Waveshare · ESP32-S3 · 1.83" · 240×284
Waveshare ESP32-S3-Touch-LCD-1.83 specifications
This page collects the pinout and hardware details of the ESP32-S3-Touch-LCD-1.83. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
240×284 is an odd resolution, and it's the first thing to set right if you port code from the 1.69-inch board. The 1.83-inch panel uses an ST7789P on SPI with the same four signal pins (SCK 6, MOSI 7, CS 5, DC 4), but reset, backlight and touch moved.
The bigger change is what Waveshare added around it. An AXP2101 power-management chip replaces the simple charger, and there's a full audio path: ES8311 codec for the speaker, ES7210 ADC for the microphone array, with an amplifier enabled on GPIO 46. A QMI8658 IMU, a PCF85063 clock and a microSD slot (1-bit SDMMC on GPIO 1 to 3) complete it.
Everything that talks I2C shares GPIO 14/15. Waveshare's managed ESP-IDF component, waveshare/esp32_s3_touch_lcd_1_83, sets all of this up, and it's where the pin numbers on this page come from. The ten reserved GPIO pads are documented only as a picture, so they aren't listed here.

- Screen
- 1.83" · 240×284
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.83-inch LCD, 240×284, ST7789P
- CST816D capacitive touch
- AXP2101 power management
- ES8311 codec and ES7210 microphone ADC
- QMI8658 IMU, PCF85063 RTC
- microSD slot
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.83" |
| Resolution | 240×284 px |
| Colour depth | 16-bit |
| Display controller | ST7789P (SPI) |
| Display interface | SPI |
| Touch | CST816D (capacitive, I2C) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | AXP2101 PMU, QMI8658 IMU, PCF85063 RTC, ES8311 codec and ES7210 microphone ADC. Waveshare lists 10 reserved GPIO pads plus I2C, USB and UART pads, but publishes their GPIO numbers only as an image. |
| Display | 240×284, ST7789P (SPI): SCK 6, MOSI 7, CS 5, DC 4, RST 38, backlight 40 |
| Touch | CST816D, INT 13, RST 39 |
| Audio | I2S MCLK 16, SCLK 9, LRCLK 45, DOUT 8, DIN 10; amplifier enable 46 |
| I2C | SDA 15, SCL 14: touch, PMU, IMU, RTC, codecs |
| Storage | microSD: CMD 1, CLK 2, D0 3 |
| Memory | 16 MB flash, 8 MB PSRAM |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-Touch-LCD-1.83, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | microSD MOSI |
| GPIO 2 | microSD SCK |
| GPIO 3 | microSD MISO |
| GPIO 4 | LCD DC |
| GPIO 5 | LCD CS |
| GPIO 6 | LCD SCK |
| GPIO 7 | LCD MOSI |
| GPIO 8 | I2S data out (ES8311) |
| GPIO 9 | I2S SCLK |
| GPIO 10 | I2S data in (ES7210) |
| GPIO 11 | IMU interrupt 1 |
| GPIO 12 | RTC interrupt |
| GPIO 13 | Touch interrupt |
| GPIO 14 | I2C SCL (touch, PMU, IMU, RTC, codecs) |
| GPIO 15 | I2C SDA (touch, PMU, IMU, RTC, codecs) |
| GPIO 16 | I2S MCLK |
| GPIO 21 | IMU interrupt 2 |
| GPIO 38 | LCD reset |
| GPIO 39 | Touch reset |
| GPIO 40 | Backlight |
| GPIO 41 | PWR button |
| GPIO 42 | microSD CS |
| GPIO 45 | I2S LRCLK |
| GPIO 46 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
This board has no free GPIOs: every pin is used by the display, touch or on-board peripherals.
Good to know before you start
- The LCD Ultra Pro editor doesn't include this board yet.
- Different pins from the 1.69-inch board apart from the SPI lines. Don't reuse a 1.69 config.
- The AXP2101 must be set up before some rails turn on. The BSP does it for you.
What it is good for
- •Voice assistants on a wrist-sized screen
- •Smartwatch prototypes with sound
- •Small audio players
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Frequently asked questions
What is the resolution of the ESP32-S3-Touch-LCD-1.83?
240×284 pixels on an ST7789P controller.
Does it have a microphone?
Yes. An ES7210 ADC handles the onboard microphone array, and an ES8311 codec drives the speaker output.
Is there an ESP-IDF board package?
Yes, the managed component waveshare/esp32_s3_touch_lcd_1_83 in Waveshare's component repository.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.