Waveshare · ESP32-C6 · 1.54" · 240×240
Waveshare ESP32-C6-Touch-LCD-1.54 specifications
This page collects the pinout and hardware details of the ESP32-C6-Touch-LCD-1.54. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Waveshare documents this one properly. Every GPIO of the ESP32-C6-Touch-LCD-1.54 is listed in the official table, which is more than most small boards get, and it shows how tightly the C6's pins are packed.
The 240×240 ST7789 sits on SPI: clock 1, MOSI 2, DC 3, reset 4, CS 11 and backlight 6. Touch interrupt is GPIO 5, the IMU interrupt GPIO 10, and the I2C bus for touch, IMU and codecs is on GPIO 8 (SDA) and 7 (SCL). Audio takes GPIO 19 to 23 with the amplifier enable on 15. GPIO 0 reads the battery voltage, and the PLUS button is GPIO 18.
One shared pair to watch: GPIO 16 and 17 are the microSD MISO and CS, but also the UART pads. Use the card or the serial port, not both. There's an ETA6098 charger, an ES8311 codec with an NS4150B amplifier and an ES7210 for two microphones.

- Screen
- 1.54" · 240×240
- Chip
- ESP32-C6
- Memory
- 16 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 1.54-inch, 240×240, ST7789
- CST816 touch (touch version)
- ESP32-C6, 16 MB flash
- ES8311 + ES7210, NS4150B amplifier
- QMI8658 IMU
- Complete official GPIO table
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.54" |
| Resolution | 240×240 px |
| Colour depth | 16-bit |
| Display controller | ST7789 (SPI) |
| Display interface | SPI |
| Touch | CST816 (capacitive, I2C; touch version) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Touch version of the ESP32-C6-LCD-1.54. ETA6098 charger, TMI3112H 3.3 V DC-DC, QMI8658 IMU, ES8311 codec, ES7210 dual-mic ADC, NS4150B amplifier. GPIO 16/17 are shared between the microSD slot and the UART pads. |
| Display | 240×240: SCK 1, MOSI 2, DC 3, RST 4, CS 11, backlight 6 |
| Touch / IMU | Touch INT 5, IMU INT 10, I2C SDA 8 / SCL 7 |
| Audio | MCLK 19, SCLK 20, LRCLK 22, data 21 / 23, amplifier 15 |
| microSD / UART | GPIO 16 (MISO / TX), 17 (CS / RX) |
| Buttons | BOOT 9, PLUS 18, PWR |
| Battery | ETA6098, voltage on GPIO 0 |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-C6-Touch-LCD-1.54, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Battery voltage (ADC) |
| GPIO 1 | LCD SCK |
| GPIO 2 | LCD MOSI |
| GPIO 3 | LCD DC |
| GPIO 4 | LCD reset |
| GPIO 5 | Touch interrupt |
| GPIO 6 | Backlight |
| GPIO 7 | I2C SCL (touch, IMU, codecs) |
| GPIO 8 | I2C SDA (touch, IMU, codecs) |
| GPIO 9 | BOOT button |
| GPIO 10 | IMU interrupt |
| GPIO 11 | LCD CS |
| GPIO 12 | USB D- |
| GPIO 13 | USB D+ |
| GPIO 15 | Speaker amplifier enable |
| GPIO 16 | microSD MISO / UART TX |
| GPIO 17 | microSD CS / UART RX |
| GPIO 18 | PLUS button |
| GPIO 19 | I2S MCLK |
| GPIO 20 | I2S SCLK |
| GPIO 21 | I2S data out (ADC) |
| GPIO 22 | I2S LRCLK |
| GPIO 23 | I2S data in (codec) |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- The LCD Ultra Pro editor does not support it yet.
- microSD and UART share GPIO 16/17.
- The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
What it is good for
- •Zigbee voice remotes
- •Desk gadgets with sound
- •Square status displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (2MB APP/12.5MB FATFS) |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which pin is the backlight on the ESP32-C6-Touch-LCD-1.54?
GPIO 6.
Can I use the SD card and UART together?
No. GPIO 16 and 17 serve both the microSD slot and the UART pads.
Is there a non-touch version?
Yes, the ESP32-C6-LCD-1.54 without the CST816 touch controller.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare ESP32-C3 / C6 family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.