Waveshare · ESP32-S3 · 4.2" · 300×400
Waveshare ESP32-S3-RLCD-4.2 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-RLCD-4.2. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
No backlight. The RLCD-4.2 uses a reflective LCD, which works like a paper display in daylight: the brighter the room, the better it looks. Unlike e-paper, it refreshes like a normal LCD, so you can show a clock with seconds without the flicker of a full e-ink update.
The panel is 300×400 and driven by an ST7305 over SPI (SCK 11, MOSI 12, CS 40, DC 5, reset 41, TE 6). It's monochrome, so think in black and white. The examples include a U8g2 test as well as LVGL 8 and 9.
The rest of the board is built for a self-contained device: ESP32-S3-WROOM-1-N16R8, ES8311 codec and ES7210 ADC with two microphones, a speaker header, a PCF85063 clock with its own backup cell, an SHTC3 temperature and humidity sensor, a microSD slot and an 18650 battery holder with charging. A KEY button on GPIO 18 is free for your code. Power draw without a backlight makes it a good fit for battery-run weather stations.

- Screen
- 4.2" · 300×400
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- no touch
Key features
- 4.2-inch reflective LCD, 300×400, no backlight
- ST7305 controller over SPI
- ESP32-S3-WROOM-1-N16R8
- ES8311 + ES7210 audio, two microphones
- PCF85063 RTC, SHTC3 sensor
- 18650 battery holder with charging
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 4.2" |
| Resolution | 300×400 px |
| Colour depth | 1-bit |
| Display controller | ST7305 (SPI, reflective) |
| Display interface | SPI |
| Touch | None |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3-WROOM-1-N16R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Reflective LCD: readable in daylight without a backlight. ES8311 codec, ES7210 dual-microphone ADC, speaker header, PCF85063 RTC with its own backup cell, SHTC3 temperature and humidity sensor, 18650 holder, 2 x 8 female header. V1 and V2 differ in case thickness (13.5 vs 14.1 mm). |
| Display | 300×400 reflective, ST7305: SCK 11, MOSI 12, CS 40, DC 5, RST 41, TE 6 |
| I2C | SDA 13, SCL 14: RTC, SHTC3, codecs |
| Buttons | BOOT (GPIO 0), KEY (GPIO 18), PWR |
| Power | 18650 holder, charge and warning LEDs |
| Expansion | 2 × 8 female header, 2.54 mm |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Unassigned GPIO |
| GPIO 2 | Unassigned GPIO |
| GPIO 3 | Unassigned GPIO |
| GPIO 4 | Battery voltage (ADC) |
| GPIO 5 | LCD DC |
| GPIO 6 | LCD tearing effect (TE) |
| GPIO 7 | TP_INT line of the display connector |
| GPIO 8 | I2S DSDIN (ES8311) |
| GPIO 9 | I2S SCLK |
| GPIO 10 | I2S ASDOUT (ES7210) |
| GPIO 11 | LCD SCK |
| GPIO 12 | LCD MOSI |
| GPIO 13 | I2C SDA (RTC, sensor, codecs) |
| GPIO 14 | I2C SCL (RTC, sensor, codecs) |
| GPIO 15 | RTC interrupt |
| GPIO 16 | I2S MCLK |
| GPIO 17 | Header GPIO |
| GPIO 18 | User key |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 21 | microSD MOSI |
| GPIO 38 | microSD SCK |
| GPIO 39 | microSD MISO |
| GPIO 40 | LCD CS |
| GPIO 41 | LCD reset |
| GPIO 42 | TP_RESET line of the display connector |
| GPIO 43 | UART0 TX (header) |
| GPIO 44 | UART0 RX (header) |
| GPIO 45 | I2S LRCLK |
| GPIO 46 | Speaker amplifier enable |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 17 | GPIO, PWM, ADC | On the 2 x 8 header |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the header |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the header |
| GPIO 1 | GPIO, PWM, ADC | Not assigned in Waveshare's GPIO table |
| GPIO 2 | GPIO, PWM, ADC | Not assigned in Waveshare's GPIO table |
| GPIO 3 | GPIO, PWM, ADC | Not assigned in Waveshare's GPIO table |
- Expansion header (OUT) — GPIO 13, 14, 17, 43, 44 (SDA, SCL, GPIO, TX, RX) · 2 x 8 female, 2.54 mm
GPIO 13/14 are the on-board I2C bus (RTC, sensor, codecs)
Good to know before you start
- The LCD Ultra Pro editor can't target this board yet.
- It is monochrome. Colour UI designs will not carry over.
- In a dark room you see nothing; there is no light source.
What it is good for
- •Weather stations and room climate displays
- •Always-on clocks and calendars
- •Outdoor status panels
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Does the ESP32-S3-RLCD-4.2 have a backlight?
No. It uses a fully reflective LCD that needs ambient light.
Is it e-paper?
No. It is a reflective LCD driven by an ST7305, so it updates like a normal LCD without e-ink refresh flicker.
Which sensors are on board?
An SHTC3 temperature and humidity sensor and a PCF85063 RTC.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.