Waveshare · ESP32-S3 · 3.49" · 172×640
Waveshare ESP32-S3-Touch-LCD-3.49 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-Touch-LCD-3.49. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
A 172×640 strip is a strange shape until you need a status bar under a monitor or a narrow panel in a rack. That's this board. The 3.49-inch IPS panel is driven by an AXS15231B, which handles both display (QSPI) and touch (I2C at 0x3B) in one chip.
Waveshare's own documentation contradicts itself on the resolution, listing 172×320 in one place and 172×640 in another. The example code settles it at 172×640.
There are two hardware versions, and they matter. V2, marked Rev1.1 on the PCB and shipping since June 2026, swaps the LCD TE and reset lines, swaps the backlight with the expander interrupt, and moves the backlight pin. Code for the wrong version leaves the screen dark. The QSPI data lines (GPIO 9 to 14), touch I2C (17/18), sensor I2C (47/48) and microSD (39 to 41) are the same on both. The board also carries ES8311 and ES7210 audio, a PCF85063 clock, a QMI8658 IMU and a TCA9554 expander.

- Screen
- 3.49" · 172×640
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- capacitive touch
Key features
- 3.49-inch IPS bar, 172×640
- AXS15231B: QSPI display and touch in one chip
- ESP32-S3R8, 16 MB flash, 8 MB PSRAM
- ES8311 + ES7210 audio with dual microphones
- PCF85063 RTC, QMI8658 IMU, TCA9554 expander
- 22-pin 2.54 mm expansion pads
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 3.49" |
| Resolution | 172×640 px |
| Colour depth | 16-bit |
| Display controller | AXS15231B (QSPI) |
| Display interface | QSPI |
| Touch | AXS15231B integrated touch (I2C 0x3B) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3R8 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | V2 (PCB "Rev1.1", shipped from 2026-06-08) swaps LCD_TE/LCD_RESET and LCD_BL/EXIO_INT compared with V1 and moves the backlight pin; those pins are left out here, use the example for your version. TCA9554 IO expander, PCF85063 RTC (0x51), QMI8658 IMU (0x6B), ES8311 + ES7210 audio. The 3.49B variant ships in a case. |
| Display | 172×640 IPS, AXS15231B (QSPI: CS 9, CLK 10, D0-D3 11 to 14), 350 cd/m² |
| Touch | Integrated in the AXS15231B, I2C 0x3B on GPIO 17 (SDA) / 18 (SCL) |
| Sensor I2C | SDA 47, SCL 48: RTC (0x51), IMU (0x6B), expander, codecs |
| microSD | CLK 41, CMD 39, D0 40 |
| Keys | BOOT (GPIO 0), user key on GPIO 16 |
| Variants | 3.49 (Case A, 18650 cell) and 3.49B (Case B, LiPo) |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation. Pins whose function isn’t stated clearly are left out.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Header GPIO |
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | Battery voltage (ADC) |
| GPIO 5 | Header GPIO |
| GPIO 6 | I2S DSOUT |
| GPIO 7 | I2S MCLK |
| GPIO 9 | LCD CS |
| GPIO 10 | LCD QSPI clock |
| GPIO 11 | LCD data 0 |
| GPIO 12 | LCD data 1 |
| GPIO 13 | LCD data 2 |
| GPIO 14 | LCD data 3 |
| GPIO 15 | I2S SCLK |
| GPIO 16 | PWR button sense (SYS_OUT) |
| GPIO 17 | Touch I2C SDA |
| GPIO 18 | Touch I2C SCL |
| GPIO 19 | USB D- |
| GPIO 20 | USB D+ |
| GPIO 38 | microSD CS |
| GPIO 39 | microSD MOSI |
| GPIO 40 | microSD MISO |
| GPIO 41 | microSD SCK |
| GPIO 43 | UART0 TX |
| GPIO 44 | UART0 RX |
| GPIO 45 | I2S DSDIN |
| GPIO 46 | I2S LRCLK |
| GPIO 47 | I2C SDA (RTC, IMU, IO expander, codecs) |
| GPIO 48 | I2C SCL (RTC, IMU, IO expander, codecs) |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 1 | GPIO, PWM, ADC | On the 22-pin header |
| GPIO 2 | GPIO, PWM, ADC | On the 22-pin header |
| GPIO 3 | GPIO, PWM, ADC | On the 22-pin header |
| GPIO 5 | GPIO, PWM, ADC | On the 22-pin header |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the header |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the header |
- Expansion header — GPIO 0, 1, 2, 3, 4, 5, 6, 7, 15, 16, 17, 18, 19, 20, 38, 39, 40, 41, 43, 44, 45, 46, 47, 48 · 22-pin 2.54 mm pads
Also EXIO0-7 of the TCA9554 expander. GPIO 8, 21 and 42 swap roles between V1 and V2, so they are left out
Good to know before you start
- This bar display isn't supported in the LCD Ultra Pro editor yet.
- Check the PCB for "Rev1.1". It decides the backlight and reset pins.
- Plan your layout for 172 pixels of height in landscape. Two lines of large text is about it.
- Antenna: an IPEX connector exists, but it needs an onboard resistor moved.
What it is good for
- •PC monitor status bars (CPU, network, weather)
- •Rack and shelf labels
- •Audio meters and tickers
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Mode | QIO 80MHz |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
What resolution is the ESP32-S3-Touch-LCD-3.49?
172×640. The documentation mentions 172×320 in one table, but the example code uses 172×640.
How do I tell V1 and V2 apart?
V2 has "Rev1.1" printed on the PCB or a "V2" label on the case QC sticker. Boards shipped from 8 June 2026 are V2.
Which touch controller is used?
None separate: the AXS15231B display driver includes touch, read over I2C at address 0x3B.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare ESP32-S3 LCD family
- Waveshare ESP32-S3-LCD-0.85
- Waveshare ESP32-S3 LCD 1.3"
- Waveshare ESP32-S3 LCD 1.47" Type B
- Waveshare ESP32-S3 Touch LCD 1.47"
- Waveshare ESP32-S3-Touch-LCD-1.54
- Waveshare ESP32-S3-Touch-LCD-1.69
- Waveshare ESP32-S3-Touch-LCD-1.83
- Waveshare ESP32-S3-LCD-1.9
- Waveshare ESP32-S3 Touch LCD 2.0"
- Waveshare ESP32-S3 Touch LCD 2.8"
- Waveshare ESP32-S3 Touch LCD 2.8" Type B
- Waveshare ESP32-S3-Touch-LCD-2.8D
- Waveshare ESP32-S3 LCD 3.16"
- Waveshare ESP32-S3 Touch LCD 3.5"
- Waveshare ESP32-S3 Touch LCD 3.5" Type B
- Waveshare ESP32-S3 Touch LCD 4.0"
- Waveshare ESP32-S3-Touch-LCD-4B
- Waveshare ESP32-S3-RLCD-4.2
- Waveshare ESP32-S3 Touch LCD 4.3"
- Waveshare ESP32-S3 Touch LCD 4.3" Type B
- Waveshare ESP32-S3 Touch LCD 4.3" Type C
- Waveshare ESP32-S3 Touch LCD 5.0"
- Waveshare ESP32-S3 Touch LCD 7.0"
- Waveshare ESP32-S3-Touch-LCD-7B
- Waveshare ESP32-S3-Touch-LCD-7C
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.