LilyGO · ESP32-S3 · 3.95" · 480×480
LilyGO T-Panel Lite specifications
This page collects the pinout and hardware details of the LilyGO T-Panel Lite. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The Lite drops everything from the T-Panel that isn't the screen: no touch panel, no I/O expander, no ESP32-H2, no RS485 or CAN. What stays is the 3.95-inch 480×480 IPS display with an ST7701S, an ESP32-S3 with 16 MB flash and 8 MB PSRAM, a microSD slot and two keys.
Without the expander the wiring changes. The ST7701S init now runs over plain 9-bit SPI from the S3, with CS on GPIO 14 and clock and data shared with the microSD slot on GPIO 36 and 35. The RGB bus sits on GPIO 1 to 13 and 42, 45, 46, with PCLK 41, HSYNC 39, VSYNC 40 and DE 38. The backlight moves to GPIO 33.
Note the PSRAM type: LilyGO lists it as quad SPI, not octal. Pick the matching PSRAM mode in your IDE or the board won't boot properly. KEY1 is GPIO 48, KEY2 is GPIO 47.

- Screen
- 3.95" · 480×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (QSPI)
- Input
- no touch
Key features
- 3.95-inch IPS, 480×480, ST7701S
- No touch: two keys and BOOT
- ESP32-S3, 16 MB flash, 8 MB quad PSRAM
- microSD slot
- Direct SPI panel init (no expander)
Specifications
| Manufacturer | LilyGO |
|---|---|
| Screen size | 3.95" |
| Resolution | 480×480 px |
| Colour depth | 16-bit |
| Display controller | ST7701S (RGB + 9-bit SPI init) |
| Display interface | RGB565 parallel |
| Touch | None |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (QSPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | V1.0. Non-touch version of the T-Panel: no CST3240 touch, no XL9535 expander, no ESP32-H2, no RS485 / CAN. The ST7701S is initialised directly over SPI that it shares with the microSD slot. |
| Display | 480×480, ST7701S, RGB: PCLK 41, DE 38, HSYNC 39, VSYNC 40, backlight 33 |
| Panel init | 9-bit SPI: CS 14, SCK 36, MOSI 35 |
| microSD | CS 34, MOSI 35, SCK 36, MISO 37 |
| Buttons | KEY1 GPIO 48, KEY2 GPIO 47, BOOT GPIO 0 |
| I2C | SDA 17, SCL 18 |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | LCD B0 |
| GPIO 2 | LCD B1 |
| GPIO 3 | LCD B2 |
| GPIO 4 | LCD B3 |
| GPIO 5 | LCD B4 |
| GPIO 6 | LCD G0 |
| GPIO 7 | LCD G1 |
| GPIO 8 | LCD G2 |
| GPIO 9 | LCD G3 |
| GPIO 10 | LCD G4 |
| GPIO 11 | LCD G5 |
| GPIO 12 | LCD R0 |
| GPIO 13 | LCD R1 |
| GPIO 14 | LCD init SPI CS |
| GPIO 17 | I2C SDA |
| GPIO 18 | I2C SCL |
| GPIO 33 | Backlight |
| GPIO 34 | microSD CS |
| GPIO 35 | SPI MOSI (microSD, LCD init) |
| GPIO 36 | SPI SCK (microSD, LCD init) |
| GPIO 37 | microSD MISO |
| GPIO 38 | LCD DE |
| GPIO 39 | LCD HSYNC |
| GPIO 40 | LCD VSYNC |
| GPIO 41 | LCD PCLK |
| GPIO 42 | LCD R2 |
| GPIO 45 | LCD R4 |
| GPIO 46 | LCD R3 |
| GPIO 47 | KEY2 button |
| GPIO 48 | KEY1 button |
Source: github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Wiki entry only: the LCD Ultra Pro editor does not include the T-Panel Lite yet.
- Quad PSRAM. Select QSPI PSRAM, not OPI.
- Without touch, plan the UI around two keys or a network interface.
What it is good for
- •Wall status displays
- •Info boards and clocks
- •Dashboards controlled from a phone
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
Does the T-Panel Lite have touch?
No. The CST3240 touch panel of the T-Panel is not fitted on the Lite.
What PSRAM type does it use?
8 MB of quad SPI PSRAM, according to LilyGO.
How is the ST7701S initialised?
Directly over 9-bit SPI from the ESP32-S3 (CS GPIO 14), sharing SCK and MOSI with the microSD slot.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the LilyGO display board family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.