LilyGO · ESP32-S3 · 1.2" · 390×390
LilyGO T-Encoder-Pro specifications
This page collects the pinout, free GPIOs and hardware details of the LilyGO T-Encoder-Pro. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Turn it, press it, touch it. The T-Encoder-Pro is LilyGO's take on the smart-knob idea: a round 1.2-inch AMOLED at 390×390 sitting inside a rotary encoder that also clicks when pushed. The encoder phases are on GPIO 1 and 2, the push switch on GPIO 0, and a buzzer on GPIO 17 gives you detent clicks or alerts.
There are two panel versions in circulation. One pairs an SH8601 driver with a CHSC5816 touch controller, the other a CO5300 with a CST816 at 0x15. LilyGO's pin_config.h has a switch for both, and the QSPI pins stay the same: CS 10, clock 12, data 11, 13, 7 and 14, reset 4, power enable 3.
Touch runs on I2C at GPIO 5/6 with reset 8 and interrupt 9. The chip is an ESP32-S3R8 with 16 MB flash and 8 MB PSRAM, and the product page lists two Qwiic connectors for adding sensors.

- Screen
- 1.2" · 390×390
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- Round 1.2-inch AMOLED, 390×390
- Rotary encoder with push switch
- Capacitive touch (CHSC5816 or CST816)
- Buzzer on GPIO 17
- ESP32-S3R8, 16 MB flash, 8 MB PSRAM
- Two Qwiic connectors
Specifications
| Manufacturer | LilyGO |
|---|---|
| Screen size | 1.2" |
| Resolution | 390×390 px |
| Colour depth | 16-bit |
| Display controller | SH8601 or CO5300 (QSPI AMOLED) |
| Display interface | QSPI |
| Touch | CHSC5816 or CST816 (capacitive, I2C) |
| Rotary encoder | Yes |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Two panel versions: SH8601 with CHSC5816 touch, or CO5300 with CST816 touch (I2C 0x15); the example config selects one. V1.0 (2024-02-02). |
| Display | 390×390 AMOLED, SH8601 or CO5300: CS 10, CLK 12, D0 11, D1 13, D2 7, D3 14, RST 4, enable 3 |
| Touch | CHSC5816 or CST816 (0x15), SDA 5, SCL 6, RST 8, INT 9 |
| Encoder | A on GPIO 1, B on GPIO 2, push on GPIO 0 |
| Buzzer | GPIO 17 |
| Hardware version | V1.0 (2024-02-02) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Knob push button |
| GPIO 1 | Encoder A |
| GPIO 2 | Encoder B |
| GPIO 3 | Display power enable |
| GPIO 4 | LCD reset |
| GPIO 5 | I2C SDA (touch) |
| GPIO 6 | I2C SCL (touch) |
| GPIO 7 | LCD data 2 |
| GPIO 8 | Touch reset |
| GPIO 9 | Touch interrupt |
| GPIO 10 | LCD CS |
| GPIO 11 | LCD data 0 |
| GPIO 12 | LCD QSPI clock |
| GPIO 13 | LCD data 1 |
| GPIO 14 | LCD data 3 |
| GPIO 17 | Buzzer |
| GPIO 43 | UART0 TX (connectors) |
| GPIO 44 | UART0 RX (connectors) |
Source: github.com, www.lilygo.cc, github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 43 | GPIO, UART_TX | UART0 TX on both 4-pin connectors |
| GPIO 44 | GPIO, UART_RX | UART0 RX on both 4-pin connectors |
- Connector CN1 — GPIO 43, 44 (TX, RX) · 4-pin (Qwiic-style)
Also an external I2C pair (E_SCL / E_SDA) and 5 V
- Connector CN2 — GPIO 43, 44 (TX, RX) · 4-pin (Qwiic-style)
UART0 and 5 V
Good to know before you start
- It's in the wiki only; the LCD Ultra Pro editor doesn't support it yet.
- Find out which panel you have (SH8601 or CO5300). The touch driver differs too.
- The push button is GPIO 0, the boot strap. Do not hold it during power-up unless you want download mode.
What it is good for
- •Volume and light dimmer knobs
- •Thermostat controllers
- •Menu dials for desk setups
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB Mode | Hardware CDC and JTAG |
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
How big is the T-Encoder-Pro display?
1.2 inches, round, 390×390 pixels.
Which pins does the encoder use?
Phase A on GPIO 1, phase B on GPIO 2 and the push switch on GPIO 0.
Why are there two touch drivers in the examples?
LilyGO shipped two panel versions: SH8601 with CHSC5816 touch and CO5300 with CST816 touch.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the LilyGO display board family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.