Waveshare · ESP32-C6 · 0.85" · 128×128
Waveshare ESP32-C6-LCD-0.85 specifications
This page collects the pinout and hardware details of the ESP32-C6-LCD-0.85. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Eight RGB LEDs in a ring around a 0.85-inch screen. The ESP32-C6-LCD-0.85 is clearly meant as a little voice or notification gadget: the 128×128 ST7735 shows an icon or a word, and the LED ring does the rest.
The audio side is complete. An ES8311 codec with an NS4150 amplifier drives a speaker header, and an ES7210 ADC with two microphones handles voice input with echo cancellation. There's a microSD slot for sound files, a 3.7 V battery connector with charging, and PLUS, PWR and BOOT buttons.
The chip is an ESP32-C6FH8 with 8 MB of in-package flash, Wi-Fi 6 and Zigbee / Thread, which is a step back in memory from the S3 version of this board. Waveshare's GPIO table assigns every pin, a QMI8658 IMU included, so there's no spare GPIO beyond the UART pads.

- Screen
- 0.85" · 128×128
- Chip
- ESP32-C6
- Memory
- 8 MB flash, no PSRAM
- Input
- no touch
Key features
- 0.85-inch, 128×128, ST7735
- ESP32-C6FH8, 8 MB flash
- ES8311 + ES7210 audio, NS4150 amplifier
- Ring of 8 RGB LEDs
- microSD, battery charging
- PLUS, PWR, BOOT buttons
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 0.85" |
| Resolution | 128×128 px |
| Colour depth | 16-bit |
| Display controller | ST7735 (SPI) |
| Display interface | SPI |
| Touch | None |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6FH8 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 8 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | ESP32-C6FH8 (8 MB flash). ES8311 codec, NS4150 amplifier, ES7210 dual-mic ADC, ring of 8 RGB LEDs, battery charging, microSD, PLUS / PWR / BOOT buttons. GPIO table published only as an image. |
| Display | 128×128, ST7735 (4-wire SPI) |
| Audio | ES8311, NS4150, ES7210, two microphones, speaker header |
| LEDs | 8 programmable RGB LEDs in a ring |
| Memory | 8 MB flash, no PSRAM |
| Expansion | I2C and UART pads |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-C6-LCD-0.85, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Battery voltage (ADC) |
| GPIO 1 | SPI SCK (LCD, microSD) |
| GPIO 2 | SPI MOSI (LCD, microSD) |
| GPIO 3 | LCD DC |
| GPIO 4 | LCD reset |
| GPIO 5 | LCD CS |
| GPIO 6 | Backlight |
| GPIO 7 | I2C SCL (IMU, codecs, pads) |
| GPIO 8 | I2C SDA (IMU, codecs, pads) |
| GPIO 9 | BOOT button |
| GPIO 12 | USB D- |
| GPIO 13 | USB D+ |
| GPIO 14 | RGB LED ring data (WS2812) |
| GPIO 15 | Speaker amplifier enable |
| GPIO 16 | microSD MISO / UART TX |
| GPIO 17 | microSD CS / UART RX |
| GPIO 18 | PLUS key |
| GPIO 19 | I2S MCLK |
| GPIO 20 | I2S SCLK |
| GPIO 21 | I2S ASDOUT (ES7210) |
| GPIO 22 | I2S LRCLK |
| GPIO 23 | I2S DSDIN (ES8311) |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
- Expansion pads — GPIO 8, 7, 16, 17 (SDA, SCL, TX, RX) · solder pads
UART pads share GPIO 16/17 with the microSD slot; I2C is the on-board bus
Good to know before you start
- The LCD Ultra Pro editor doesn't support this board yet.
- Only 8 MB flash and no PSRAM.
- GPIO 16 / 17 serve both the microSD slot and the UART pads.
What it is good for
- •Voice assistants with a light ring
- •Zigbee door chimes and notifiers
- •Tiny desk gadgets
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 8MB (64Mb) |
| Partition Scheme | 8M with spiffs (3MB APP/1.5MB SPIFFS) |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which display driver does the ESP32-C6-LCD-0.85 use?
An ST7735 over 4-wire SPI.
How many LEDs are in the ring?
Eight programmable RGB LEDs.
How does it differ from the ESP32-S3-LCD-0.85?
It uses an ESP32-C6FH8 (Wi-Fi 6, Zigbee, no PSRAM) instead of an ESP32-S3 with PSRAM.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-C3 / C6 family
- Waveshare ESP32-C6 1.3" LCD
- Waveshare ESP32-C3 1.47" LCD
- Waveshare ESP32-C6 1.47" LCD
- Waveshare ESP32-C6 Touch LCD 1.47"
- Waveshare ESP32-C6-Touch-LCD-1.54
- Waveshare ESP32-C6 Touch LCD 1.69"
- Waveshare ESP32-C6-Touch-LCD-1.83
- Waveshare ESP32-C6-LCD-1.9
- Waveshare ESP32-C6-LCD-2.73
- Waveshare ESP32-C6-Touch-LCD-2.8
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.