (SPI) |
| Display interface | SPI |
| Touch | None |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-PICO-1-N8R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 8 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | ESP32-S3-PICO-1-N8R8 (8 MB flash, 8 MB PSRAM). ES8311 codec, NS4150 amplifier, ES7210 ADC with microphone, battery charging. PLUS, PWR and BOOT buttons; I2C, UART and USB pads. |
| Display | 128×128, GC9107 (SPI): SCK 38, MOSI 39, CS 21, DC 45, RST 40, backlight 46 |
| Audio | MCLK 8, BCLK 9, LRCLK 10, DIN 11, DOUT 12, amplifier 7 |
| microSD | CLK 16, CMD 15, D0 17, D1 18, D2 13, D3 14 |
| I2C | SDA 42, SCL 41 |
| LED | Addressable LED data on GPIO 48 |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-LCD-0.85, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | MINUS key / BOOT |
| GPIO 1 | Battery voltage (ADC) |
| GPIO 2 | Battery measurement enable |
| GPIO 3 | Charger status |
| GPIO 4 | PLUS key |
| GPIO 5 | PWR key |
| GPIO 6 | IMU interrupt 1 |
| GPIO 7 | Speaker amplifier enable |
| GPIO 8 | I2S MCLK |
| GPIO 9 | I2S BCLK |
| GPIO 10 | I2S LRCLK |
| GPIO 11 | I2S data in (ES7210) |
| GPIO 12 | I2S data out (ES8311) |
| GPIO 13 | microSD D2 |
| GPIO 14 | microSD D3 |
| GPIO 15 | microSD CMD |
| GPIO 16 | microSD CLK |
| GPIO 17 | microSD D0 |
| GPIO 18 | microSD D1 |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | LCD CS |
| GPIO 38 | LCD SCK |
| GPIO 39 | LCD MOSI |
| GPIO 40 | LCD reset |
| GPIO 41 | I2C SCL (IMU, codecs, expansion pad) |
| GPIO 42 | I2C SDA (IMU, codecs, expansion pad) |
| GPIO 43 | UART0 TX (expansion pad) |
| GPIO 44 | UART0 RX (expansion pad) |
| GPIO 45 | LCD DC |
| GPIO 46 | Backlight |
| GPIO 47 | IMU interrupt 2 |
| GPIO 48 | WS2812 LED data |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the expansion pads |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the expansion pads |
- Expansion pads — GPIO 42, 41, 43, 44, 19, 20 (SDA, SCL, TX, RX, USB D-, USB D+) · solder pads
I2C is the on-board bus (IMU, codecs)
Good to know before you start
- It's a wiki entry for now. The LCD Ultra Pro editor doesn't list it.
- 128×128 fits an icon and a few words. Design for that.
- Expansion is limited to I2C, UART and USB pads.
What it is good for
- •Tiny voice assistants
- •Sound boards and players
- •Desk notifiers
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 8MB (64Mb) |
| Partition Scheme | 8M with spiffs (3MB APP/1.5MB SPIFFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display driver does the ESP32-S3-LCD-0.85 use?
A GC9107 over 4-wire SPI, 128×128 pixels.
Does it have a speaker output?
Yes. An ES8311 codec feeds an NS4150 amplifier; the amplifier is enabled on GPIO 7.
How much memory is there?
8 MB of flash and 8 MB of PSRAM in the ESP32-S3-PICO-1-N8R8 package.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.