Waveshare · ESP32-S3 · 1.69" · 240×280
Waveshare ESP32-S3-Touch-LCD-1.69 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-Touch-LCD-1.69. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Small rectangular screens with rounded corners are what most people picture for a DIY smartwatch, and this Waveshare board is built for exactly that. The 1.69-inch panel is 240×280, driven by an ST7789V2 over SPI, with a CST816T touch controller at 0x15.
There's a lot on a little board. An ESP32-S3R8 with 16 MB flash and 8 MB PSRAM, a QMI8658C six-axis IMU, a PCF85063 real-time clock, a buzzer and an ETA6098 charger for a single lithium cell. The power button doesn't just reset the chip: GPIO 41 holds the supply on and GPIO 40 reads the button, so firmware can switch the board off.
Watch out for revisions. Waveshare's key and buzzer example carries two pin sets, and older boards use GPIO 33, 35 and 36 instead of 42, 41 and 40. The documentation table matches the newer one. The expansion header gives you four plain GPIOs (2, 3, 17, 18), the I2C bus and UART0.

- Screen
- 1.69" · 240×280
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 1.69-inch LCD, 240×280, ST7789V2 (SPI)
- CST816T capacitive touch
- ESP32-S3R8: 16 MB flash, 8 MB PSRAM
- QMI8658C IMU and PCF85063 RTC
- Buzzer and software power-off
- Lithium battery charging (ETA6098)
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.69" |
| Resolution | 240×280 px |
| Colour depth | 16-bit |
| Display controller | ST7789V2 (SPI) |
| Display interface | SPI |
| Touch | CST816T (capacitive, I2C 0x15) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Current documentation pin table. Older boards used GPIO 36 / 35 / 33 for the power button, power hold and buzzer; Waveshare's key/buzzer example has a switch for both versions. QMI8658C IMU (0x6B) and PCF85063 RTC (0x51) on the I2C bus, ETA6098 charger. |
| Display | 1.69-inch, 240×280, ST7789V2: SCK 6, MOSI 7, CS 5, DC 4, RST 8, backlight 15 |
| Touch | CST816T at 0x15, INT 14, RST 13 |
| I2C bus | SDA 11, SCL 10: touch, IMU (0x6B), RTC (0x51) |
| Power | Battery ADC on GPIO 1, power hold GPIO 41, button sense GPIO 40 |
| Header | GPIO 2, 3, 17, 18, I2C, UART0 (43/44), 5 V, 3.3 V, GND |
| Buzzer | GPIO 42 on current boards |
Board layout and connectors
Where each connector, button and LED sits on the Waveshare ESP32-S3-Touch-LCD-1.69, with the pin order next to each header where the manufacturer confirms it. We drew it from the manufacturer’s own photos and board documentation. The tiny parts are simplified.


GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Battery voltage (ADC) |
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | LCD DC |
| GPIO 5 | LCD CS |
| GPIO 6 | LCD SCK |
| GPIO 7 | LCD MOSI |
| GPIO 8 | LCD reset |
| GPIO 10 | I2C SCL (touch, IMU, RTC, header) |
| GPIO 11 | I2C SDA (touch, IMU, RTC, header) |
| GPIO 13 | Touch reset |
| GPIO 14 | Touch interrupt |
| GPIO 15 | Backlight |
| GPIO 17 | Header GPIO |
| GPIO 18 | Header GPIO |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 38 | IMU interrupt |
| GPIO 39 | RTC interrupt |
| GPIO 40 | Power button sense (SYS_OUT) |
| GPIO 41 | Power hold (SYS_EN) |
| GPIO 42 | Buzzer |
| GPIO 43 | UART0 TX (header) |
| GPIO 44 | UART0 RX (header) |
Source: github.com, docs.waveshare.com, github.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 2 | GPIO, PWM, ADC | On the expansion header |
| GPIO 3 | GPIO, PWM, ADC | On the expansion header |
| GPIO 17 | GPIO, PWM, ADC | On the expansion header |
| GPIO 18 | GPIO, PWM, ADC | On the expansion header |
| GPIO 43 | GPIO, UART_TX | UART0 TX on the expansion header |
| GPIO 44 | GPIO, UART_RX | UART0 RX on the expansion header |
- Expansion header — GPIO 2, 3, 17, 18, 10, 11, 43, 44 · pin header
Also 5 V, 3.3 V and GND; GPIO 10/11 are the on-board I2C bus
Good to know before you start
- Not in the LCD Ultra Pro editor yet; there's no export for this board from us.
- If the buttons or buzzer don't respond, you probably have the older pin layout. Try the alternate set in Waveshare's example.
- Battery voltage reads on GPIO 1 through a 1:3 divider.
- GPIO 19/20 are the USB port. Leave them alone.
What it is good for
- •DIY smartwatches and fitness trackers
- •Pocket timers and step counters
- •Battery-powered remotes with motion input
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| Flash Size | 16MB (128Mb) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems 3.3.11
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Which GPIOs are free on the ESP32-S3-Touch-LCD-1.69?
GPIO 2, 3, 17 and 18 on the expansion header, plus UART0 on GPIO 43/44 if you don't need the serial console there.
What does the power button do?
It drives a small latch circuit. GPIO 41 keeps the board powered and GPIO 40 reads the button, so your code can turn the board off.
Is there a difference between hardware versions?
Yes. Older boards use GPIO 36, 35 and 33 for the button sense, power hold and buzzer; current ones use 40, 41 and 42.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-03):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3-Touch-LCD-3.49
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.