Waveshare · ESP32-C6 · 1.9" · 170×320
Waveshare ESP32-C6-LCD-1.9 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-C6-LCD-1.9. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
This is the C6 counterpart of the ESP32-S3-LCD-1.9: the same bright 170×320 ST7789V2 strip at 500 cd/m² on a Pico-compatible footprint, but with an ESP32-C6FH8 that carries 8 MB of flash inside the chip and adds Wi-Fi 6.
Waveshare's own pages disagree on the chip name, calling it ESP32-C6FH8 in one place and C6R8 in another. The memory spec is consistent though: 8 MB of stacked flash and no PSRAM.
On the board are a QMI8658 IMU, a TCA9554 8-channel I/O expander, a WS2812 RGB LED on the back (non-touch version), a microSD slot and a 3.7 V battery connector with charging. A touch version with a CST816 and an IPEX antenna option is also sold. The full GPIO table is below; GPIO 3, 21, 22 and 23 are free on the header.

- Screen
- 1.9" · 170×320
- Chip
- ESP32-C6
- Memory
- 8 MB flash, no PSRAM
- Input
- no touch
Key features
- 1.9-inch, 170×320, ST7789V2, 500 cd/m²
- ESP32-C6FH8, 8 MB flash, Wi-Fi 6
- QMI8658 IMU
- TCA9554 I/O expander
- WS2812 LED, microSD
- Pico-compatible headers
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.9" |
| Resolution | 170×320 px |
| Colour depth | 16-bit |
| Display controller | ST7789V2 (SPI) |
| Display interface | SPI |
| Touch | None (touch version: ESP32-C6-Touch-LCD-1.9, CST816) |
| Microcontroller | ESP32-C6 |
| Module | ESP32-C6FH8 |
| CPU clock | 160 MHz |
| Internal SRAM | 512 KB |
| PSRAM | None |
| Flash | 8 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | ESP32-C6FH8 with 8 MB in-package flash. QMI8658 IMU, TCA9554 I/O expander, WS2812 LED (non-touch version), microSD, battery charging, Pico-compatible headers. GPIO table published only as an image. |
| Display | 170×320, ST7789V2 (SPI) |
| Chip | ESP32-C6FH8, 8 MB in-package flash, no PSRAM |
| Sensors | QMI8658 IMU |
| Power | MX1.25 3.7 V lithium, charging LED |
| Variants | ESP32-C6-LCD-1.9 and ESP32-C6-Touch-LCD-1.9 |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | Battery voltage (ADC) |
| GPIO 1 | IMU interrupt 1 |
| GPIO 2 | IMU interrupt 2 |
| GPIO 3 | Header GPIO |
| GPIO 4 | SPI MOSI (LCD, microSD) |
| GPIO 5 | SPI SCK (LCD, microSD) |
| GPIO 6 | LCD DC |
| GPIO 7 | LCD CS |
| GPIO 8 | I2C SCL (IMU, expander) |
| GPIO 9 | BOOT button |
| GPIO 12 | Header GPIO / USB D- |
| GPIO 13 | Header GPIO / USB D+ |
| GPIO 14 | LCD reset |
| GPIO 15 | Backlight |
| GPIO 16 | UART0 TX |
| GPIO 17 | UART0 RX |
| GPIO 18 | I2C SDA (IMU, expander) |
| GPIO 19 | microSD MISO |
| GPIO 20 | microSD CS |
| GPIO 21 | Header GPIO |
| GPIO 22 | Header GPIO |
| GPIO 23 | Header GPIO |
Source: github.com, docs.waveshare.com, www.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 3 | GPIO, PWM, ADC | On the header |
| GPIO 12 | GPIO, PWM | On the header; also USB D- |
| GPIO 13 | GPIO, PWM | On the header; also USB D+ |
| GPIO 21 | GPIO, PWM | On the header |
| GPIO 22 | GPIO, PWM | On the header |
| GPIO 23 | GPIO, PWM | On the header |
| GPIO 16 | GPIO, UART_TX | UART0 TX on the header |
| GPIO 17 | GPIO, UART_RX | UART0 RX on the header |
- Pico-style pin headers — GPIO 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23 · 2 x 20 pin header
Also EXIO0-7 of the TCA9554 expander
Good to know before you start
- It's not supported in the LCD Ultra Pro editor yet.
- Only 8 MB flash and no PSRAM.
- GPIO 12 / 13 are native USB; use them as GPIO only if you don't need USB.
What it is good for
- •Breadboard projects with Wi-Fi 6
- •Status strips
- •Learning the ESP32-C6
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32C6 Dev Module |
|---|
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
How much flash does the ESP32-C6-LCD-1.9 have?
8 MB, inside the ESP32-C6FH8 chip.
Is there a touch version?
Yes, the ESP32-C6-Touch-LCD-1.9 with a CST816 controller.
What is the TCA9554 for?
It is an 8-channel I/O expander on the I2C bus that adds extra control lines.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-C3 / C6 family
- Waveshare ESP32-C6-LCD-0.85
- Waveshare ESP32-C6 1.3" LCD
- Waveshare ESP32-C3 1.47" LCD
- Waveshare ESP32-C6 1.47" LCD
- Waveshare ESP32-C6 Touch LCD 1.47"
- Waveshare ESP32-C6-Touch-LCD-1.54
- Waveshare ESP32-C6 Touch LCD 1.69"
- Waveshare ESP32-C6-Touch-LCD-1.83
- Waveshare ESP32-C6-LCD-2.73
- Waveshare ESP32-C6-Touch-LCD-2.8
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.