Waveshare · ESP32-C6 · 1.83" · 240×284
Waveshare ESP32-C6-Touch-LCD-1.83 specifications
This page collects the pinout and hardware details of the ESP32-C6-Touch-LCD-1.83. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
The S3 version of this board has a twin. The ESP32-C6-Touch-LCD-1.83 keeps the 240×284 ST7789P panel, the CST816D touch, the AXP2101 power manager and the ES8311 / ES7210 audio pair, and swaps the chip for an ESP32-C6 with Wi-Fi 6 and Zigbee / Thread.
The display wiring is different from the S3 board, so don't copy pins across. On the C6 the SPI clock is GPIO 1, MOSI 2, DC 3, reset 4, CS 5 and backlight 6. The shared I2C bus is on GPIO 7 (SDA) and 8 (SCL), and the touch interrupt on GPIO 9.
A QMI8658 IMU and a PCF85063 clock share that bus with the touch and power chips. There's a microSD slot, a speaker header and a microphone array, and the PWR button switches the board off after a six-second press. Reserved pads give you I2C, USB and GPIO 16/17.

- Screen
- 1.83" · 240×284
- Chip
- ESP32-C6
- Memory
- 16 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 1.83-inch, 240×284, ST7789P
- CST816D touch
- ESP32-C6: Wi-Fi 6, Zigbee, Thread
- AXP2101 PMU
- ES8311 + ES7210 audio
- QMI8658 IMU, PCF85063 RTC
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.83" |
| Resolution | 240×284 px |
| Colour depth | 16-bit |
| Display controller | ST7789P (SPI) |
| Display interface | SPI |
| Touch | CST816D (capacitive, I2C) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | AXP2101 PMU, QMI8658 IMU, PCF85063 RTC, ES8311 codec, ES7210 ADC with microphone array, speaker header, microSD. Reserved pads: I2C, USB, GPIO 16 and 17. PWR long-press (6 s) switches off. |
| Display | 240×284, ST7789P: SCK 1, MOSI 2, DC 3, RST 4, CS 5, backlight 6 |
| Touch | CST816D, INT 9 |
| I2C | SDA 7, SCL 8 |
| Spare pads | GPIO 16, 17, I2C, USB |
| Memory | 16 MB flash, no PSRAM |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-C6-Touch-LCD-1.83, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Speaker amplifier enable |
| GPIO 1 | SPI SCK (LCD, microSD) |
| GPIO 2 | SPI MOSI (LCD, microSD) |
| GPIO 3 | LCD DC |
| GPIO 4 | LCD reset / touch reset |
| GPIO 5 | LCD CS |
| GPIO 6 | Backlight |
| GPIO 7 | I2C SDA (touch, PMU, IMU, RTC, codecs) |
| GPIO 8 | I2C SCL (touch, PMU, IMU, RTC, codecs) |
| GPIO 9 | BOOT button |
| GPIO 10 | IMU interrupt |
| GPIO 11 | Touch interrupt |
| GPIO 15 | RTC interrupt |
| GPIO 16 | microSD MISO |
| GPIO 17 | microSD CS |
| GPIO 18 | PWR button |
| GPIO 19 | I2S MCLK |
| GPIO 20 | I2S SCLK |
| GPIO 21 | I2S ASDOUT (ES7210) |
| GPIO 22 | I2S LRCLK |
| GPIO 23 | I2S DSDIN (ES8311) |
Source: github.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- Not available in the LCD Ultra Pro editor yet.
- Pins differ from the ESP32-S3-Touch-LCD-1.83.
- The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
What it is good for
- •Voice remotes for Zigbee homes
- •Small smartwatch prototypes
- •Battery-powered status displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
Is it the same as the ESP32-S3-Touch-LCD-1.83?
Same screen and peripherals, but an ESP32-C6 chip and a different pin map.
Which pins drive the display?
SPI clock GPIO 1, MOSI 2, DC 3, reset 4, CS 5 and backlight 6.
How do I switch it off?
Hold the PWR button for about six seconds.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-C3 / C6 family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.