Waveshare · ESP32-C6 · 2.8" · 240×320
Waveshare ESP32-C6-Touch-LCD-2.8 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-C6-Touch-LCD-2.8. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Four free GPIOs and four more on an expander. That's the unusual part of the ESP32-C6-Touch-LCD-2.8: Waveshare moved the slow signals (LCD reset, touch reset, RTC interrupt, amplifier enable, backlight PWM and battery voltage) onto a small CH32 microcontroller acting as an I/O expander, which leaves GPIO 4, 5, 21 and 22 untouched.
The 240×320 screen and the microSD card share one SPI bus: clock GPIO 0, MOSI 1, MISO 8, with LCD CS 11 and DC 10, and card CS 23. Touch, IMU, clock, codec and expander all use I2C on GPIO 6 and 7, and the touch interrupt is GPIO 18.
Sensors are generous for the price: a QMI8658 IMU, a PCF85063A clock and an SHTC3 for temperature and humidity. Audio is an ES8311 with an NS4150B amplifier. The chip is an ESP32-C6-WROOM-1 module with 16 MB of flash.

- Screen
- 2.8" · 240×320
- Chip
- ESP32-C6
- Memory
- 16 MB flash, no PSRAM
- Input
- capacitive touch
Key features
- 2.8-inch, 240×320 SPI LCD
- Capacitive touch
- ESP32-C6-WROOM-1, 16 MB
- CH32 I/O expander (EXIO4-7 free)
- QMI8658, PCF85063A, SHTC3
- GPIO 4, 5, 21, 22 free
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 2.8" |
| Resolution | 240×320 px |
| Colour depth | 16-bit |
| Display controller | SPI LCD |
| Display interface | SPI |
| Touch | Capacitive (I2C) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6-WROOM-1 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | A CH32 I/O expander handles touch reset, LCD reset, RTC interrupt, speaker amplifier enable, backlight PWM and battery voltage (EXIO4-7 free). QMI8658 IMU, PCF85063A RTC, SHTC3 sensor, ES8311 codec with NS4150B amplifier, microSD sharing the LCD SPI bus. |
| Display | SCK 0, MOSI 1, DC 10, CS 11; reset and backlight via the expander |
| Touch | I2C SDA 6 / SCL 7, INT 18 |
| microSD | SCK 0, MOSI 1, MISO 8, CS 23 |
| Audio | I2S SCLK 15, LRCK 3, DOUT 2, DIN 20 |
| Free GPIO | 4, 5, 21, 22; UART0 16 / 17 |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | SPI SCK (LCD, microSD) |
| GPIO 1 | SPI MOSI (LCD, microSD) |
| GPIO 2 | I2S data out |
| GPIO 3 | I2S LRCLK |
| GPIO 4 | Free GPIO |
| GPIO 5 | Free GPIO |
| GPIO 6 | I2C SDA (touch, IMU, RTC, codec, expander) |
| GPIO 7 | I2C SCL (touch, IMU, RTC, codec, expander) |
| GPIO 8 | microSD MISO |
| GPIO 9 | BOOT button |
| GPIO 10 | LCD DC |
| GPIO 11 | LCD CS |
| GPIO 12 | USB D- |
| GPIO 13 | USB D+ |
| GPIO 15 | I2S SCLK |
| GPIO 16 | UART0 TX |
| GPIO 17 | UART0 RX |
| GPIO 18 | Touch interrupt |
| GPIO 19 | IMU interrupt |
| GPIO 20 | I2S data in |
| GPIO 21 | Free GPIO |
| GPIO 22 | Free GPIO |
| GPIO 23 | microSD CS |
Source: github.com, docs.waveshare.com, github.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 4 | GPIO, PWM, ADC | On the pin-out header |
| GPIO 5 | GPIO, PWM, ADC | On the pin-out header |
| GPIO 21 | GPIO, PWM | On the pin-out header |
| GPIO 22 | GPIO, PWM | On the pin-out header |
| GPIO 16 | GPIO, UART_TX | UART0 TX on the pin-out header |
| GPIO 17 | GPIO, UART_RX | UART0 RX on the pin-out header |
- Pin-out header — GPIO 4, 5, 6, 7, 9, 12, 13, 16, 17, 21, 22 · pin header
GPIO 6 / 7 are the on-board I2C bus (SDA / SCL), 9 is BOOT, 12 / 13 native USB; also CHIP_PU and the expander lines
Good to know before you start
- Not in the LCD Ultra Pro editor yet.
- Backlight and LCD reset need the CH32 expander driver.
- The ESP32-C6 has no PSRAM, so keep LVGL buffers to a fraction of the screen.
What it is good for
- •Zigbee room sensors with a display
- •Climate panels (SHTC3 on board)
- •Projects that need a few spare GPIOs
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|---|
| Flash Size | 16 MB |
| Flash Mode | QIO |
| PSRAM | Not supported (the board has no PSRAM) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which GPIOs are free on the ESP32-C6-Touch-LCD-2.8?
GPIO 4, 5, 21 and 22, plus EXIO4 to EXIO7 on the CH32 expander.
How is the backlight controlled?
By PWM from the CH32 I/O expander, not by an ESP32-C6 pin.
Does it have a temperature sensor?
Yes, an SHTC3 for temperature and humidity on the I2C bus.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
- https://github.com/waveshareteam/ESP32-C6-Touch-LCD-2.8
- https://docs.waveshare.com/ESP32-C6-Touch-LCD-2.8
- https://www.waveshare.com/esp32-c6-touch-lcd-2.8.htm
- https://github.com/waveshareteam/ESP32-C6-Touch-LCD-2.8/blob/main/hardware/schematic/ESP32-C6-Touch-LCD-2.8.pdf
- https://docs.waveshare.com/ESP32-C6-Touch-LCD-2.8/Arduino
More in the Waveshare ESP32-C3 / C6 family
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.