Waveshare · ESP32-S3 · 1.91" · 536×240
Waveshare ESP32-S3-AMOLED-1.91 specifications
This page collects the pinout, free GPIOs and hardware details of the ESP32-S3-AMOLED-1.91. The board isn't in the LCD Ultra Pro™ editor yet, so there's no driver for it there.
Four boards share this name. The plain ESP32-S3-AMOLED-1.91 has no touch and no header, the -M version adds pin headers, and Touch-AMOLED-1.91 and Touch-AMOLED-1.91-M add a five-point capacitive panel. Pick the right one before you order, because touch can't be added later.
All of them use a 1.91-inch AMOLED at 536×240, a wide stick-shaped screen, driven over QSPI. Waveshare's examples put CS on GPIO 6, clock on 47, data on 18, 7, 48 and 5, and reset on 17.
On the board there's an ESP32-S3 with 16 MB of flash and 8 MB of PSRAM, a QMI8658 IMU and a PCF85063 clock on the I2C bus (GPIO 40/39), plus a microSD slot. The Touch version reports touch events on GPIO 41. One practical note from Waveshare's README: the playful demo set needs an arduino-esp32 core older than 3.0.

- Screen
- 1.91" · 536×240
- Chip
- ESP32-S3
- Memory
- 16 MB flash, 8 MB PSRAM (OPI)
- Input
- no touch
Key features
- 1.91-inch AMOLED, 536×240, QSPI
- Touch and header versions available
- ESP32-S3, 16 MB flash, 8 MB PSRAM
- QMI8658 IMU and PCF85063 RTC
- microSD slot
Specifications
| Manufacturer | Waveshare |
|---|---|
| Screen size | 1.91" |
| Resolution | 536×240 px |
| Colour depth | 16-bit |
| Display controller | QSPI AMOLED |
| Display interface | QSPI |
| Touch | None (touch version: ESP32-S3-Touch-AMOLED-1.91) |
| Microcontroller | ESP32-S3 |
| Module | ESP32-S3 |
| CPU clock | 240 MHz |
| Internal SRAM | 512 KB |
| PSRAM | 8 MB (OPI) |
| Flash | 16 MB |
| Wi-Fi | Yes |
| Bluetooth | Yes |
| Hardware variant | Four versions: ESP32-S3-AMOLED-1.91 (no touch, no header), -M (header), Touch-AMOLED-1.91 (touch) and Touch-AMOLED-1.91-M (touch and header). QMI8658 IMU, PCF85063 RTC, microSD slot. The touch version reports touch on GPIO 41. |
| Display | 536×240 AMOLED, QSPI: CS 6, CLK 47, D0 18, D1 7, D2 48, D3 5, RST 17 |
| I2C | SDA 40, SCL 39 |
| Touch | Touch versions only, interrupt on GPIO 41 |
| Versions | AMOLED-1.91, AMOLED-1.91-M, Touch-AMOLED-1.91, Touch-AMOLED-1.91-M |
| Storage | microSD slot |
GPIO pinout
The GPIOs the board itself uses for the display, touch and on-board peripherals, as published in the manufacturer’s documentation.
| GPIO | Function |
|---|---|
| GPIO 0 | BOOT button |
| GPIO 1 | Battery voltage (ADC) |
| GPIO 2 | Header GPIO |
| GPIO 3 | Header GPIO |
| GPIO 4 | Header GPIO |
| GPIO 5 | LCD data 3 |
| GPIO 6 | LCD CS |
| GPIO 7 | LCD data 1 |
| GPIO 8 | microSD MISO |
| GPIO 9 | microSD CS |
| GPIO 10 | Header GPIO |
| GPIO 11 | Header GPIO |
| GPIO 12 | Header GPIO |
| GPIO 13 | Header GPIO |
| GPIO 14 | Header GPIO |
| GPIO 15 | Header GPIO |
| GPIO 16 | Header GPIO (LCD TE, not connected by default) |
| GPIO 17 | Header GPIO (LCD reset, not connected by default) |
| GPIO 18 | LCD data 0 |
| GPIO 19 | USB D- (header) |
| GPIO 20 | USB D+ (header) |
| GPIO 21 | Header GPIO |
| GPIO 26 | Header GPIO |
| GPIO 33 | Octal PSRAM (on the header, not usable) |
| GPIO 34 | Octal PSRAM (on the header, not usable) |
| GPIO 35 | Octal PSRAM (on the header, not usable) |
| GPIO 36 | Octal PSRAM (on the header, not usable) |
| GPIO 37 | Octal PSRAM (on the header, not usable) |
| GPIO 38 | Header GPIO |
| GPIO 39 | I2C SCL (IMU, touch) |
| GPIO 40 | I2C SDA (IMU, touch) |
| GPIO 41 | Touch interrupt (touch versions) |
| GPIO 42 | microSD MOSI |
| GPIO 43 | UART0 TX (header) |
| GPIO 44 | UART0 RX (header) |
| GPIO 45 | IMU interrupt 1 |
| GPIO 46 | IMU interrupt 2 |
| GPIO 47 | LCD QSPI clock / microSD CLK |
| GPIO 48 | LCD data 2 |
Source: github.com, docs.waveshare.com, docs.waveshare.com. Always check against your board revision before wiring.
