LilyGO · ESP32-C6 · 0.85" · 128×128
LilyGO T-QT-C6 specifications
This page collects the pinout and hardware details of the LilyGO T-QT-C6. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
About the size of a thumb, the T-QT-C6 puts a 0.85-inch 128×128 touch screen on an ESP32-C6. It's LilyGO's tiny form factor with Wi-Fi 6, Bluetooth 5 and Zigbee / Thread inside, and an optional battery backboard on the back.
Two LCD drivers have shipped, GC9107 and ST7735, and LilyGO's pin_config.h has a switch for both, with different column and row offsets. The pins don't change: CS 14, DC 19, SCK 18, MOSI 15, reset 20, backlight 2. A CST816T touch controller and an LSM6DSL IMU share I2C on GPIO 21/22, with touch interrupt on GPIO 7 and reset on 23.
Memory is tight: 4 MB of flash and no PSRAM. Battery measurement is switched on by GPIO 8 and read on GPIO 6. V1.2 changed the charger to an SGM41562, and the battery backboard has versions of its own that you select in the config.

- Screen
- 0.85" · 128×128
- Chip
- ESP32-C6
- Memory
- 4 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 0.85-inch, 128×128 LCD
- GC9107 or ST7735 driver
- CST816T touch
- ESP32-C6: Wi-Fi 6, Zigbee, Thread
- LSM6DSL IMU
- Battery backboard option
Specifications
| Manufacturer | LilyGO |
|---|---|
| Screen size | 0.85" |
| Resolution | 128×128 px |
| Colour depth | 16-bit |
| Display controller | GC9107 or ST7735 (SPI) |
| Display interface | SPI |
| Touch | CST816T (capacitive, I2C) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 4 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | V1.2 (2024) changed the charger to an SGM41562; battery backboards have their own versions (select in pin_config.h). The LCD driver is GC9107 or ST7735 depending on the batch. LSM6DSL IMU, 4 MB flash, no PSRAM. |
| Display | 128×128: CS 14, DC 19, SCK 18, MOSI 15, RST 20, backlight 2 |
| Touch | CST816T, INT 7, RST 23, I2C SDA 21 / SCL 22 |
| Battery | Measurement enable 8, ADC 6 |
| Memory | 4 MB flash, no PSRAM |
| Versions | V1.0 (2023), V1.1 battery backboard, V1.2 SGM41562 charger |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 2 | Backlight |
| GPIO 3 | IMU enable |
| GPIO 6 | Battery voltage (ADC) |
| GPIO 7 | Touch interrupt |
| GPIO 8 | Battery measurement enable |
| GPIO 9 | Status LED |
| GPIO 14 | LCD CS |
| GPIO 15 | LCD MOSI |
| GPIO 18 | LCD SCK |
| GPIO 19 | LCD DC |
| GPIO 20 | LCD reset |
| GPIO 21 | I2C SDA (touch, IMU) |
| GPIO 22 | I2C SCL (touch, IMU) |
| GPIO 23 | Touch reset |
Source: github.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- Pick the right LCD driver (GC9107 or ST7735) for your batch.
- 4 MB flash, no PSRAM: keep the UI minimal.
What it is good for
- •Zigbee buttons with a screen
- •Keychain-size gadgets
- •Tiny status indicators
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| CPU Frequency | 160MHz |
| Flash Mode | QIO |
| Flash Size | 4MB (32Mb) |
| Partition Scheme | Huge APP (3MB No OTA/1MB SPIFFS) |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display driver does the T-QT-C6 use?
Either a GC9107 or an ST7735 depending on the batch; LilyGO's config supports both.
Does it have PSRAM?
No. It has 4 MB of flash and the ESP32-C6's internal SRAM.
Which touch controller is used?
A CST816T on I2C (GPIO 21/22).
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the LilyGO display board family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.