LilyGO · ESP32-S3 · 3.95" · 480×480
LilyGO T-Panel S3 specifications
This page collects the pinout and hardware details of the LilyGO T-Panel S3. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Two chips, one panel. The T-Panel pairs an ESP32-S3 for the 480×480 touch UI with an ESP32-H2-MINI-1 for Zigbee and Thread, and adds an RS485 or CAN module for wired buses. It's built as a smart-home wall panel that can talk to radios and field devices at the same time.
The 3.95-inch IPS screen uses an ST7701S with an RGB data bus. Its SPI init lines don't come from the S3 directly but from an XL9535 I/O expander at I2C 0x20, which also handles LCD reset, touch reset and the RS485 direction pin. Touch is a CST3240 with its interrupt on GPIO 21. The backlight is GPIO 14.
The H2 talks to the S3 over a UART on GPIO 47/48, with enable and boot lines on 34 and 33, so the S3 can reflash it. Versions matter here: V1.0 and V1.1 ship with RS485, V1.2 and V1.3 have a swappable RS485 or CAN module on GPIO 15/16.

- Screen
- 3.95" · 480×480
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM
- Input
- capacitive touch
Key features
- 3.95-inch IPS, 480×480, ST7701S RGB
- CST3240 capacitive touch
- ESP32-S3 (16 MB / 8 MB) plus ESP32-H2 for Zigbee / Thread
- RS485 or CAN module
- XL9535 I/O expander
- microSD over SPI
Specifications
| Manufacturer | LilyGO |
|---|---|
| Screen size | 3.95" |
| Resolution | 480×480 px |
| Colour depth | 16-bit |
| Display controller | ST7701S (RGB + SPI init via XL9535) |
| Display interface | RGB565 parallel |
| Touch | CST3240 (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 + ESP32-H2-MINI-1 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | ESP32-H2-MINI-1 co-processor (4 MB) for Zigbee / Thread. XL9535 IO expander (I2C 0x20) drives the ST7701S SPI init, LCD reset, touch reset and RS485 direction. V1.2 made the RS485 module swappable with CAN; V1.3 changed the structure. |
| Display | 480×480 IPS, ST7701S: PCLK 41, HSYNC 39, VSYNC 40, backlight 14 |
| Touch | CST3240, I2C SDA 17 / SCL 18, INT 21 |
| ESP32-H2 | UART TX 48 / RX 47, enable 34, boot 33 |
| RS485 / CAN | TX 16, RX 15 |
| microSD | CS 38, MOSI 35, SCK 36, MISO 37 |
| Versions | V1.0-V1.1 RS485; V1.2-V1.3 swappable RS485 / CAN; V1.3 new structure |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | LCD B0 |
| GPIO 2 | LCD B1 |
| GPIO 3 | LCD B2 |
| GPIO 4 | LCD B3 |
| GPIO 5 | LCD B4 |
| GPIO 6 | LCD G0 |
| GPIO 7 | LCD G1 |
| GPIO 8 | LCD G2 |
| GPIO 9 | LCD G3 |
| GPIO 10 | LCD G4 |
| GPIO 11 | LCD G5 |
| GPIO 12 | LCD R0 |
| GPIO 13 | LCD R1 |
| GPIO 14 | Backlight |
| GPIO 15 | RS485 / CAN RX |
| GPIO 16 | RS485 / CAN TX |
| GPIO 17 | I2C SDA (touch, XL9535) |
| GPIO 18 | I2C SCL (touch, XL9535) |
| GPIO 21 | Touch interrupt |
| GPIO 33 | ESP32-H2 BOOT |
| GPIO 34 | ESP32-H2 enable |
| GPIO 35 | microSD MOSI |
| GPIO 36 | microSD SCK |
| GPIO 37 | microSD MISO |
| GPIO 38 | microSD CS |
| GPIO 39 | LCD HSYNC |
| GPIO 40 | LCD VSYNC |
| GPIO 41 | LCD PCLK |
| GPIO 42 | LCD R2 |
| GPIO 45 | LCD R4 |
| GPIO 46 | LCD R3 |
| GPIO 47 | ESP32-H2 UART RX |
| GPIO 48 | ESP32-H2 UART TX |
Source: github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
- RS485 / CAN terminal — GPIO 15, 16 (RX, TX) · screw terminal
V1.0-V1.1: RS485; V1.2-V1.3: replaceable RS485 or CAN module
Good to know before you start
- The LCD Ultra Pro editor does not list the T-Panel yet.
- No LCD output without the XL9535 driver: the panel init runs through it.
- The ESP32-H2 needs its own firmware for Zigbee or Thread.
What it is good for
- •Zigbee or Thread hub with a screen
- •Modbus / RS485 controllers
- •CAN-connected machine panels
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
What is the ESP32-H2 on the T-Panel for?
It is a second chip for 802.15.4 radio (Zigbee, Thread), connected to the ESP32-S3 over UART.
Does the T-Panel have CAN?
From V1.2 the RS485 module is replaceable with a CAN module. V1.0 and V1.1 have RS485 only.
Which touch chip does it use?
A CST3240 on I2C (GPIO 17/18), interrupt on GPIO 21.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the LilyGO display board family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Something wrong on this page?
Tell me what you found. I check every report and fix the page.