Free GPIOs and connectors
These GPIOs are not used by the display, touch or on-board peripherals, so you can wire your own sensors, buttons or relays to them.
| Pin | Capabilities | Note |
|---|---|---|
| GPIO 2 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 3 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 4 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 10 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 11 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 12 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 13 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 14 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 15 | GPIO, PWM, ADC | On the 40-pin header (-M versions) |
| GPIO 21 | GPIO, PWM | On the 40-pin header (-M versions) |
| GPIO 26 | GPIO, PWM | On the 40-pin header (-M versions) |
| GPIO 38 | GPIO, PWM | On the 40-pin header (-M versions) |
| GPIO 16 | GPIO, PWM, ADC | On the header; LCD TE line, not connected by default |
| GPIO 17 | GPIO, PWM, ADC | On the header; LCD reset line, not connected by default |
| GPIO 43 | GPIO, PWM, UART_TX | UART0 TX on the header |
| GPIO 44 | GPIO, PWM, UART_RX | UART0 RX on the header |
- 40-pin header (-M versions) — GPIO 43, 44, 0, 1, 2, 3, 11, 12, 13, 14, 15, 19, 20, 21, 26, 33, 34, 35, 36, 37, 38, 39, 40, 4, 10, 16, 17 · 2 x 20 pin header
Only the -M versions have headers. GPIO 33-37 are wired to the header but used by the octal PSRAM
Good to know before you start
- It isn't supported in the LCD Ultra Pro editor yet.
- The -M versions have headers. The others have no easy GPIO access at all.
- Waveshare's playful examples need arduino-esp32 below 3.0 (2.0.9 works).
What it is good for
- •Wide status strips
- •Desk tickers and clocks
- •Motion-reactive displays
LVGL support in LCD Ultra Pro™
This board is documented in the wiki, but it is not in the LCD Ultra Pro™ editor yet, so you can’t pick it there or export a project for it. The specs, pins and connectors on this page come from the manufacturer’s own material and are there to help you wire and configure it. See the board list for boards the editor supports today.
Arduino IDE settings
From the manufacturer's documentation (not tested by us yet)
| Board | ESP32S3 Dev Module |
|---|---|
| USB CDC On Boot | Enabled |
| Flash Size | 16MB (128Mb) |
| Partition Scheme | 16M Flash (3MB APP/9.9MB FATFS) |
| PSRAM | OPI PSRAM |
Board package: esp32 by Espressif Systems
Menu items the manufacturer doesn't mention are left at their defaults. We haven't compiled a driver for this board ourselves yet. Manufacturer's source
Frequently asked questions
Does the ESP32-S3-AMOLED-1.91 have touch?
Only the Touch-AMOLED-1.91 versions. The plain AMOLED-1.91 and -M boards have no touch panel.
What is the resolution?
536×240 pixels on a 1.91-inch AMOLED.
What does -M mean?
The -M versions come with pin headers; the versions without -M have no headers.
Sources
Specifications cross-checked against the manufacturer’s documentation (last checked 2026-11-04):
More in the Waveshare AMOLED family
- Waveshare ESP32-C6-Touch-AMOLED-1.64
- Waveshare ESP32-S3 Touch AMOLED 1.64"
- Waveshare ESP32-C6-Touch-AMOLED-1.8
- Waveshare ESP32-S3-Touch-AMOLED-1.8
- Waveshare ESP32-C6-Touch-AMOLED-2.06
- Waveshare ESP32-S3-Touch-AMOLED-2.06
- Waveshare ESP32-C6-Touch-AMOLED-2.16
- Waveshare ESP32-S3-Touch-AMOLED-2.16
- Waveshare ESP32-S3 Touch AMOLED 2.41"
Tools for this board
Connect sensors and parts
- 28BYJ-48 stepper
- A4988 stepper driver
- ACS712 current sensor
- ADS1115 ADC
- ADXL345 accelerometer
- AHT20
- AS5600 magnetic encoder
- BH1750
- BME280
- BME680
- BMP280
- BTS7960 motor driver
- CAN bus (SN65HVD230)
- Capacitive soil moisture
- DFPlayer Mini
- DHT22 / AM2302
- DS18B20
- DS3231 RTC
- EC11 rotary encoder
- ENS160
- HC-SR04
- HC-SR501 PIR
- HX711 load cell
- INA219
- INA226
- INMP441 microphone
- IRLZ44N MOSFET
- KY-023 joystick
- 4x4 matrix keypad
- LD2410 radar
- LDR photoresistor
- MAX31855 thermocouple
- MAX7219 LED matrix
- MAX98357A I2S amp
- MCP23017 GPIO expander
- microSD card
- MLX90614 IR thermometer
- MPU6050
- MQ-2 gas sensor
- NEO-6M GPS
- NTC thermistor 10k
- PCA9685 PWM driver
- Piezo buzzer
- Push button
- PZEM-004T
- RC522 RFID
- 5 V relay module
- RS-485 (MAX3485)
- SCD40
- SG90 servo
- SHT31 / SHT3x
- SIM800L GSM
- SSD1306 OLED
- SSR-40DA relay
- LoRa SX1276
- TB6612FNG motor driver
- TCS34725 colour sensor
- TP4056 battery charger
- TTP223 touch button
- VL53L0X
- WS2812B LED strip
- YF-S201 flow sensor
Last updated:
Adding I2C sensors to this board?See which addresses its own chips already use, and what would clash.Open the checkerSomething wrong on this page?
Tell me what you found. I check every report and fix the page.