LilyGO · ESP32-S3 · 2.41" · 600×450
LilyGO T4-S3 AMOLED 2.41" specifications
This page collects the pinout, free GPIOs and hardware details of the LilyGO T4-S3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
600×450 at 2.41 inches gives the T4-S3 one of the highest pixel counts among small ESP32 AMOLED boards, and at 800 cd/m² it stays readable in a bright room. The panel driver is a Raydium RM690B0 on QSPI.
LilyGO keeps the T4-S3 in its shared LilyGo-AMOLED-Series library, and the board definition there is the cleanest pin source: data on GPIO 14, 10, 16 and 12, clock 15, CS 11, reset 13, tearing-effect line on 18 and a display power enable on GPIO 9. Touch and the SY6970 charger share I2C on GPIO 6/7. The microSD slot runs over SPI on GPIO 1 to 4.
The library comment calls the touch chip CS226SE, which reads like a typo for CST226SE. Whatever the exact name, it's handled by LilyGO's own library, so you don't need to pick a driver yourself if you start there. There is also a separate camera shield with its own schematic.

- Screen
- 2.41" · 600×450
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 2.41-inch AMOLED, 600×450, 800 cd/m²
- RM690B0 driver over QSPI with TE line
- Capacitive touch (CST226SE)
- ESP32-S3R8, 16 MB flash, 8 MB PSRAM
- SY6970 charger, microSD
Specifications
| Manufacturer | LilyGO |
|---|---|
| Screen size | 2.41" |
| Resolution | 600×450 px |
| Colour depth | 16-bit |
| Display controller | RM690B0 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | CST226SE (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Pins from the LilyGo-AMOLED-Series library (BOARD_AMOLED_241). SY6970 charger, 800 cd/m² panel. A camera shield schematic is published alongside. |
| Display | 600×450 AMOLED, RM690B0: D0 14, D1 10, D2 16, D3 12, CLK 15, CS 11, RST 13, TE 18 |
| Touch | INT 8, RST 17, I2C SDA 6 / SCL 7 |
| Power | SY6970 (IRQ on GPIO 5), display power enable GPIO 9 |
| microSD | CS 1, MOSI 2, SCK 3, MISO 4 |
| Buttons | BOOT (GPIO 0) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | microSD CS |
| GPIO 2 | microSD MOSI |
| GPIO 3 | microSD SCK |
| GPIO 4 | microSD MISO |
| GPIO 5 | Charger (PMU) interrupt |
| GPIO 6 | I2C SDA (touch, PMU) |
| GPIO 7 | I2C SCL (touch, PMU) |
| GPIO 8 | Touch interrupt |
| GPIO 9 | Display power enable |
| GPIO 10 | LCD data 1 |
| GPIO 11 | LCD CS |
| GPIO 12 | LCD data 3 |
| GPIO 13 | LCD reset |
| GPIO 14 | LCD data 0 |
| GPIO 15 | LCD QSPI clock |
| GPIO 16 | LCD data 2 |
| GPIO 17 | Touch reset |
| GPIO 18 | LCD tearing effect (TE) |
| GPIO 21 | Header GPIO |
| GPIO 38 | Header GPIO |
| GPIO 39 | Header GPIO |
| GPIO 40 | Header GPIO |
| GPIO 41 | Header GPIO |
| GPIO 42 | Header GPIO |
| GPIO 43 | UART0 TX (connector) |
| GPIO 44 | UART0 RX (connector) |
| GPIO 47 | Header GPIO |
| GPIO 48 | Header GPIO |
Source: github.com, wiki.lilygo.cc, github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 21 | GPIO, PWM | On the expansion header (P4) |
| GPIO 38 | GPIO, PWM | On the expansion header (P4) |
| GPIO 39 | GPIO, PWM | On the expansion header (P4) |
| GPIO 40 | GPIO, PWM | On the expansion header (P4) |
| GPIO 41 | GPIO, PWM | On the expansion header (P4) |
| GPIO 42 | GPIO, PWM | On the expansion header (P4) |
| GPIO 47 | GPIO, PWM | On the expansion header (P4) |
| GPIO 48 | GPIO, PWM | On the expansion header (P4) |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the UART connector (P2) |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the UART connector (P2) |
- Expansion header (P4) — GPIO 6, 7, 18, 21, 38, 39, 40, 41, 42, 47, 48 · pin header
I2C (GPIO 6 / 7, shared with touch and PMU), GPIO 18 is the display TE line; also VBUS and 3.3 V
- UART / I2C connector (P2) — GPIO 43, 44, 6, 7 (TX, RX, SDA, SCL) · connector
3.3 V supply
Good to know before you start
- The LCD Ultra Pro editor has no T4-S3 profile yet.
- The panel is not powered until GPIO 9 enables it.
- Full frames at 600×450 are large. Use PSRAM buffers and partial refresh.
What it is good for
- •High-resolution dashboards
- •Photo frames and image viewers
- •Camera preview with the shield
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enable |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3M APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
| Upload Mode | UART0/Hardware CDC |
| USB Mode | CDC and JTAG |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What resolution is the LilyGO T4-S3?
600×450 pixels on a 2.41-inch AMOLED with an RM690B0 driver.
Where are the T4-S3 pins defined?
In LilyGO's LilyGo-AMOLED-Series library, board configuration BOARD_AMOLED_241.
Does it have an SD card slot?
Yes, over SPI: CS GPIO 1, MOSI 2, SCK 3, MISO 4.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the LilyGO display board family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.