Waveshare · ESP32-S3 · 2.8" · 480×480
Waveshare ESP32-S3-Touch-LCD-2.8D specifications
This page collects the pinout and hardware details of the ESP32-S3-Touch-LCD-2.8D. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Information on this one is thin. Waveshare hasn't put up a product page we could find, and its documentation page wasn't reachable when we checked. What does exist is an official ESP-IDF board support package, waveshare/esp32_s3_touch_lcd_2_8d, and that's where everything on this page comes from.
According to the BSP, the 2.8D drives a 480×480 ST7701 panel over a 16-bit RGB bus (PCLK 42, DE 41, HSYNC 39, VSYNC 40) with the frame buffer in PSRAM. The ST7701's init sequence goes through a TCA9555 I/O expander. Touch is a GT911 on the I2C bus at GPIO 15/16, which it shares with a PCF85063 clock and the audio chips.
Audio is an ES8311 codec and an ES7210 ADC on I2S (GPIO 10 to 14). There's a 1-bit microSD interface on GPIO 1, 19 and 20, a WS2812 LED on GPIO 38 and a backlight on GPIO 46. Flash and PSRAM sizes aren't published, so I'd treat this board as one to buy only if you already have it in hand.

- Screen
- 2.8" · 480×480
- Chip
- ESP32-S3
- Memory
- Input
- capacitive touch
Key features
- 2.8-inch, 480×480, ST7701 RGB
- GT911 capacitive touch
- ES8311 codec and ES7210 ADC
- PCF85063 RTC, TCA9555 I/O expander
- WS2812 RGB LED
- Official ESP-IDF BSP
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 2.8" |
| Resolution | 480×480 px |
| Colour depth | 16-bit |
| Display controller | ST7701 (RGB + SPI init via IO expander) |
| Display interface | RGB565 parallel |
| Touch | GT911 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | Yes |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Documented by Waveshare only through its ESP-IDF board support package (hardware V1.0). TCA9555 IO expander, PCF85063 RTC, ES8311 codec and ES7210 ADC, WS2812 LED. The frame buffer lives in PSRAM; Waveshare does not publish the flash and PSRAM sizes for this model. |
| Display | 480×480, ST7701, RGB565: PCLK 42, DE 41, HSYNC 39, VSYNC 40, backlight 46 |
| Touch | GT911 on I2C SDA 15, SCL 16 |
| Audio | MCLK 12, SCLK 13, LRCLK 14, DOUT 11, DIN 10 |
| microSD | CLK 1, CMD 20, D0 19 |
| LED | WS2812 on GPIO 38 |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 1 | microSD CLK |
| GPIO 2 | LCD data 11 |
| GPIO 3 | LCD data 12 |
| GPIO 4 | LCD data 13 |
| GPIO 5 | LCD data 14 |
| GPIO 6 | LCD data 15 |
| GPIO 7 | LCD data 5 |
| GPIO 8 | LCD data 6 |
| GPIO 9 | LCD data 7 |
| GPIO 10 | I2S data in (ES7210) |
| GPIO 11 | I2S data out (ES8311) |
| GPIO 12 | I2S MCLK |
| GPIO 13 | I2S SCLK |
| GPIO 14 | I2S LRCLK |
| GPIO 15 | I2C SDA (touch, RTC, IO expander, codecs) |
| GPIO 16 | I2C SCL (touch, RTC, IO expander, codecs) |
| GPIO 17 | LCD data 8 |
| GPIO 18 | LCD data 9 |
| GPIO 19 | microSD D0 |
| GPIO 20 | microSD CMD |
| GPIO 21 | LCD data 10 |
| GPIO 38 | Addressable LED (WS2812) |
| GPIO 39 | LCD HSYNC |
| GPIO 40 | LCD VSYNC |
| GPIO 41 | LCD DE |
| GPIO 42 | LCD PCLK |
| GPIO 43 | LCD data 0 |
| GPIO 44 | LCD data 1 |
| GPIO 45 | LCD data 2 |
| GPIO 46 | Backlight |
| GPIO 47 | LCD data 3 |
| GPIO 48 | LCD data 4 |
Source: github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- Flash and PSRAM sizes are not published by Waveshare.
- GPIO 19/20 carry the SD card here, so native USB on those pins is not available.
What it is good for
- •Square smart-home panels with audio
- •ESP-IDF projects that start from a BSP
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
Where does the ESP32-S3-Touch-LCD-2.8D pin data come from?
From Waveshare's official ESP-IDF board support package for this board. No product page or text pinout was available.
Which display controller does it use?
An ST7701 with a 16-bit RGB bus, initialised through a TCA9555 I/O expander.
Is it the same as the 2.8C?
No, they are separate models. The 2.8C is a round 480×480 board sold with or without touch; the 2.8D has its own BSP and pin map.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.